The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board > The 1973 - 1991 Blazers, Jimmys, and Suburbans Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-31-2007, 11:33 AM   #1
79blazer
Registered User
 
79blazer's Avatar
 
Join Date: Aug 2006
Location: Mesa, Arizona
Posts: 136
Collapsible steering shaft?

I am trying to replace my Rag joint in my 1979 2wd Blazer and once I unbolt the 2 bolts to the steering shaft it would not collapse. It looks like it should. (It does on my other Chevy an 85 caprice!) Is there something I am forgetting? I would prefer not to remove the steering box because that is a PITA. thanks
__________________
79 Blazer Cheyenne, 2wd 305 3.42 stock
85 Caprice, TBI converted, new 350 crate motor, Monte Carlo SS Wheels, Bilstein shocks,
79blazer is offline   Reply With Quote
Old 01-31-2007, 11:30 PM   #2
DirtyLarry
Windy Corner of a Dirty Street
 
DirtyLarry's Avatar
 
Join Date: Jun 2003
Location: Pueblo West, Colorado
Posts: 2,926
Re: Collapsible steering shaft?

Yes, it collapses but you would need to drag out the smoke wrench to melt the vinyl sheer point plugs between the upper and lower sections, which I would not recommend doing.

You shouldn’t need to fully remove the gear box. Remove all the bolts but leave one loosely holding the box to the frame so you can wiggle it around enough to sneak the rag joint off the gear box input shaft and intermediate shaft. It can be done.

Good luck and have fun.
DirtyLarry is offline   Reply With Quote
Old 02-01-2007, 02:50 AM   #3
ghetto_superman
Registered User
 
ghetto_superman's Avatar
 
Join Date: Sep 2006
Location: Omaha, NE
Posts: 1,982
Re: Collapsible steering shaft?

A little motivation from your favorite big hammer will get that shaft to collapse...
__________________
-1947 3100 -1968 C10 -1970 K20
ghetto_superman is offline   Reply With Quote
Old 02-01-2007, 10:26 AM   #4
79blazer
Registered User
 
79blazer's Avatar
 
Join Date: Aug 2006
Location: Mesa, Arizona
Posts: 136
Re: Collapsible steering shaft?

Thanks. Motivation with a 3 foot crow bar got the job done without breaking the vinyl plug. The fire wall flexes... but I didn't hurt it. Oh life is much better now. The quarter of a turn of the steering wheel play is gone. I also adjusted the bolt on top. Tightened it then backed up a half turn. I have heard there's another adjusting bolt elsewhere on the steering box but can't find it. Is there one?
__________________
79 Blazer Cheyenne, 2wd 305 3.42 stock
85 Caprice, TBI converted, new 350 crate motor, Monte Carlo SS Wheels, Bilstein shocks,
79blazer is offline   Reply With Quote
Old 02-01-2007, 01:24 PM   #5
DirtyLarry
Windy Corner of a Dirty Street
 
DirtyLarry's Avatar
 
Join Date: Jun 2003
Location: Pueblo West, Colorado
Posts: 2,926
Re: Collapsible steering shaft?

I think you are talking about adjusting the worm gear in the gear box. Be careful, as you can do more harm than good by adjusting that. It doesn’t take much to go to far then the truck will not return to center as you make turns and it will steer touchy as hell.

It is not really a bolt to adjust the worm gear. There is a set screw in the aluminum pitman shaft cap that is visible from under the hood near the radiator support. You will need a wrench and hex key to adjust it. Proceed with caution.
DirtyLarry is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:42 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com