CaptKaos, paging CaptKaos - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*1FaastC10* · 01-20-2003, 08:24 PM

your assistance is needed at FSC...

http://www.fullsizechevy.com/forum/s...928#post490928

**swervin ervin** · 01-20-2003, 08:46 PM

Jeremy,

here's his pics.

http://www.73-87.com/photos/tech/bumpertrim1.jpg

http://www.73-87.com/photos/tech/modifiedhorns.jpg

http://www.73-87.com/photos/tech/passbrkt.jpg

*1FaastC10* · 01-21-2003, 05:45 PM

thanks Mike

**Captkaos** · 01-21-2003, 06:25 PM

You take a long weekend vacation (of which I actually worked on the Jimmy) and I miss everything. Thanks for jumping in there Swerve for the recovery. I will put this up on the how to page for everyone....

*1FaastC10* · 01-22-2003, 01:37 AM

Chris, you say you worked on the Jimmy? get anything accomplished? i decided to "work on" mine today. but there's only so much a guy can do when its 20* outside, and you have no heat. basically, i'm just cleaning up the garage, getting it ready to start building my chassis. a buddy of mine is going to section my crossmember for me in return for some favors around his shop, spindles coils and a flip kit. hope everything goes smooth!

**Captkaos** · 01-22-2003, 03:53 PM

Yeah, I got a little accomplished. Put the door handles and key locks in, put the driveshaft in, put the radiator, shroud and hoses on, trans lines hooked up, and some miscellaneous wiring hooked up. I loaned out my batttery, so I could check everything inside. But I got it back yesterday. It was in the 60's here Monday, so I got some stuff done. I am trying to get it to the exhaust shop to get some mufflers and pipes ran.

01-20-2003, 08:24 PM	#1
1FaastC10 Account Suspended Join Date: Oct 2002 Location: Elkhart, IN Posts: 6,399	CaptKaos, paging CaptKaos your assistance is needed at FSC... http://www.fullsizechevy.com/forum/s...928#post490928

01-20-2003, 08:46 PM	#2
swervin ervin You get what you pay for Join Date: Dec 1999 Location: Cherryville, NC Posts: 4,798	Jeremy, here's his pics. http://www.73-87.com/photos/tech/bumpertrim1.jpg http://www.73-87.com/photos/tech/modifiedhorns.jpg http://www.73-87.com/photos/tech/passbrkt.jpg __________________ Mike 1985 Chevy C-10

01-21-2003, 06:25 PM	#4
Captkaos www.73-87chevytrucks.com Join Date: Dec 1999 Location: Birmingham, AL Posts: 6,935	You take a long weekend vacation (of which I actually worked on the Jimmy) and I miss everything. Thanks for jumping in there Swerve for the recovery. I will put this up on the how to page for everyone.... __________________ Chris Lucas 1973 Chevy C-10 1978 GMC Jimmy (2WD) - SOLD 1987 R10 twin turbo LS 1991 R3500 SRW CrewCab 1985 K5 diesel swapped project 1989 K5 2WD conversion w/ Vette susp Project Captkaos Customs 73-87chevytrucks.com

01-22-2003, 03:53 PM	#6
Captkaos www.73-87chevytrucks.com Join Date: Dec 1999 Location: Birmingham, AL Posts: 6,935	Yeah, I got a little accomplished. Put the door handles and key locks in, put the driveshaft in, put the radiator, shroud and hoses on, trans lines hooked up, and some miscellaneous wiring hooked up. I loaned out my batttery, so I could check everything inside. But I got it back yesterday. It was in the 60's here Monday, so I got some stuff done. I am trying to get it to the exhaust shop to get some mufflers and pipes ran. __________________ Chris Lucas 1973 Chevy C-10 1978 GMC Jimmy (2WD) - SOLD 1987 R10 twin turbo LS 1991 R3500 SRW CrewCab 1985 K5 diesel swapped project 1989 K5 2WD conversion w/ Vette susp Project Captkaos Customs 73-87chevytrucks.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-21-2003, 05:45 PM	#3
1FaastC10 Account Suspended Join Date: Oct 2002 Location: Elkhart, IN Posts: 6,399	thanks Mike

01-22-2003, 01:37 AM	#5
1FaastC10 Account Suspended Join Date: Oct 2002 Location: Elkhart, IN Posts: 6,399	Chris, you say you worked on the Jimmy? get anything accomplished? i decided to "work on" mine today. but there's only so much a guy can do when its 20* outside, and you have no heat. basically, i'm just cleaning up the garage, getting it ready to start building my chassis. a buddy of mine is going to section my crossmember for me in return for some favors around his shop, spindles coils and a flip kit. hope everything goes smooth!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.