Keeping them stock

[Jack Guzman]

I noticed here that almost everyone who starts a build gets an old truck and proceeds to replace everything inside and under it with modern hot rod equipment. I wanted an old truck because I like wrenching on my own equipment but hate what emission controls and computer technology has done to modern vehicles. I like being able to repair problems with a few simple hand tools and common sense. I drove an s-10 for years.I had to pay someone to diagnose and repair it.My 81 stepside short bed beater had a 250 with all the emission hoses bypassed and a manual choke.The truck rotted away and I didn't think it was worth restoring.I hated the body style.
I think these redone machines are nice to drive,nice to look at but that is a whole different area of interest. I like old trucks. Anybody got any stories,photos of builds that restored nice old trucks to their original condition?
I'd like to see someone try to drive one of those low riders on one of the gravel roads around here.---Jack

[nvrdone]

Jack: you are right - most of the rides on this forum are extensively modified.
If you are more into stock / restored trucks you might want to check out stovebolt.com
They are more into the original trucks
Good luck.

[Rednek13x]

I bought my 57 with the intent to restore it to like new condition. After getting it running and road worthy, and driving it over 1000 miles this past summer, iv changed my mind. The truck has never been a problem, never skipped a beat, never let me down. Im young enough to where the rough ride doesnt bother me. But iv got to the point where i want to enjoy my truck more. So im going to run a 350 instead of the 235, air ride suspention. Everything else on the body/interior will be stock. Now i should be comfortable driving it down the interstate going more than 50mph.

[mr48chev]

I think Redneck 13X hit right on the what and why most guys on here modify their trucks somewhat rather than restore them to showroom stock. They want to get out and drive them and drive them long distances at today's highway speeds and with the need of more modern engines ability to hold up to such speeds and distances.

A lot of those the guys who swap to a mild 350 or later model 250 or 292 six keep the exterior and interior of the truck pretty much all original looking though rather than dechrome or otherwise modify those parts.

I don't have anything against a fully restored to showroom stock truck except that If I had one I probably would never drive it except to a few local shows that were within 100 miles of the house and a two hour drive. Locally while you see the 53 Chevy truck with the 10,000 dollar paint job (documented but not bragged about) with it's fi engine and automatic running up and down the valley and further on a weekly basis you see a number of "restored" trucks riding on trailers to shows 20 miles from home base because the owners don't want to put miles on them, are afraid to get road rash on them or would rather drive the crew cab tow rig with it's leather seats and ac. Some will tell you that their 20K restored truck is too valuable to drive while they tow it with a 50K dualie in a 10 K enclosed trailer.

I don't really car how a guy restores or builds his truck as long as he/she doesn't create an unsafe vehicle to be different or scab it together haphazardly with suspect workmanship due to "not having money to spend on it". It doesn't take a lot of money to do it right if you take your time and hunt down the deals.

[mikec4193]

Hi Jack

My smelly old 2 cents on old trucks...I love them...I grew up in the 1960's and 1970's and my dad never had a new truck...I recall an old Dodge Pilothouse from the 1950's era....I remember old step vans made into work trucks...they were all really cool...
The last project I finished was a 1947 Willys Jeep..I kept it as stock as I could except I went to 12 volts, added 3 point seat belts and also LED tail lights to make it brighter at night...it is one super cool truck..my main issue is it wont keep up with the modern day traffic flow...so I don't use it much...I do start it up and run it around my yard once every couple of weeks...
So my next project is going to be a 1 ton 1951 Chevy truck...cant wait to get it home and get fiddling with it...I guess it runs so that is a plus...I am going to upgrade the brakes first....rewire it second....I want it to be an old truck when I am done....I love the patina on the old stuff too...

MikeC

[lowrodderchev]

Originally Posted by Rednek13x

I bought my 57 with the intent to restore it to like new condition. After getting it running and road worthy, and driving it over 1000 miles this past summer, iv changed my mind. The truck has never been a problem, never skipped a beat, never let me down. Im young enough to where the rough ride doesnt bother me. But iv got to the point where i want to enjoy my truck more. So im going to run a 350 instead of the 235, air ride suspention. Everything else on the body/interior will be stock. Now i should be comfortable driving it down the interstate going more than 50mph.

hey Rednek13 you got anymore pix of that truck looks pretty sweet from the avatar

[lowrodderchev]

Originally Posted by Jack Guzman

I noticed here that almost everyone who starts a build gets an old truck and proceeds to replace everything inside and under it with modern hot rod equipment. I wanted an old truck because I like wrenching on my own equipment but hate what emission controls and computer technology has done to modern vehicles. I like being able to repair problems with a few simple hand tools and common sense. I drove an s-10 for years.I had to pay someone to diagnose and repair it.My 81 stepside short bed beater had a 250 with all the emission hoses bypassed and a manual choke.The truck rotted away and I didn't think it was worth restoring.I hated the body style.
I think these redone machines are nice to drive,nice to look at but that is a whole different area of interest. I like old trucks. Anybody got any stories,photos of builds that restored nice old trucks to their original condition?
I'd like to see someone try to drive one of those low riders on one of the gravel roads around here.---Jack

my truck came from my father who got it from my grandfather who got it new my dad had it stock and when I got I ran it stock (ok had a drop axle) till a unfort event took place due to frame damage its rocking some suspension mods and not once has my dad looked at it with disapproval most of the things ive done hes always wanted to do. its one of those to each his own things. my fleetline is all stock lowered a bit I drive the crud out that bad boy seen freeways backroads bad side of town good side of town and all the other sides of town. my truck will end up down a gravel bumpy road soon or later just like my fleetline as long as theres no bolts or nuts in my rear view mirror im good

[VTX-Black]

This is a timely thread for me.

I've been sitting on the fence for over a year, afraid to tamper with it having read where people want "unmolested" trucks, yet knowing that it is a lot of work to drive it often the way it is.

But recently I have come across a number of unmolested trucks that, while not show room trailer queen restorations, are still solid old trucks not going for much money.

This makes me wonder where the "original" truck market even is, let alone where it will be in a few short years when more people older than me get out of the hobby.

I'm staring to wonder if I should start swapping parts with that old 84 Vette that I bought as a parts car, rather than sell the Vette and keep the truck original.

[dcmalone]

I like my old truck because it's old. I'll probably never put an IFS or four-link under it, but I did add disk brakes and am running a 350sbc/200 4r combination. I enjoy getting on the interstate if I want to and being able to stop when someone pulls over in front of you and jams on the brakes because they don't plan ahead of their next turn. With drums all the way around I had to know that I was going to stop on down the road. I always leave plenty of room between me an the car in front of me, but for some reason that gives other people the sense that that's where they need to be. I'm making my safe and a pleasure to drive whenever I feel like, not just when it's between 70-74 degrees on completely sunny days. I do however like to look at all of 'em whether a $100,000 showpiece or one like mine that is built as I go.

[fabguy]

I absolutely love cars & trucks. I highly respect the guys that have put the time and effort into restoring to original and the ones that are mixed with aftermarket and original parts, heck some of those new fenders you buy today probably used to be old American cars & trucks anyway hahaha.
If you like IFS great! Disk brakes great! Straight axel great! Drum brakes great !
As for me personally, if I was to find an umolested, untouched, unaltered Chevy truck, I would personally cut it up too add Corvette IFS, Corvette IRS w/ coil overs LS3 engine, 700r4 trans, why? because that is what's GREAT! for me and my taste. wether anyone likes it or not, that's what I would buy it for.
My reason is that I want the reliability, power to go, the power to stop, and the comfort of knowing that I did it all myself.

[Jack Guzman]

Great responses. One of the things I like about this place.People respond.Not afraid to put in their 2 cents.I know there are are others that think like me I'm just trying to flush them out. I'll check out stovebolt.com cause it looks like there are more people there that don't modify everything.But if you all don't mind,I'll still hang around here. Alot of good information here and people talk to you. Besides even though it isn't my cup of tea,I love looking at all the beautifully modified trucks.---Jack

[lowrodderchev]

on the bright side you know were to go if your looking for a original parts jack LOL

[longbike]

Hey Jack!

I did my 57 back to original I just love the way old trucks were made back then and when I drive mine I want to be taken back into time the way it was back then, just my cup of tea,
but these guys on here with the modern mods are doing outstanding great jobs and I'm sure they do run and drive allot better so to each there own, do what ever you like, its your truck!

As for the stove bolt site, a great site but I just can't get into how the site is set up, being photos separate from the build log, to confusing and aggregating to use!

I like it here with these guys also!

[gale]

Originally Posted by fabguy

i absolutely love cars & trucks. I highly respect the guys that have put the time and effort into restoring to original and the ones that are mixed with aftermarket and original parts, heck some of those new fenders you buy today probably used to be old american cars & trucks anyway hahaha.
If you like ifs great! Disk brakes great! Straight axel great! Drum brakes great !
As for me personally, if i was to find an umolested, untouched, unaltered chevy truck, i would personally cut it up too add corvette ifs, corvette irs w/ coil overs ls3 engine, 700r4 trans, why? Because that is what's great! For me and my taste. Wether anyone likes it or not, that's what i would buy it for.
My reason is that i want the reliability, power to go, the power to stop, and the comfort of knowing that i did it all myself. :d

amen!

[MARTINSR]

Originally Posted by VTX-Black

This is a timely thread for me.

I've been sitting on the fence for over a year, afraid to tamper with it having read where people want "unmolested" trucks, yet knowing that it is a lot of work to drive it often the way it is.

But recently I have come across a number of unmolested trucks that, while not show room trailer queen restorations, are still solid old trucks not going for much money.

This makes me wonder where the "original" truck market even is, let alone where it will be in a few short years when more people older than me get out of the hobby.

I'm staring to wonder if I should start swapping parts with that old 84 Vette that I bought as a parts car, rather than sell the Vette and keep the truck original.

It's true the truck will never have a great value leaving it stock. Many cars this is true but a common vehicle like we are talking about a nicely updated one is worth more.

But that is such a tiny thought of mine, (none what so ever in fact) I want to drive what I want to drive. I drive a stone stock 59 Rambler everyday, I have a slightly modified 65 Buick Convertible for cruising and my truck that I am building will have every single ever loving inch of it cut and rewelded.

What do you WANT out of your truck, do it and enjoy it.

I don't get someone modifying their grand fathers Model A sedan that they just inherited, that makes no sense to me. But "just a car" that you bought, what the heck, do with it what you want.

Brian

[Jack Guzman]

Brian,
My buddy's mother drove a rambler back around the late 50s. I was in grammar school. I seem to remember a push button shifter? Does that sound right? Memory is a funny thing.---Jack

[VTX-Black]

Originally Posted by MARTINSR

It's true the truck will never have a great value leaving it stock. Many cars this is true but a common vehicle like we are talking about a nicely updated one is worth more.

But that is such a tiny thought of mine, (none what so ever in fact) I want to drive what I want to drive. I drive a stone stock 59 Rambler everyday, I have a slightly modified 65 Buick Convertible for cruising and my truck that I am building will have every single ever loving inch of it cut and rewelded.

What do you WANT out of your truck, do it and enjoy it.

I don't get someone modifying their grand fathers Model A sedan that they just inherited, that makes no sense to me. But "just a car" that you bought, what the heck, do with it what you want.

Brian

Thanks Brian (and thanks Jack for starting this thread)

For me, the nostalgia is in remembering swapping my sports car for my buddies 55 mornings on the way to high school and learning three in the tree.

Today, the idea of driving a 6 with three in the tree might be better than actually doing it though. As a novelty, I could be satisfied either way. It is more about getting out in the thing, and both ways would put a smile on my face for different reasons. THINKING…..

[Stepside Jim]

Good thread.... My situation, back in '82 I bought a '65 Corvette, not stock and in bad shape, perfect, I could afford it.

Over the years I heard repeatedly, "is it original"? It got tiring after a while.

Then comes Barret Jackson on Speed channel, and comes the term....."Resto-mod".

In my opinion that term changed the future of many otherwise stock rebuilds. Now putting in your personal touch is the norm anymore.

[gale]

I don't think I have ever left a truck or motorcycle like I found it but I also don't do radical modifications.

I also don't follow the herd. Just because something is the latest fad is often enough to steer me away.

[Speedbumpauto]

I think bone stock is a great way to go but not necessarilly a great way to stop.

[Dan in Pasadena]

Originally Posted by Speedbumpauto

I think bone stock is a great way to go but not necessarilly a great way to stop.

While I agree with you in general the truth is that what has changed is our expectations. If you're young enough to have driven power assisted disc brakes your entire driving life, then yes manual drum brake may well be dangerous.

If you allow for their greater pedal effort, longer stopping distances and adjust your speed, following distances, etc for them then you're a LOT safer than a person driving one of these that doesn't do that.

Having said all that? I'd only have single pot manual drum brakes on a restored show car. If I planned on street driving it, I'd go with dual reservoir front disc brakes no matter if the rest of the vehicle was dead stock.

[mechanixman]

I don't think anyone mentioned it yet, but I'm doing mine with a sbc and discs up front because it's cheaper. I can buy any sbc part off craigslist for less than $100, and new brake pads are a helluva lot cheaper than even reshoing the old shoes! (at least around here)
That being said, I'm still keeping the original 5 pedal configuration, same rear axle, manual steering. Now a big reason for keeping it that way is I'm 18, and have never really earned an appreciation for power steering/brakes. So I figured while I'm still young enough to screw around with it, why not?
Basically, I'm only updating what will be easier and cheaper to maintain during normal day to day use.

[meter swinger]

I like them all. Guess thats why I have 7 cars/trucks.

[flashed]

I like mine stock appearing on the outside but updates with motor and power brakes .My just restored 72 short fleetside has a couple of minor outside custom mods that most probably wont even notice at first glance and inside is mostly stock except for the BuddyBuckets and hidden stereo and cup holders .

[MARTINSR]

Originally Posted by VTX-Black

Thanks Brian (and thanks Jack for starting this thread)

For me, the nostalgia is in remembering swapping my sports car for my buddies 55 mornings on the way to high school and learning three in the tree.

Today, the idea of driving a 6 with three in the tree might be better than actually doing it though. As a novelty, I could be satisfied either way. It is more about getting out in the thing, and both ways would put a smile on my face for different reasons. THINKING…..

I do it every single day and have a ball.

Brian