NC 250 Parts & Power Steering Brackets - The 1947 - Present Chevrolet & GMC Truck Message Board Network

shelby2828 · 06-05-2013, 10:47 PM

All of my spare parts are officially SOLD thanks Dave, it was nice meeting you, good luck with your stovebolt!

On to the parts!
250 Power steering brackets, these were pulled from a 69 impala (non-integrated head) SOLD in the lower 48.
PN on the bracket that mounts below the PS pump is 3973156 and the smaller bracket with just 2 holes is 3973157

These brackets are complete as pulled off the car in the yard, I cannot recall exactly how the whole thing went together, please note that the Alt bracket (long slotted bracket) is chewed up, I am not sure what happened to it.

shelby2828 · 06-05-2013, 10:52 PM

Complete setup with everything but the Crank pulley, these were pulled from a "built" 250 motor I was going to swap into my truck...but alas, plans changed! I believe this motor was from a 1972 nova, but I cannot confirm the vintage of the brackets, but it was also a non-integrated head.
PN on the small slotted bracket is AAD-2782A01 / 354526

2 Groove WP pulley for a 250 PS setup
PN 355776AX

250 PS pulley (and the pump if you want it). This came from the 69 Impala
PN 3860457CV

These are painted and ready to go, just a bit dusty and crusty
$old!

shelby2828 · 06-05-2013, 10:55 PM

SOLD

Monojet Rochester Carb, I pulled this in favor of a 4bbl "economaster" carb...BIG mistake, lost a lot of low end torque! This has a manual choke and was on a running truck, but has been on the shelf for 7 years, so a rebuild would probably be a good idea.
$45 plus shipping.

shelby2828 · 06-05-2013, 10:56 PM

See above

shelby2828 · 06-05-2013, 10:58 PM

250 Steering Arm (not sure if this transfers to a 2wd truck or not) again, from the 69 Impala
PN 941796
SOLD

shelby2828 · 06-05-2013, 10:59 PM

250 "turbo fire" 1bbl intake air cleaner
$35 plus shipping.
SOLD

*mrdana60* · 06-05-2013, 11:08 PM

Would you do 40 shipped on breather?

shelby2828 · 06-05-2013, 11:11 PM

Also, not pictured I have a power steering box for a 67 4x4 that I dismantled in an attempt to rebuild it, and lost interest when I discovered it was beyond me! $10 plus shipping (some assembly required)

**jabborabbo** · 06-05-2013, 11:33 PM

I'll take the Rochester carb...PM inbound.

shelby2828 · 06-05-2013, 11:43 PM

Please include your zip when requesting a shipping estimate (either in pm or reply)

Thanks!
Posted via Mobile Device

shelby2828 · 06-06-2013, 09:24 AM

All PM's replied.

shelby2828 · 06-07-2013, 09:33 AM

I have had a couple of questions about the exhaust manifold, the heat riser swings freely without binding, and opens quickly (albeit a bit squeaky) and completely from manually closing it.

shelby2828 · 06-08-2013, 08:45 PM

Bump for the 250 guys, if it is still pictured, it is still available.
Posted via Mobile Device

shelby2828 · 06-12-2013, 04:11 PM

Exhaust and linkage sold, ps, and intake still available.
Posted via Mobile Device

shelby2828 · 06-16-2013, 08:08 PM

Weekend bump
Posted via Mobile Device

shelby2828 · 06-23-2013, 03:10 PM

Ttt for all us stovebolt guys!
Posted via Mobile Device

Dirt's72 · 06-24-2013, 08:11 AM

Shelby,
Do you think any of your stuff will fit my stuff.

http://67-72chevytrucks.com/vboard/s...27#post6139527

My motor is from a 73 nova

I don't want to go to the junk yard again and don't want to put down $200
for something that won't fit.
Posted via Mobile Device

shelby2828 · 06-24-2013, 09:11 AM

Dirt, the painted set came off of an early 70's 250 setup (the brackets and the double groove pulley) I bought the engine out of the car, but I do know that is what it was intended to go into.
I cannot speak to any issues there maybe with the pump, I think they should all mount the same way (for a 250), but I am by no means a stovebolt expert.
I will ship the pulley and brackets together for the asking price.
Posted via Mobile Device

shelby2828 · 07-01-2013, 12:43 PM

Bump

Dirt's72 · 07-11-2013, 11:13 PM

What kind of deal for all the ps brackets. I will return what I don't need to get me running?
Posted via Mobile Device

shelby2828 · 07-12-2013, 10:22 AM

Pm sent on package deal at a shipped price.
Posted via Mobile Device

BigBlack · 08-29-2013, 06:33 PM

was looking for a P/S bracket set for a 250 wanted to know if you still had a full set left??? 80601 for shipping thanks!!!

shelby2828 · 07-10-2013, 04:11 PM

Bump, willing to cut deals on items purchased together
Posted via Mobile Device

shelby2828 · 08-02-2013, 05:37 PM

Bump, I can make a package deal for anyone interested.

Vintage Windmills · 08-03-2013, 01:07 AM

do you have 67 ram assist 4x4 steering parts? Also, any chance the PS brackets fit a 292?

06-05-2013, 10:47 PM	#1
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	250 Parts & Power Steering Brackets All of my spare parts are officially SOLD thanks Dave, it was nice meeting you, good luck with your stovebolt! On to the parts! 250 Power steering brackets, these were pulled from a 69 impala (non-integrated head) SOLD in the lower 48. PN on the bracket that mounts below the PS pump is 3973156 and the smaller bracket with just 2 holes is 3973157 These brackets are complete as pulled off the car in the yard, I cannot recall exactly how the whole thing went together, please note that the Alt bracket (long slotted bracket) is chewed up, I am not sure what happened to it. Last edited by shelby2828; 11-06-2013 at 06:59 PM.

06-05-2013, 10:52 PM	#2
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Complete setup with everything but the Crank pulley, these were pulled from a "built" 250 motor I was going to swap into my truck...but alas, plans changed! I believe this motor was from a 1972 nova, but I cannot confirm the vintage of the brackets, but it was also a non-integrated head. PN on the small slotted bracket is AAD-2782A01 / 354526 2 Groove WP pulley for a 250 PS setup PN 355776AX 250 PS pulley (and the pump if you want it). This came from the 69 Impala PN 3860457CV These are painted and ready to go, just a bit dusty and crusty $old! Last edited by shelby2828; 11-06-2013 at 06:54 PM.

06-05-2013, 10:55 PM	#3
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets SOLD Monojet Rochester Carb, I pulled this in favor of a 4bbl "economaster" carb...BIG mistake, lost a lot of low end torque! This has a manual choke and was on a running truck, but has been on the shelf for 7 years, so a rebuild would probably be a good idea. $45 plus shipping. Last edited by shelby2828; 06-06-2013 at 11:00 AM. Reason: Item Sold

06-05-2013, 10:56 PM	#4
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets See above Last edited by shelby2828; 09-24-2013 at 02:13 PM.

06-05-2013, 10:58 PM	#5
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets 250 Steering Arm (not sure if this transfers to a 2wd truck or not) again, from the 69 Impala PN 941796 SOLD Last edited by shelby2828; 11-06-2013 at 06:55 PM.

06-05-2013, 10:59 PM	#6
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets 250 "turbo fire" 1bbl intake air cleaner $35 plus shipping. SOLD Last edited by shelby2828; 06-09-2013 at 11:32 AM.

06-05-2013, 11:08 PM	#7
mrdana60 Account Suspended Join Date: Sep 2010 Location: centre al Posts: 2,471	Re: 250 Parts & Power Steering Brackets Would you do 40 shipped on breather?

06-05-2013, 11:11 PM	#8
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Also, not pictured I have a power steering box for a 67 4x4 that I dismantled in an attempt to rebuild it, and lost interest when I discovered it was beyond me! $10 plus shipping (some assembly required)

06-05-2013, 11:33 PM	#9
jabborabbo Senior Member Join Date: Apr 2013 Location: Podunk, Texas Posts: 773	Re: 250 Parts & Power Steering Brackets I'll take the Rochester carb...PM inbound.

06-05-2013, 11:43 PM	#10
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Please include your zip when requesting a shipping estimate (either in pm or reply) Thanks! Posted via Mobile Device

06-06-2013, 09:24 AM	#11
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets All PM's replied.

06-07-2013, 09:33 AM	#12
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets I have had a couple of questions about the exhaust manifold, the heat riser swings freely without binding, and opens quickly (albeit a bit squeaky) and completely from manually closing it.

06-08-2013, 08:45 PM	#13
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Bump for the 250 guys, if it is still pictured, it is still available. Posted via Mobile Device

06-12-2013, 04:11 PM	#14
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Exhaust and linkage sold, ps, and intake still available. Posted via Mobile Device

06-16-2013, 08:08 PM	#15
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Weekend bump Posted via Mobile Device



Register or Log In To remove these advertisements.

06-23-2013, 03:10 PM	#16
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Ttt for all us stovebolt guys! Posted via Mobile Device

06-24-2013, 08:11 AM	#17
Dirt's72 Registered User Join Date: May 2013 Location: Albuquerque, NM Posts: 1,106	Re: 250 Parts & Power Steering Brackets Shelby, Do you think any of your stuff will fit my stuff. http://67-72chevytrucks.com/vboard/s...27#post6139527 My motor is from a 73 nova I don't want to go to the junk yard again and don't want to put down $200 for something that won't fit. Posted via Mobile Device

06-24-2013, 09:11 AM	#18
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Dirt, the painted set came off of an early 70's 250 setup (the brackets and the double groove pulley) I bought the engine out of the car, but I do know that is what it was intended to go into. I cannot speak to any issues there maybe with the pump, I think they should all mount the same way (for a 250), but I am by no means a stovebolt expert. I will ship the pulley and brackets together for the asking price. Posted via Mobile Device

07-01-2013, 12:43 PM	#19
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Bump

07-11-2013, 11:13 PM	#20
Dirt's72 Registered User Join Date: May 2013 Location: Albuquerque, NM Posts: 1,106	Re: 250 Parts & Power Steering Brackets What kind of deal for all the ps brackets. I will return what I don't need to get me running? Posted via Mobile Device

07-12-2013, 10:22 AM	#21
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Pm sent on package deal at a shipped price. Posted via Mobile Device

08-29-2013, 06:33 PM	#22
BigBlack Registered User Join Date: Jul 2009 Location: Brighton, CO Posts: 24	Re: 250 Parts & Power Steering Brackets was looking for a P/S bracket set for a 250 wanted to know if you still had a full set left??? 80601 for shipping thanks!!! __________________ Projects -- 72 Chevy k10 4x4 lwb 350/350 69 Chevy c10/CST 2x4 lwb BB 396

07-10-2013, 04:11 PM	#23
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Bump, willing to cut deals on items purchased together Posted via Mobile Device

08-02-2013, 05:37 PM	#24
shelby2828 Registered User Join Date: May 2013 Location: Raleigh Posts: 46	Re: 250 Parts & Power Steering Brackets Bump, I can make a package deal for anyone interested.

08-03-2013, 01:07 AM	#25
Vintage Windmills Vintage 4x4s Join Date: Sep 2010 Location: Prior Lake, MN Posts: 4,305	Re: 250 Parts & Power Steering Brackets do you have 67 ram assist 4x4 steering parts? Also, any chance the PS brackets fit a 292? __________________ 67 GMC K1500 Custom- 305V6 SM420, PTO, Ram Assist, yellow (the outcast) (project period correct upgrades) 67 GMC C2500 351V6 TH400, AC, PS, PB (can't decide what to do with. Update, decided to keep and will restore ) 86 CHV K30 502 th400, apple red NEW 71 CHV K20 350 SM465, ochre (saved work truck) 71 CHV K20 292 SM465, white, tach, PTO, (future project) 72 CHV K20 350 350th, medium blue (project stocker) 01 CHV K2500hd crew, indigo blue ^3 dont run and the others don't see winter either '86 K30 Cummins "Fireside" thread: http://67-72chevytrucks.com/vboard/s...d.php?t=649649 '71 K20 "get driveable" thread: http://67-72chevytrucks.com/vboard/s...d.php?t=590642 '72 K20 Build Thread: http://67-72chevytrucks.com/vboard/s...=493477&page=6

Register or Log In To remove these advertisements.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode