Starting 72 rear axle install.. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

gulfcoast66 · 11-06-2008, 11:50 AM

Well I got some stuff yesterday for my rear end, hopefully i will have time to do it this week end. Im still trying too get back on my feet since the storm (IKE) anyways thats all im going say about that. So for i have cleaned and painted the axle and installed new brak shoes. I have new u-bolts and gasket for cover. I got the thing from pick-a- you know the rest, last year. Inspection inside was good. its from a 1972 1/2 burban with 4.11s. Iwas thinking swapping 3.73s from my 6lug axle, but im just ready to put that thing under my truck and be that closer to being finished my truck.

gulfcoast66 · 11-06-2008, 11:53 AM

[IMG]

[/IMG]

gulfcoast66 · 11-06-2008, 11:55 AM

[IMG]

[/IMG]

gulfcoast66 · 11-06-2008, 03:09 PM

Having a hard time removing the old u-bolts from the trailing arms. If i cut them ill still have the problem of getting whats left out the trailing arms!!

Are there any tricks to pop them out whole. Any help would be app. Thx Chris.

ChopperDr · 11-06-2008, 03:23 PM

PB Blaster and a BFH. You can get lots of things done with just those two items.

From the PB Blaster site-"Quickly breaks loose the surface tension of frozen parts and protects against further rust and corrosion."

Spray it down, let it sit a bit, then beat the hell out of it. The rust and scale should break down and allow the bolts to be driven out.

Chopster

**Captainfab** · 11-06-2008, 04:51 PM

If you have a torch you can heat up the area of the trailing arms where the U bolts go thru and that'll break them loose. Don't get it too hot though. If nothing else you can cut the U bolts off and then you have a little more room on the topside to swing a BFH to drive out what is left in the trailing arms.

gulfcoast66 · 11-06-2008, 05:02 PM

Yeah CaptianFab that look like what im going to have to do. Im starting to bend my trailing arms prying and hamming on them. anyway im beat work a 12 last night off 2 days. Ill cut 2 morro and see what happens. Chris..

p_rubottom · 11-06-2008, 05:07 PM

I have had to cut a few, I soaked them with wd and used a big pipe wrench to twist the remaining part out of the trailing arm. Good luck!!

kizer · 11-06-2008, 06:09 PM

I personally cut the U-bolts as low as possible making 3 pieces. The arch was basically cut out.

I then pulled the trailing arm off the cross member and then I sprayed the heck out of the bolt and let it penatrate the trailing arm. I then flipped the arm over on its top and pushed down and the bolt pushed down and well the nut side pushed out. Just make sure you put all of the weight on the cut off bolt not the trailing arm its self.

Oh I forgot to mention I did lower the arm as low as I could with it still connected and U-bolt cut and gave it a few good wacks with a peice of wood under it so I could hammer the nut side down. The trick of course being I soaked the arm with PB blaster the day before and just before I hit it. AFter I hit it a few times with a small hammer I then used some channel locks and twisted the U-bolt then I took it off and did what I mentioned in the paragraph up above.

Looks like you bought the same bolts as I did.

Rogue 64 · 11-06-2008, 07:06 PM

Quote:

Originally Posted by ChopperDr

PB Blaster and a BFH. You can get lots of things done with just those two items.

I used to use PB alot, but tried "Deep Creep" and it kicks the rust out of PB.

http://www.seafoamsales.com/deepCreepTech.htm

Try it for yourself, that and a lead hammer.

gulfcoast66 · 11-07-2008, 11:26 PM

Well i got a little time today to work on those rusty u-bolts, I soaked them last night with some koil and today cut them, the rear side of the bolts just dropped out but the front parts fight to the bloody end! any way i blocked the trailing arms up and sprayed,beat and turned them until they came out. I cleaned everything up and 2morro I will start putting everything back to gether.

gulfcoast66 · 11-07-2008, 11:27 PM

[IMG]

[/IMG]

gulfcoast66 · 11-07-2008, 11:31 PM

[IMG]

[/IMG]

gulfcoast66 · 11-07-2008, 11:33 PM

[IMG]

[/IMG]

gulfcoast66 · 11-07-2008, 11:35 PM

[IMG]

[/IMG]

gulfcoast66 · 11-07-2008, 11:37 PM

[IMG]

[/IMG]

gulfcoast66 · 11-09-2008, 09:25 PM

Man I am finished with the install of the rear axel. Ran into a couple of problems 1) The washers that lmc sent were to big to fit the bottom of the shock bracket, So im glad i did not thow anything away 2) My panhard bar dont fit anymore, but my truck is sitting on its own weight, Oh yeah the72 is a little wider then the 66 rear. do anybody know were the best priced panhard bar are? Chris..

gulfcoast66 · 11-09-2008, 09:34 PM

[IMG]

[/IMG]

gulfcoast66 · 11-09-2008, 09:35 PM

[IMG]

[/IMG]

gulfcoast66 · 11-09-2008, 09:37 PM

[IMG]

[/IMG]

gulfcoast66 · 11-09-2008, 09:38 PM

[IMG]

[/IMG]

gulfcoast66 · 11-09-2008, 09:39 PM

[IMG]

[/IMG]

joe231 · 11-09-2008, 09:50 PM

looks good!!

gulfcoast66 · 11-09-2008, 10:41 PM

Thanks Joe!

joe231 · 11-09-2008, 11:03 PM

cpp 1965-72 Adj. Track Bar - 24” long $59.99
LINKY

that is all i can find right now, but there are plenty more out there
why won't your work? shows 65-72 are the same

11-06-2008, 11:50 AM	#1
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Starting 72 rear axle install.. Well I got some stuff yesterday for my rear end, hopefully i will have time to do it this week end. Im still trying too get back on my feet since the storm (IKE) anyways thats all im going say about that. So for i have cleaned and painted the axle and installed new brak shoes. I have new u-bolts and gasket for cover. I got the thing from pick-a- you know the rest, last year. Inspection inside was good. its from a 1972 1/2 burban with 4.11s. Iwas thinking swapping 3.73s from my 6lug axle, but im just ready to put that thing under my truck and be that closer to being finished my truck. __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-06-2008, 11:53 AM	#2
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-06-2008, 11:55 AM	#3
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-06-2008, 03:09 PM	#4
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. Having a hard time removing the old u-bolts from the trailing arms. If i cut them ill still have the problem of getting whats left out the trailing arms!! Are there any tricks to pop them out whole. Any help would be app. Thx Chris. __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-06-2008, 03:23 PM	#5
ChopperDr Registered User Join Date: Feb 2008 Location: WA Posts: 189	Re: Starting 72 rear axle install.. PB Blaster and a BFH. You can get lots of things done with just those two items. From the PB Blaster site-"Quickly breaks loose the surface tension of frozen parts and protects against further rust and corrosion." Spray it down, let it sit a bit, then beat the hell out of it. The rust and scale should break down and allow the bolts to be driven out. Chopster

11-06-2008, 04:51 PM	#6
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: Starting 72 rear axle install.. If you have a torch you can heat up the area of the trailing arms where the U bolts go thru and that'll break them loose. Don't get it too hot though. If nothing else you can cut the U bolts off and then you have a little more room on the topside to swing a BFH to drive out what is left in the trailing arms. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

11-06-2008, 05:02 PM	#7
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. Yeah CaptianFab that look like what im going to have to do. Im starting to bend my trailing arms prying and hamming on them. anyway im beat work a 12 last night off 2 days. Ill cut 2 morro and see what happens. Chris.. __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-06-2008, 05:07 PM	#8
p_rubottom Registered User Join Date: Aug 2007 Location: Kansas Posts: 366	Re: Starting 72 rear axle install.. I have had to cut a few, I soaked them with wd and used a big pipe wrench to twist the remaining part out of the trailing arm. Good luck!!

11-06-2008, 06:09 PM	#9
kizer Its Deja Vu time again Join Date: Aug 2008 Location: Marysville, North of Seattle WA Posts: 815	Re: Starting 72 rear axle install.. I personally cut the U-bolts as low as possible making 3 pieces. The arch was basically cut out. I then pulled the trailing arm off the cross member and then I sprayed the heck out of the bolt and let it penatrate the trailing arm. I then flipped the arm over on its top and pushed down and the bolt pushed down and well the nut side pushed out. Just make sure you put all of the weight on the cut off bolt not the trailing arm its self. Oh I forgot to mention I did lower the arm as low as I could with it still connected and U-bolt cut and gave it a few good wacks with a peice of wood under it so I could hammer the nut side down. The trick of course being I soaked the arm with PB blaster the day before and just before I hit it. AFter I hit it a few times with a small hammer I then used some channel locks and twisted the U-bolt then I took it off and did what I mentioned in the paragraph up above. Looks like you bought the same bolts as I did. __________________ Its not pretty but its mine to figure out. The build / The Photos / Build Diary Last edited by kizer; 11-06-2008 at 06:13 PM.

11-07-2008, 11:26 PM	#11
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. Well i got a little time today to work on those rusty u-bolts, I soaked them last night with some koil and today cut them, the rear side of the bolts just dropped out but the front parts fight to the bloody end! any way i blocked the trailing arms up and sprayed,beat and turned them until they came out. I cleaned everything up and 2morro I will start putting everything back to gether. __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-07-2008, 11:27 PM	#12
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-07-2008, 11:31 PM	#13
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-07-2008, 11:33 PM	#14
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-07-2008, 11:35 PM	#15
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-07-2008, 11:37 PM	#16
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet



Register or Log In To remove these advertisements.

11-09-2008, 09:25 PM	#17
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. Man I am finished with the install of the rear axel. Ran into a couple of problems 1) The washers that lmc sent were to big to fit the bottom of the shock bracket, So im glad i did not thow anything away 2) My panhard bar dont fit anymore, but my truck is sitting on its own weight, Oh yeah the72 is a little wider then the 66 rear. do anybody know were the best priced panhard bar are? Chris.. __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-09-2008, 09:34 PM	#18
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-09-2008, 09:35 PM	#19
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-09-2008, 09:37 PM	#20
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-09-2008, 09:38 PM	#21
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-09-2008, 09:39 PM	#22
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. [IMG][/IMG] __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-09-2008, 09:50 PM	#23
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Starting 72 rear axle install.. looks good!! __________________ *CHEVY ONLY*

11-09-2008, 10:41 PM	#24
gulfcoast66 64-66 CHEVY JUNKIE Join Date: Apr 2007 Location: Cypress ,Texas Posts: 1,516	Re: Starting 72 rear axle install.. Thanks Joe! __________________ 1966 C-10 Fleetside LWB, 350 Lt1 4l60-E 2008 Silverado Crew Cab, 4.8 4l60-E 1998 GMC Yukon 4x4 L-31 Vortec, 4l60-E 2017 GMC Serra 4x4 5.3 Vortec, 4l60-E Do It In A Chevrolet

11-09-2008, 11:03 PM	#25
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Starting 72 rear axle install.. cpp 1965-72 Adj. Track Bar - 24” long $59.99 LINKY that is all i can find right now, but there are plenty more out there why won't your work? shows 65-72 are the same __________________ *CHEVY ONLY* Last edited by joe231; 11-09-2008 at 11:04 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.