01-12-2009, 08:05 PM | #1 |
Registered User
Join Date: Jan 2009
Location: rardnor pa
Posts: 3
|
56 4x4 conversion
Working on a 56 GMC . Need help. Want to upgrade the chassis and convert to a 4x4. What would be a good year chassis to start with ? Thanks.
|
01-12-2009, 11:07 PM | #2 |
Registered User
Join Date: Nov 2008
Location: Texarkana, TX
Posts: 443
|
Re: 56 4x4 conversion
Mine had Jeep pickup (J20), axles, transfer and steering gearbox grafted on to my stock frame.
__________________
Brandon 63 Biscayne https://www.pro-touring.com/threads/90718-63-Biscayne 57 Chevy Truck (sold)http://67-72chevytrucks.com/vboard/s...d.php?t=321380 72 K20 Long bed stepside (wife's) 72 K20 Long bed 396 (flip or keep...?) The latest build: http://67-72chevytrucks.com/vboard/s...76#post8438476 |
01-12-2009, 11:50 PM | #3 |
Registered User
Join Date: Jun 2008
Location: Lubbock, TX
Posts: 2,047
|
Re: 56 4x4 conversion
I assume you're wanting to use a solid front rather than the newer IFS? I don't think there's a Chevy solid front axle that is narrow enough to even come close to staying inside the fenders. The rear of my '77 K-5 is 61" between wheel mounting surfaces and the front is about 4" wider. Try over at http://www.pirate4x4.com/welcome1.php, there's a lot of good info on there for several different brands. Good luck, a '56 4x4 will make for a badass truck. You might also try to find out what front GM used for the NAPCO 4x4's.
|
01-13-2009, 01:31 AM | #4 |
Registered User
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
|
Re: 56 4x4 conversion
I kept the stock frame and springs and used 74 axles, steering, trans and transfer case. Look at my build thread "Lurker Orrie" http://67-72chevytrucks.com/vboard/s...d.php?t=233305. Also there are some builds in the 4x4 section. I have a friend that is putting them on shortened early 90's 4wd dually frames too. Welcome...
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project |
01-13-2009, 01:04 PM | #5 |
Registered User
Join Date: Nov 2003
Location: Texas
Posts: 183
|
Re: 56 4x4 conversion
56 on 80 short 4x4 frame - Page 2 - The 1947 - Present Chevrolet ...Page 2- 56 on 80 short 4x4 frame The 1947 - 1959 Chevrolet & GMC Pickups Message Board.
67-72chevytrucks.com/vboard/showthread.php?t=290391&page=2 |
01-13-2009, 01:13 PM | #6 |
Registered User
Join Date: Nov 2003
Location: Texas
Posts: 183
|
Re: 56 4x4 conversion
also checkout page 1 of my thread
|
01-13-2009, 02:26 PM | #7 |
Registered User
Join Date: Jan 2009
Location: rardnor pa
Posts: 3
|
Re: 56 4x4 conversion
Thanks for all of the info. Great site Have a question for Gene. Your truck looks great , it is exactly what I would like to do . Was the frame from a pick up or a Blazer? I read that you had to move the fire wall back 2 inches. Was that just at the bottom or the whole thing? Thanks again.
|
01-13-2009, 02:42 PM | #8 |
Registered User
Join Date: Nov 2003
Location: Texas
Posts: 183
|
Re: 56 4x4 conversion
The frame on this one was an 80 short bed 4x4 frame it is approx 1'' longer than the frame on a 56 short bed and same width in back
The beds are pretty much the same just different back fenders I had to move the firewall back a couple of inches to clear dist when using stock 80 model motor mounts Would be best to move center section back a couple of inches most of way up and down clears well everywehre else Gene Last edited by Gene Sharp; 01-13-2009 at 02:45 PM. Reason: spelling |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|