3 speed trans question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

davidh · 01-23-2009, 10:45 AM

Okay I pulled my tranny out with my motor yesterday. I wanted to drain the old fluid and add new. How much does it hold? what kind do you suggest? also is there a seal at the back of the trans tail shaft? I dont want to add to it and it all leak out say like a automatic. If I have to add to it when its back in the truck where do I do that? I just see a drain plug. 66 trans

TimE · 01-23-2009, 11:25 AM

I don't recall right off how much it holds. There should be a fill plug on the side of the tranny. Fill it until fluid just starts to run out and you're good to go.

davidh · 01-23-2009, 11:49 AM

Hmm. what about the something purple oil, 20W-50 stuff.?? purple maxx?

*LILRED66* · 01-23-2009, 11:51 AM

Try posting a picture of the tranmission you have and you can get some good input on the model, fluid amount and type to use.

jason65 · 01-23-2009, 01:35 PM

Quote:

Originally Posted by davidh

Hmm. what about the something purple oil, 20W-50 stuff.?? purple maxx?

Isn't it Royal purple? My wife's son swares by it. But I haven't tried it.

davidh · 01-23-2009, 02:31 PM

pics of tranny here

MikeN · 01-23-2009, 04:23 PM

Fill plug is on the opposite side from the side shown in the photos. The rear seal is easily replaced...pry the old one out with a screwdriver, and gently tap the new one in with a hammer. As stated above, fill it until lube just begins to dribble out of the fill hole. You need two bottle of plain old 80W-90 gear lube. Personally, I'd stay away from synthetics in an older tranny like that.

ol Curt · 01-23-2009, 04:39 PM

Are you sure that's not one the recovered aircraft engines from the Hudson?

MacAttack · 01-23-2009, 05:47 PM

Quote:

Originally Posted by MikeN

You need two bottle of plain old 80W-90 gear lube. Personally, I'd stay away from synthetics in an older tranny like that.

+1 (a waste of good cash)

01-23-2009, 10:45 AM	#1
davidh Senior Member Join Date: Feb 2004 Location: Ponca city now kingfisher Oklahoma Posts: 1,220	3 speed trans question Okay I pulled my tranny out with my motor yesterday. I wanted to drain the old fluid and add new. How much does it hold? what kind do you suggest? also is there a seal at the back of the trans tail shaft? I dont want to add to it and it all leak out say like a automatic. If I have to add to it when its back in the truck where do I do that? I just see a drain plug. 66 trans __________________ Even the nicest dodge-chrysler is only 2years away from being parked outside of Section 8 housing.

01-23-2009, 11:25 AM	#2
TimE Hey Y'all!! Join Date: Dec 2007 Location: Bay Minette, Alabama Posts: 1,755	Re: 3 speed trans question I don't recall right off how much it holds. There should be a fill plug on the side of the tranny. Fill it until fluid just starts to run out and you're good to go. __________________ Just hopin' I live long enough to finish something!!!

01-23-2009, 11:49 AM	#3
davidh Senior Member Join Date: Feb 2004 Location: Ponca city now kingfisher Oklahoma Posts: 1,220	Re: 3 speed trans question Hmm. what about the something purple oil, 20W-50 stuff.?? purple maxx? __________________ Even the nicest dodge-chrysler is only 2years away from being parked outside of Section 8 housing.

01-23-2009, 11:51 AM	#4
LILRED66 Account Suspended Join Date: May 2005 Location: Kansas City, KS Posts: 3,906	Re: 3 speed trans question Try posting a picture of the tranmission you have and you can get some good input on the model, fluid amount and type to use.

01-23-2009, 02:31 PM	#6
davidh Senior Member Join Date: Feb 2004 Location: Ponca city now kingfisher Oklahoma Posts: 1,220	Re: 3 speed trans question pics of tranny here Attached Images __________________ Even the nicest dodge-chrysler is only 2years away from being parked outside of Section 8 housing.

01-23-2009, 04:23 PM	#7
MikeN Registered User Join Date: Oct 2007 Location: Marietta, GA Posts: 805	Re: 3 speed trans question Fill plug is on the opposite side from the side shown in the photos. The rear seal is easily replaced...pry the old one out with a screwdriver, and gently tap the new one in with a hammer. As stated above, fill it until lube just begins to dribble out of the fill hole. You need two bottle of plain old 80W-90 gear lube. Personally, I'd stay away from synthetics in an older tranny like that.

01-23-2009, 04:39 PM	#8
ol Curt Junior Member Join Date: Dec 2006 Location: Newburgh, IN Posts: 1,247	Re: 3 speed trans question Are you sure that's not one the recovered aircraft engines from the Hudson?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.