The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board > The 1973 - 1991 Blazers, Jimmys, and Suburbans Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-18-2014, 04:02 PM   #1
eighteenninetytwo
Registered User
 
Join Date: Sep 2013
Location: Redwood city, CA
Posts: 694
Unlifting project.

OK I need to start planning the unlifting project for the truck. The actual work I'll try to do myself once I have parts, but before I even start that there are a ton of questions as this would be my first attempt at anything major myself. I am planning to take pics and post them of all of these areas for the experts here to comment on and make suggestions before I start anything.

The areas I THINK I'll need to look at are:

Suspension - will need new springs in front, new shocks all round, new U Bolts possibly all round at least in back. May need new springs in back if the 4" Blocks are integral to the existing springs (how do I figure THAT out?).

Steering - there seems to be a Dropped Pitman arm on the steering to accommodate the current lift.

Drive line - losing a 4 Inch lift, if pythagorus is to be believed, can make up to a half inch difference in the length needed of the rear driveline (ie it has to be shorter. Does the transfer case or the rear axle either mount or have components mounted in such a manner that such a difference can be accommodated, or does this operation require a change of (or to) the drive line?

Are there any other things I've missed here. Will take pics tomorrow and post them for comment / advice.
eighteenninetytwo is offline   Reply With Quote
Old 02-18-2014, 06:07 PM   #2
Eyegore
What Hump?
 
Eyegore's Avatar
 
Join Date: Apr 2003
Location: New River AZ
Posts: 2,009
Re: Unlifting project.

Are you going back to stock height? If it is a 4 inch lift your removing then you pretty much summed up what you need. I did not have to change my pitman when I removed a 6 inch lift. See if there is a suspension shop that makes their own U bolts they were far cheaper to have made, but that was over 20 years ago when I dropped mine.
__________________
Lil red 86 c-10
99 Sub
78 Camper Special w/ 454
Eyegore is offline   Reply With Quote
Old 02-18-2014, 08:39 PM   #3
68Timber
I know the pieces fit
 
68Timber's Avatar
 
Join Date: Nov 2007
Location: MONTGOMERY, AL
Posts: 5,523
Re: Unlifting project.

The rear blocks are sitting on the axle perch and the springs on top of them, it'll all separate when you get it up in the breeze, cut the u-bolts off, and lower the rear axle. You'll have to check the drive shafts to make sure they haven't been lengthened, I'm not sure if they have to be lengthened for a 4" lift or not but they do need to be checked.
__________________
John

79 2wd Blazer (Bruiser)
85 M1009 Blazer (Sarge) build
74 Honda Z50 build
68Timber is offline   Reply With Quote
Old 02-18-2014, 10:57 PM   #4
mickeykreg
Registered User
 
mickeykreg's Avatar
 
Join Date: Mar 2009
Location: salt lake city, utah
Posts: 208
Re: Unlifting project.

I'd also see what's going on with the brake lines. With a 4" they probably would've had to extended the brake line length to avoid stretching them at full flex. There's prob just drop brackets that can be removed in order to put them back to stock location.
__________________
'80 SRW C35 - 355/700R4/4:11/2.5-3/DD
'77 Cheyenne K5 - Roller cam 355/NV4500/205/4:88's/35's/DD

rust repair on the '77
http://67-72chevytrucks.com/vboard/s...d.php?t=740291
mickeykreg is offline   Reply With Quote
Old 02-19-2014, 12:14 AM   #5
eighteenninetytwo
Registered User
 
Join Date: Sep 2013
Location: Redwood city, CA
Posts: 694
Re: Unlifting project.

is that rear brake lines or front?? haev some pics but have to email them to myself before posting.
eighteenninetytwo is offline   Reply With Quote
Old 02-19-2014, 07:02 PM   #6
eighteenninetytwo
Registered User
 
Join Date: Sep 2013
Location: Redwood city, CA
Posts: 694
Re: Unlifting project.

Pics are not good I fear. Two of front suspension and one of back suspension. for some reason steering arm pic didn't come out. Any alarm bells from these?
Attached Images
   

Last edited by eighteenninetytwo; 02-19-2014 at 07:05 PM. Reason: more
eighteenninetytwo is offline   Reply With Quote
Old 02-24-2014, 04:45 PM   #7
eighteenninetytwo
Registered User
 
Join Date: Sep 2013
Location: Redwood city, CA
Posts: 694
Re: Unlifting project.

Here are some pics of the steering arm assembly. Any opinions as to whether I will need to change out components here.
Attached Images
   
eighteenninetytwo is offline   Reply With Quote
Old 02-24-2014, 04:57 PM   #8
mickeykreg
Registered User
 
mickeykreg's Avatar
 
Join Date: Mar 2009
Location: salt lake city, utah
Posts: 208
Re: Unlifting project.

Looks like the stock height steering arm so your good there, but that means the drag link has been running on that angle, which may have prematurely worn out the ends.
I just did the drag link on my K5. If you end up getting new drag link ends Summit has the Moog ends for less than vato-zone sells the cheapies.
__________________
'80 SRW C35 - 355/700R4/4:11/2.5-3/DD
'77 Cheyenne K5 - Roller cam 355/NV4500/205/4:88's/35's/DD

rust repair on the '77
http://67-72chevytrucks.com/vboard/s...d.php?t=740291

Last edited by mickeykreg; 02-24-2014 at 05:47 PM. Reason: meant summit, not rock auto
mickeykreg is offline   Reply With Quote
Old 02-25-2014, 12:38 AM   #9
swissarmychainsaw
Registered User
 
Join Date: Jun 2009
Location: san francisco, ca (east bay)
Posts: 674
Re: Unlifting project.

How good does this thing go down the road? Does it tend to wander a bit?
I think you put new tires on right?

I agree that the Pitman arm looks stock.
All the front end components are easy to change out. I just did this on my 2wd and I used Rockauto.com (by far the cheapest you will find) and Napa, which actually has stuff in stock for my 1975! bam!

Regarding the brake lines, both the front and rear will be longer for the lift.
(now's a REALLY good time to replace them). Cheap and in stock from Oreillys, but consider steel lines, depending on your budget.

If you are considering selling the lift kit, (if your parking brake works) it will also need to be longer for the lift (you might include the P-Brake lines in the sale).

You have blocks in the rear, but what is lifting the front? All Springs?

You are going to be happy with this!
swissarmychainsaw is offline   Reply With Quote
Old 02-25-2014, 12:54 AM   #10
eighteenninetytwo
Registered User
 
Join Date: Sep 2013
Location: Redwood city, CA
Posts: 694
Re: Unlifting project.

It does wander when driving straight (or trying to) despite brand new tires. Recently put new brake lines on the front will i have to change them again? I assume I'll have to shorten the parking brake cable when the lift is removed also. Front is spring lift so I have to change them out. What does NAPA have in stock for 75's a sthere is one downtown i found this weekend and I have a 75.
eighteenninetytwo is offline   Reply With Quote
Old 02-25-2014, 01:16 AM   #11
swissarmychainsaw
Registered User
 
Join Date: Jun 2009
Location: san francisco, ca (east bay)
Posts: 674
Re: Unlifting project.

Quote:
Originally Posted by eighteenninetytwo View Post
It does wander when driving straight (or trying to) despite brand new tires. Recently put new brake lines on the front will i have to change them again? I assume I'll have to shorten the parking brake cable when the lift is removed also. Front is spring lift so I have to change them out. What does NAPA have in stock for 75's a sthere is one downtown i found this weekend and I have a 75.
My 2wd was a mess and new tires and new Pitman & Idler & tie rod ends fixed it.
Originally I was only going to do the Pitman and Idler, but when I was in there taking it all apart I asked myself "why am I not doing all of these while I'm in here?". Napa had the tie rod ends in stock. The local one to me has been really awesome. Nice folks, and they even give me price breaks. It simply shames the local O'reillys.

I assume that you can leave the longer brake lines in.

Having done this kind of stuff for the first time, let me say it's really not as bad as it seems.
swissarmychainsaw is offline   Reply With Quote
Old 02-25-2014, 01:36 AM   #12
imjeff
Registered User
 
imjeff's Avatar
 
Join Date: Feb 2008
Location: Tacoma Washington
Posts: 890
Re: Unlifting project.

In the rear it is typical to have a small bracket that raises the section of brake line with the tee about 3" above the pumpkin. The steering arm looks stock and I'd leave it alone unless it is bad. Same with the drag link.. The front brake lines are probably stock as well. Not too many people actually change the front brake lines with the lift. Even if they did, unless they rub somewhere, longer is better than shorter. I'd put new shackles on all four corners while you have it apart. They stretch a fair amount under torque and fatigue over time. Any spring shop can hook you up. Front springs are all over. I've left several sets behind over the years so they should be easy to find.

Good luck!

Jeff
__________________
I know a guy who's addicted to brake fluid. He says he can stop any time.
72 K10 396
75 Cj5 MPI 350 Chev
67 Chevelle 396, 4 speed
74 FXE
08 Tahoe
imjeff is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:35 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com