extracting glove box liner - The 1947 - Present Chevrolet & GMC Truck Message Board Network

TomJohnston · 10-23-2009, 05:38 PM

Can you give me any tips or tricks? After the door comes off and all the screws are out how do you get the big thing out of the small hole?

Oh, and thanks in advance. Even the stupid questions I've asked have been answered by you guys! (and gals?)

*72lb4x4* · 10-23-2009, 05:59 PM

If you can't push it in and down, you just have to get a bit violent with it and push in the center areas of the sides and work it out through the opening.

It goes back in the same way.

That's at least how I've done it in the past...

**Thealien** · 10-23-2009, 06:05 PM

If it is an AC truck it is a pain in the A**! Work around the edges until it is all inside the opening and then pull one side out first. It goes in a lot easier than it came out!

Good luck

*vegaschevy* · 10-23-2009, 06:08 PM

both old truck boxes I removed tore before they were out

TomJohnston · 10-23-2009, 06:13 PM

Quote:

Originally Posted by vegaschevy

both old truck boxes I removed tore before they were out

Now that's encouraging :\

Yes it's an AC truck. I can get the top, bottom, and one side out but when I pull on the other one the first one goes back in.

Jayss109 · 10-23-2009, 06:29 PM

My vote is use the flamethrower!

**Thealien** · 10-23-2009, 06:58 PM

Quote:

Originally Posted by TomJohnston

Now that's encouraging :\

Yes it's an AC truck. I can get the top, bottom, and one side out but when I pull on the other one the first one goes back in.

Take your time and you will get it. I tore mine a little getting it out and put some duck tape on the backside before re installing and you can't tell. The good news is you can get reproduction ones from most of the venders fairly inexpensive.

gmcdude · 10-23-2009, 07:02 PM

Mine came from the under side of the dash.

**Thealien** · 10-23-2009, 09:35 PM

Quote:

Originally Posted by gmcdude

Mine came from the under side of the dash.

Is your truck an AC truck?

dan42 · 10-23-2009, 09:38 PM

Spend the 15 bucks and get a new one. They're just cardboard anyways, and 40 year old cardboard isn't as good as new cardboard.

unclewatts · 10-24-2009, 04:06 AM

If you don't have air (like me) you can just slip it under the dash, work it up to the hole and it pops right in without any damage. If you have air, my condolences.

**leddzepp** · 10-24-2009, 11:05 AM

I replaced both of mine (in A/C trucks) Here is how I did it:

Step 1: Cuss and yell, and rip the old one out.

Step 2: Buy a new one for about $10 and install it.

TomJohnston · 10-26-2009, 02:16 PM

Quote:

Originally Posted by Thealien

Is your truck an AC truck?

It is an AC truck but I need to do all of the ventilation tubing so I might end up taking out the plenum and air control anyway. I'm hoping I can do do it through the dash hole and behind the instruments.

10-23-2009, 05:38 PM	#1
TomJohnston Registered User Join Date: May 2009 Location: somewhere, MN Posts: 110	extracting glove box liner Can you give me any tips or tricks? After the door comes off and all the screws are out how do you get the big thing out of the small hole? Oh, and thanks in advance. Even the stupid questions I've asked have been answered by you guys! (and gals?)

10-23-2009, 05:59 PM	#2
72lb4x4 Account Suspended Join Date: Jul 2006 Location: DFW Posts: 1,427	Re: extracting glove box liner If you can't push it in and down, you just have to get a bit violent with it and push in the center areas of the sides and work it out through the opening. It goes back in the same way. That's at least how I've done it in the past...

10-23-2009, 06:05 PM	#3
Thealien Senior Member Join Date: Jun 2007 Location: Pine Ridge Florida Posts: 4,135	Re: extracting glove box liner If it is an AC truck it is a pain in the A**! Work around the edges until it is all inside the opening and then pull one side out first. It goes in a lot easier than it came out! Good luck

10-23-2009, 06:08 PM	#4
vegaschevy Account Suspended Join Date: May 2009 Location: las vegas nv Posts: 1,493	Re: extracting glove box liner both old truck boxes I removed tore before they were out

10-23-2009, 06:29 PM	#6
Jayss109 Active Member Join Date: May 2005 Location: San Jose, CA Posts: 235	Re: extracting glove box liner My vote is use the flamethrower! __________________ Cadillac Powered

10-23-2009, 07:02 PM	#8
gmcdude Registered User Join Date: Jul 2009 Location: Abingdon, Virginia Posts: 300	Re: extracting glove box liner Mine came from the under side of the dash.

10-23-2009, 09:38 PM	#10
dan42 Registered User Join Date: Feb 2007 Location: Cali Central Coast Posts: 5,191	Re: extracting glove box liner Spend the 15 bucks and get a new one. They're just cardboard anyways, and 40 year old cardboard isn't as good as new cardboard. __________________ '67 SWB Fleetside ZZ4/350/Tremec 5-speed/4link/Scott's IFS - and fun as heck! SOLD Click here to support the board Philippians 4: 6-7

10-24-2009, 04:06 AM	#11
unclewatts 70 Chevrolet=Obsession Join Date: Jun 2009 Location: nice ca Posts: 1,067	Re: extracting glove box liner If you don't have air (like me) you can just slip it under the dash, work it up to the hole and it pops right in without any damage. If you have air, my condolences. __________________ I'm Just like my truck. Old, Ugly and Grouchy. Except my truck starts easily in the morning and doesn't smoke! IT'S NOT EASY BEING GREEN! -Kermit the frog 1970 Chevrolet C-10 Longbed Stepside : 350, Muncie M20, 3.08 GM corp. positraction Forest green exterior/light green interior(Where all my money goes) 1996 Toyota Corolla (Parts runner)

10-24-2009, 11:05 AM	#12
leddzepp Moderator Join Date: May 2007 Location: Southern Cal Posts: 20,048	Re: extracting glove box liner I replaced both of mine (in A/C trucks) Here is how I did it: Step 1: Cuss and yell, and rip the old one out. Step 2: Buy a new one for about $10 and install it. __________________ 1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.