SOLD! 4x4 Chassis - rolling ps pb bbc T350 $700.00 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

1968SWBBigBlock · 08-18-2007, 09:21 PM

I have a mid 70's GM frame, front/rear axles,leaf springs, NP205 transfer case, Dana 44 front, 12 bolt rear, power steering box,power steering pump, power brakes (hydro boost), Turbo 350 with converter, big block chevy motor mounts, headers, 6 bolt wheels, disc brakes up front, drums in the back Everything appears to work correctly
I am selling this as a rolling chassis no engine no body

$700.00

Thanks

Bill

1968SWBBigBlock · 08-22-2007, 10:27 AM

I will break the set up if anyone has an interest -the frame is shot(found out after we pulled the body off) so only the parts will do -
Shot me an offer

chevys2die4 · 08-22-2007, 06:56 PM

What type of rims are they?

1968SWBBigBlock · 08-22-2007, 09:14 PM

The rims are old american racing chrome plated rusty rims - not worth much

1968SWBBigBlock · 08-26-2007, 09:31 PM

OK I did find that tag and confirmed that this is an NP205 Dated in late 1972
So it should be out of a 73 truck
The rearend is dated 272 making it an early 72 rearend so it has most likley been swapped in, I am going to pull the covers and confirms insides and gears
The hydro boost MC is gone so What I have left is
Front Axle with Swaybar, Rear axle, leaf springs, PS box, PS booster, transfer case, T350 tranny, converter, NP205 adapter, 2 driveshafts and 4 shocks
$450.00 you pick and pull.
The body is off the chassis so it is easy to work on/
You can even take the entire roller if you want it

toomanytoyz · 08-27-2007, 02:13 PM

Where are you located in Ohio, Would like to do Mapquest Search to see if i Could make the Trip??

Thanks, Rick

Is This a LWB or Swb Frame?

1968SWBBigBlock · 08-27-2007, 09:15 PM

Located just north of Columbus in Sunbury Ohio 186 miles from you
I am easy to get to 5 minutes off rt 71
I will have to put a tape measure on it for length - my gut tells me it looks like a swb, let me know
\
Thanks

Bill

toomanytoyz · 08-28-2007, 07:15 PM

Do u Know if the Tranny is any Good? Could whole Thing be Pulled with a Tow Dolly? Any Overall Pics of the Frame? Did u measure it Yet?

Thanks, Rick

1969k10stepside · 08-28-2007, 07:20 PM

Rick,it looks like a good donor for the 1 ton wrecker build.I hope you get it.If you do,I may be interested in buying the sway bar and top spring plates for the swaybar,from you.....Heck,I could use the front driveshaft too.

Dustin

78 street c10 · 08-28-2007, 08:48 PM

Why is the frame shot? Rust?

1968SWBBigBlock · 08-28-2007, 09:12 PM

Yes the frame is rusty - If you are interested let me know I am more interested in selling it than keeping it.

Thanks

Bill

toomanytoyz · 08-29-2007, 09:56 AM

Quote:

Originally Posted by toomanytoyz

Do u Know if the Tranny is any Good? Could whole Thing be Pulled with a Tow Dolly? Any Overall Pics of the Frame? Did u measure it Yet?

Thanks, Rick

Did u Get a Chance to Check Yet?

Thanks, Rick

1968SWBBigBlock · 08-29-2007, 04:42 PM

Toomany - man so sorry I totally missed your request.
Yes it can be towed with a dolly.
No I have not hit it with a tape measure
Yes the tranny is good
The truck last drove as a complete truck 8 days ago.
I will grab a some addtional photos and post them tonight.

toomanytoyz · 08-29-2007, 04:51 PM

Thanks, I would appreciate That. Im mainly interested in the Tranny & Transfer Case Combo for my Wrecker Project, However i would Take the Whole Thing To Make it Easier for Both of Us.

Only Reason ??? Length is for Driveshaft.........

Thanks Again, Rick

1968SWBBigBlock · 08-29-2007, 07:08 PM

Here are the pictures of the chassis.

I measured it and it is 116" which matchs my short bed truck.
116" center of hub to center of hub

let me know what else you need.

1968SWBBigBlock · 08-29-2007, 08:53 PM

SOLD to TOMANYTOYZ

Thanks

Bill

toomanytoyz · 08-29-2007, 10:12 PM

Deposit sent via Paypal...............

Thanks again for the Deal on The Frame, Rick

1969k10stepside · 08-29-2007, 10:39 PM

Congrats on the purchase Rick.Be safe when you go to pick it up

toomanytoyz · 09-05-2007, 08:52 PM

Went & picked up the Frame Today, A Special Thank You To Bill & His Son Nick for All The Help with Loading. They also Did a Great Job of Having the Frame Ready For Hauling, Tranny was Braced, Driveshaft Disconnected & Ready To Roll.

Towed it About 200 Miles with no Problem, Again a Big Thank Guy's & It was a Pleasure To Meet You Both. Good Luck on Getting the New Motor in Your Truck Bill................

Thanks, Rick

Bill & Nick Getting Frame Ready To Load.............

Frame Loaded On THe Tow Dolly....................

Ready For Home...............

08-18-2007, 09:21 PM	#1
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	SOLD! 4x4 Chassis - rolling ps pb bbc T350 $700.00 I have a mid 70's GM frame, front/rear axles,leaf springs, NP205 transfer case, Dana 44 front, 12 bolt rear, power steering box,power steering pump, power brakes (hydro boost), Turbo 350 with converter, big block chevy motor mounts, headers, 6 bolt wheels, disc brakes up front, drums in the back Everything appears to work correctly I am selling this as a rolling chassis no engine no body $700.00 Thanks Bill Attached Images __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree

08-22-2007, 10:27 AM	#2
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 I will break the set up if anyone has an interest -the frame is shot(found out after we pulled the body off) so only the parts will do - Shot me an offer __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree

08-22-2007, 06:56 PM	#3
chevys2die4 Junior Member Join Date: Aug 2005 Location: Bryan,OH Posts: 157	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 What type of rims are they? __________________ 68 SB 396 72 SB CHEYENNE 402 04 Silverado SS

08-22-2007, 09:14 PM	#4
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 The rims are old american racing chrome plated rusty rims - not worth much __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree

08-26-2007, 09:31 PM	#5
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 OK I did find that tag and confirmed that this is an NP205 Dated in late 1972 So it should be out of a 73 truck The rearend is dated 272 making it an early 72 rearend so it has most likley been swapped in, I am going to pull the covers and confirms insides and gears The hydro boost MC is gone so What I have left is Front Axle with Swaybar, Rear axle, leaf springs, PS box, PS booster, transfer case, T350 tranny, converter, NP205 adapter, 2 driveshafts and 4 shocks $450.00 you pick and pull. The body is off the chassis so it is easy to work on/ You can even take the entire roller if you want it __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree

08-27-2007, 02:13 PM	#6
toomanytoyz Luv the Crewcabs Join Date: Aug 2006 Location: Andrews, In. 46702 Posts: 4,097	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Where are you located in Ohio, Would like to do Mapquest Search to see if i Could make the Trip?? Thanks, Rick Is This a LWB or Swb Frame?

08-27-2007, 09:15 PM	#7
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Located just north of Columbus in Sunbury Ohio 186 miles from you I am easy to get to 5 minutes off rt 71 I will have to put a tape measure on it for length - my gut tells me it looks like a swb, let me know \ Thanks Bill __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree

08-28-2007, 07:15 PM	#8
toomanytoyz Luv the Crewcabs Join Date: Aug 2006 Location: Andrews, In. 46702 Posts: 4,097	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Do u Know if the Tranny is any Good? Could whole Thing be Pulled with a Tow Dolly? Any Overall Pics of the Frame? Did u measure it Yet? Thanks, Rick

08-28-2007, 07:20 PM	#9
1969k10stepside Registered User Join Date: Mar 2006 Location: USA Posts: 21,019	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Rick,it looks like a good donor for the 1 ton wrecker build.I hope you get it.If you do,I may be interested in buying the sway bar and top spring plates for the swaybar,from you.....Heck,I could use the front driveshaft too. Dustin Last edited by 1969k10stepside; 08-28-2007 at 07:21 PM.

08-28-2007, 08:48 PM	#10
78 street c10 Registered User Join Date: Aug 2007 Location: newark Posts: 6	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Why is the frame shot? Rust?

08-28-2007, 09:12 PM	#11
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Yes the frame is rusty - If you are interested let me know I am more interested in selling it than keeping it. Thanks Bill __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree

08-29-2007, 04:42 PM	#13
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Toomany - man so sorry I totally missed your request. Yes it can be towed with a dolly. No I have not hit it with a tape measure Yes the tranny is good The truck last drove as a complete truck 8 days ago. I will grab a some addtional photos and post them tonight. __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree

08-29-2007, 04:51 PM	#14
toomanytoyz Luv the Crewcabs Join Date: Aug 2006 Location: Andrews, In. 46702 Posts: 4,097	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Thanks, I would appreciate That. Im mainly interested in the Tranny & Transfer Case Combo for my Wrecker Project, However i would Take the Whole Thing To Make it Easier for Both of Us. Only Reason ??? Length is for Driveshaft......... Thanks Again, Rick

08-29-2007, 07:08 PM	#15
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Here are the pictures of the chassis. I measured it and it is 116" which matchs my short bed truck. 116" center of hub to center of hub let me know what else you need. Attached Images __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree

08-29-2007, 08:53 PM	#16
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 SOLD to TOMANYTOYZ Thanks Bill __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree



Register or Log In To remove these advertisements.

08-29-2007, 10:12 PM	#17
toomanytoyz Luv the Crewcabs Join Date: Aug 2006 Location: Andrews, In. 46702 Posts: 4,097	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Deposit sent via Paypal............... Thanks again for the Deal on The Frame, Rick

08-29-2007, 10:39 PM	#18
1969k10stepside Registered User Join Date: Mar 2006 Location: USA Posts: 21,019	Re: 4x4 Chassis - rolling ps pb bbc T350 $700.00 Congrats on the purchase Rick.Be safe when you go to pick it up

09-05-2007, 08:52 PM	#19
toomanytoyz Luv the Crewcabs Join Date: Aug 2006 Location: Andrews, In. 46702 Posts: 4,097	Re: SOLD! 4x4 Chassis - rolling ps pb bbc T350 $700.00 Went & picked up the Frame Today, A Special Thank You To Bill & His Son Nick for All The Help with Loading. They also Did a Great Job of Having the Frame Ready For Hauling, Tranny was Braced, Driveshaft Disconnected & Ready To Roll. Towed it About 200 Miles with no Problem, Again a Big Thank Guy's & It was a Pleasure To Meet You Both. Good Luck on Getting the New Motor in Your Truck Bill................ Thanks, Rick Bill & Nick Getting Frame Ready To Load............. Frame Loaded On THe Tow Dolly.................... Ready For Home...............

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.