The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Racing and high performance (trucks haulin more than hay)

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-23-2013, 12:16 AM   #1
Rannos
Registered User
 
Rannos's Avatar
 
Join Date: Feb 2010
Location: New Caney, Texas
Posts: 356
Getting close.

Been trying to finish this truck up but seems the more I do the more I need to do. I have been running it around town for about a month now with 18" of 3" pipe and a pair of 2 chamber Flowmasters. I finally got off my arse and me and my brothers ran the new exhaust. 3" pipes exit just before the rear tires with the short Dynomax race bullets. Not sure how or if I like it. Idling it has a cleaner sound but after 20+ years of always running Flowmasters the Dynomax mufflers just sound, well different. Here is a video of it idling right after finishing it up.
Only things i lack now are the new tranny that's getting built atm and the new drive shaft.


Rannos is offline   Reply With Quote
Old 02-23-2013, 07:54 PM   #2
BigDan3131
Registered User
 
BigDan3131's Avatar
 
Join Date: Jun 2006
Location: Maple Valley, WA
Posts: 1,913
Re: Getting close.

You wont really know if you like it or not until you are cruising around town and can see if it drones like Flowmasters sometimes do.
__________________
Custom Painter/Restoration Specialist

1965 GMC 3/4 Ton LB SOLD?
1964 Chevy El Camino in full restoration
1991 Chevy S10 288K+ miles 2nd Owner SOLD

2020 RAM 1500 Warlock
BigDan3131 is offline   Reply With Quote
Old 02-23-2013, 09:54 PM   #3
Rannos
Registered User
 
Rannos's Avatar
 
Join Date: Feb 2010
Location: New Caney, Texas
Posts: 356
Re: Getting close.

It doesn't drone like the flowmasters did. It's alot louder even with the added length. Will have to seenifnt hey grow on me.
Posted via Mobile Device
Rannos is offline   Reply With Quote
Old 02-23-2013, 10:06 PM   #4
cableguy0
Senior Member
 
Join Date: Apr 2000
Location: Delta,Pa
Posts: 14,948
Re: Getting close.

I prefer 10 series flowmaster in race apps with mufflers. Im running about 5 feet of 3 inch pipe into 10 series with nothing on the back end. It just dumps out the mufflers. Its deafening loud to those around me. Its loud in the truck but nothing too terrible
__________________
Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member.
cableguy0 is offline   Reply With Quote
Old 02-24-2013, 05:14 PM   #5
Rannos
Registered User
 
Rannos's Avatar
 
Join Date: Feb 2010
Location: New Caney, Texas
Posts: 356
Re: Getting close.

Well then truck isn't just for the track. I was trying to get away from how terribly loud and disorted it was. Now it's louder just not distorted like it was. I love how they sound at idle.... yhey just have a raspy soun d under throttle that I am not use to.
Posted via Mobile Device
Rannos is offline   Reply With Quote
Old 02-26-2013, 02:05 AM   #6
redsled87
Registered User
 
redsled87's Avatar
 
Join Date: Dec 2011
Location: Lanc Co PA
Posts: 226
Re: Getting close.

It sounds bad a$$!
__________________
1987 R10 Pump Gas 496/TH375
Best 1/4 pass to date
60' 1.49
1/4 10.93
MPH 120
redsled87 is offline   Reply With Quote
Old 02-26-2013, 07:33 AM   #7
Rannos
Registered User
 
Rannos's Avatar
 
Join Date: Feb 2010
Location: New Caney, Texas
Posts: 356
Re: Getting close.

Thanks Red. We made a few videos under throttle. I sont tjink it sounds bad. It just sounds alott different then I expected and is terribly loud.


https://www.youtube.com/watch?v=FPrU...e_gdata_player
Posted via Mobile Device
Posted via Mobile Device
Rannos is offline   Reply With Quote
Old 02-26-2013, 07:35 AM   #8
Rannos
Registered User
 
Rannos's Avatar
 
Join Date: Feb 2010
Location: New Caney, Texas
Posts: 356
Re: Getting close.

Other video didnt post for some reason.


https://www.youtube.com/watch?v=i-Xs...e_gdata_player
Posted via Mobile Device
Rannos is offline   Reply With Quote
Old 02-27-2013, 04:00 AM   #9
BigDan3131
Registered User
 
BigDan3131's Avatar
 
Join Date: Jun 2006
Location: Maple Valley, WA
Posts: 1,913
Re: Getting close.

Its probably quieter now without a floor in the bed.
__________________
Custom Painter/Restoration Specialist

1965 GMC 3/4 Ton LB SOLD?
1964 Chevy El Camino in full restoration
1991 Chevy S10 288K+ miles 2nd Owner SOLD

2020 RAM 1500 Warlock
BigDan3131 is offline   Reply With Quote
Old 02-27-2013, 01:23 PM   #10
Rannos
Registered User
 
Rannos's Avatar
 
Join Date: Feb 2010
Location: New Caney, Texas
Posts: 356
Re: Getting close.

Well it hasnt had a floor in the bed sence I owned it so I dont think it made a difference.
Posted via Mobile Device
Rannos is offline   Reply With Quote
Old 03-16-2013, 11:41 AM   #11
Rannos
Registered User
 
Rannos's Avatar
 
Join Date: Feb 2010
Location: New Caney, Texas
Posts: 356
Re: Getting close.

Got my new wheels in and had them mounted yesterday. 15x6 front and 15x12 rears with 215/70 r15 fronts and 315/60 r15 MT drag radials rear. Looks and rides like a whole different truck.
Attached Images
    
Rannos is offline   Reply With Quote
Old 03-16-2013, 03:48 PM   #12
Rannos
Registered User
 
Rannos's Avatar
 
Join Date: Feb 2010
Location: New Caney, Texas
Posts: 356
Re: Getting close.

Took this last night at a small local get together. The 1915 Tall T next to my truck belongs to the fella that owns Wabbit's Wood Works. They make all the wood panels for early American cars and some gauge setups. Is a really cool guy and an awesome lil all steel Model T.
Attached Images
  
Rannos is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:31 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com