Having fits trying to make this brace fit! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BIG CHEVY 3600 · 08-15-2008, 08:19 PM

This is the brace that runs from the steering column up to the cowl however I can not get it to fit in there. It seems to be about an inch too long.
There is a mystery to this part and I don't know the answer. I did the tear down on the truck and took all parts to the blaster. I don't remember removing this brace and when the truck came back the brace was removed and about 1.5 inches cut off from it. I welded it back but it won't fit. I can't say I didn't remove it when I did the tear down but I know for sure I didn't cut the end off.
I would appreciate some advice on this subject, a measurement of your brace and or pictures of where on the cowl it mounts.

http://good-times.webshots.com/photo...99708909ulHlcZ

http://good-times.webshots.com/photo...99708909dOJKxj
_________________________

Augy's '53 · 08-15-2008, 09:04 PM

I can only guess that you aren't putting enough 'angle' on the bracket. If you look @ your picture named motor, you will see 2 bolts above and inboard of the voltage reg. these are the bolts that are going thru the square holes of the bracket. the other end is the column support.

Atomsplitter · 08-15-2008, 09:21 PM

Yes I remember that piece on a '49 I used to own. It was a ***** to get out and I remember thinking it would be a bigger one trying to put it in. It has one end that is held in place at the firewall. I had to almost buckle the firewall and pull on the dash to get it out. I'd sooner cut it in 2 and weld it back together inplace.

BIG CHEVY 3600 · 08-15-2008, 09:22 PM

Andy:
I have tried every angle it just doesn't want to fit. It seems to be about 1 or 1.5 inches too long. When I place the bottom end up where it is supposed to go at the steering column the other end won't straighten out even at the top of the cowl. I'm about ready to cut some off of it. But it just doesn't make sense why it won't fit.

cajundragger · 08-15-2008, 11:03 PM

I took mine out, and threw it away.

BIG CHEVY 3600 · 08-15-2008, 11:41 PM

Cajun:
I would do the same but I'm afraid it might be really needed to brace the dash and firewall.

50adrod · 08-16-2008, 06:29 PM

this may help. if you enlarge this pic you can see how it is mounted in my '50. the firewall does not need it for bracing but the dash might.

BIG CHEVY 3600 · 08-16-2008, 11:31 PM

Got it in finally. I had to bend the firewall end back about an inch to make it fit. Thanks guys for all the suggestions.

08-15-2008, 08:19 PM	#1
BIG CHEVY 3600 BIG CHEVY 3600 LONGBOX Join Date: Feb 2008 Location: Dallas, Texas Posts: 382	Having fits trying to make this brace fit! This is the brace that runs from the steering column up to the cowl however I can not get it to fit in there. It seems to be about an inch too long. There is a mystery to this part and I don't know the answer. I did the tear down on the truck and took all parts to the blaster. I don't remember removing this brace and when the truck came back the brace was removed and about 1.5 inches cut off from it. I welded it back but it won't fit. I can't say I didn't remove it when I did the tear down but I know for sure I didn't cut the end off. I would appreciate some advice on this subject, a measurement of your brace and or pictures of where on the cowl it mounts. http://good-times.webshots.com/photo...99708909ulHlcZ http://good-times.webshots.com/photo...99708909dOJKxj _________________________ __________________ If I were given 8 hours to chop down a large tree, I would spend the first 6 hours sharpening my ax. Abraham Lincoln http://s729.photobucket.com/albums/w...cpZZ3QQtppZZ20 Last edited by BIG CHEVY 3600; 08-15-2008 at 08:19 PM.

08-15-2008, 09:04 PM	#2
Augy's '53 Registered User Join Date: Aug 2008 Location: Sierra Vista, AZ Posts: 9	Re: Having fits trying to make this brace fit! I can only guess that you aren't putting enough 'angle' on the bracket. If you look @ your picture named motor, you will see 2 bolts above and inboard of the voltage reg. these are the bolts that are going thru the square holes of the bracket. the other end is the column support.

08-15-2008, 09:21 PM	#3
Atomsplitter Registered User Join Date: Mar 2006 Location: Ontario Posts: 514	Re: Having fits trying to make this brace fit! Yes I remember that piece on a '49 I used to own. It was a ***** to get out and I remember thinking it would be a bigger one trying to put it in. It has one end that is held in place at the firewall. I had to almost buckle the firewall and pull on the dash to get it out. I'd sooner cut it in 2 and weld it back together inplace.

08-15-2008, 09:22 PM	#4
BIG CHEVY 3600 BIG CHEVY 3600 LONGBOX Join Date: Feb 2008 Location: Dallas, Texas Posts: 382	Re: Having fits trying to make this brace fit! Andy: I have tried every angle it just doesn't want to fit. It seems to be about 1 or 1.5 inches too long. When I place the bottom end up where it is supposed to go at the steering column the other end won't straighten out even at the top of the cowl. I'm about ready to cut some off of it. But it just doesn't make sense why it won't fit. __________________ If I were given 8 hours to chop down a large tree, I would spend the first 6 hours sharpening my ax. Abraham Lincoln http://s729.photobucket.com/albums/w...cpZZ3QQtppZZ20

08-15-2008, 11:03 PM	#5
cajundragger Registered User Join Date: Aug 2006 Location: louisiana Posts: 1,008	Re: Having fits trying to make this brace fit! I took mine out, and threw it away.

08-15-2008, 11:41 PM	#6
BIG CHEVY 3600 BIG CHEVY 3600 LONGBOX Join Date: Feb 2008 Location: Dallas, Texas Posts: 382	Re: Having fits trying to make this brace fit! Cajun: I would do the same but I'm afraid it might be really needed to brace the dash and firewall. __________________ If I were given 8 hours to chop down a large tree, I would spend the first 6 hours sharpening my ax. Abraham Lincoln http://s729.photobucket.com/albums/w...cpZZ3QQtppZZ20

08-16-2008, 06:29 PM	#7
50adrod Registered User Join Date: Jun 2008 Location: Louisiana Posts: 493	Re: Having fits trying to make this brace fit! this may help. if you enlarge this pic you can see how it is mounted in my '50. the firewall does not need it for bracing but the dash might. __________________ 1971 Corvette convertible 454@ 525 hp 1936 Chevy Truck street rod 1952 Chevy truck hot rod build http://www.killbillet.com/showthread...2-Chevy-Cut-up 1964 F 100 custom street rod http://www.ford-trucks.com/forums/12...mark-viii.html 1950 custom Chevy Truck Last edited by 50adrod; 08-16-2008 at 06:31 PM.

08-16-2008, 11:31 PM	#8
BIG CHEVY 3600 BIG CHEVY 3600 LONGBOX Join Date: Feb 2008 Location: Dallas, Texas Posts: 382	Re: Having fits trying to make this brace fit! Got it in finally. I had to bend the firewall end back about an inch to make it fit. Thanks guys for all the suggestions. __________________ If I were given 8 hours to chop down a large tree, I would spend the first 6 hours sharpening my ax. Abraham Lincoln http://s729.photobucket.com/albums/w...cpZZ3QQtppZZ20

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.