Pinion Seal? maybe? i dunno! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Prerunner1982 · 08-18-2003, 03:22 AM

ok.. my truck has been leaking gear fluid from where the driveshaft meets the axle..... how hard is this to fix/replace?

RockHQ · 08-18-2003, 09:40 AM

Haven't really looked into this but as far as i know you'll need a new crush sleeve for the pinion to set the correct pinion preload after you take off the yoke for the driveshaft. That, and a LONG extention bar to get the pinion nut off. Someone with more experience will most likely chime in.

Txstruck · 08-18-2003, 05:21 PM

RockHQ said it correctly, but be sure to use a torque wrench when putting the pinon nut back on as to not throw the pinion/ring gear out of whack. I had to replace mine and it took les than an hour. If I remember corectly, you will have to tap the new crush sleeve in place.

God luck! and have fun. Its not too bad

Prerunner1982 · 08-19-2003, 02:46 AM

will have to look at it more before i decide to do it. never messed with an axle that much before, and being my only working vehicle at the moment, i cant afford to have it down for more than a few hrs. thanks guys

loweredd · 08-19-2003, 02:45 PM

Isnt there a torque spec for using an old crush sleeve? I thought I saw that somewhere before???

RockHQ · 08-19-2003, 04:31 PM

I don't think a torque spec for a used sleeve will do any good, the crush sleeve is...well, meant to crush when you tighten the pinion and gives a correct preload that way?

jimfulco · 08-21-2003, 11:41 AM

Don't forget the torque to turn is in INCH-pounds. The torque spec difference is from new bearings to used bearings.

08-18-2003, 03:22 AM	#1
Prerunner1982 Registered User Join Date: Oct 2002 Location: Edmond, OK Posts: 5,904	Pinion Seal? maybe? i dunno! ok.. my truck has been leaking gear fluid from where the driveshaft meets the axle..... how hard is this to fix/replace? __________________ Jon 1982 Chevy Silverado 350/th350.... RETIRED 1993 Jeep XJ 2 door(Cherokee) 4wd 4.0ltr/AX-15 (5spd)/NP231 .... Oklahoma Roll Call

08-18-2003, 09:40 AM	#2
RockHQ ROCKET POWER! Join Date: Feb 2003 Location: Finland, Europe Posts: 509	Haven't really looked into this but as far as i know you'll need a new crush sleeve for the pinion to set the correct pinion preload after you take off the yoke for the driveshaft. That, and a LONG extention bar to get the pinion nut off. Someone with more experience will most likely chime in. __________________ What did i do last nite? I had a wonderful time, That's what they tell me What did i do last nite? 1979 C-10 shortfleet: Olds 350, Th400, 12 bolt Current project: 1969 Olds 455 W-30, needing a rebuild

08-18-2003, 05:21 PM	#3
Txstruck Registered User Join Date: Nov 2002 Location: Dallas Posts: 459	RockHQ said it correctly, but be sure to use a torque wrench when putting the pinon nut back on as to not throw the pinion/ring gear out of whack. I had to replace mine and it took les than an hour. If I remember corectly, you will have to tap the new crush sleeve in place. God luck! and have fun. Its not too bad __________________ Steve 86 K30 4x4 6.2L Diesel\TH400\NP208 - 14bolt FF rear w/detroit locker and Dana60 front w/detroit locker- both with 4.56 gears "Runs on Mud"

08-19-2003, 02:46 AM	#4
Prerunner1982 Registered User Join Date: Oct 2002 Location: Edmond, OK Posts: 5,904	will have to look at it more before i decide to do it. never messed with an axle that much before, and being my only working vehicle at the moment, i cant afford to have it down for more than a few hrs. thanks guys __________________ Jon 1982 Chevy Silverado 350/th350.... RETIRED 1993 Jeep XJ 2 door(Cherokee) 4wd 4.0ltr/AX-15 (5spd)/NP231 .... Oklahoma Roll Call

08-19-2003, 04:31 PM	#6
RockHQ ROCKET POWER! Join Date: Feb 2003 Location: Finland, Europe Posts: 509	I don't think a torque spec for a used sleeve will do any good, the crush sleeve is...well, meant to crush when you tighten the pinion and gives a correct preload that way? __________________ What did i do last nite? I had a wonderful time, That's what they tell me What did i do last nite? 1979 C-10 shortfleet: Olds 350, Th400, 12 bolt Current project: 1969 Olds 455 W-30, needing a rebuild

08-19-2003, 02:45 PM	#5
loweredd www.loweredd.com Join Date: Aug 2002 Location: Struble IA Posts: 808	Isnt there a torque spec for using an old crush sleeve? I thought I saw that somewhere before???

08-21-2003, 11:41 AM	#7
jimfulco Registered User Join Date: May 2003 Location: Shreveport LA Posts: 3,170	Don't forget the torque to turn is in INCH-pounds. The torque spec difference is from new bearings to used bearings.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.