S10 hitch for 55-59 trucks? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

yossarian19 · 10-03-2015, 02:28 PM

I was looking around for vehicles with a 34" frame width.
I know the Chevy Venture hitch works on a TF truck, but I wanted something rated heavier.
The Crown Victoria hitch is a maybe, I know the front section is the same width as a TF but not sure about the rear.
The S10, I think, has the same rear frame width -- anyone looked at it any closer? Would be nice to put at least a 7500 lb hitch on the truck.

**G&R's57GMC** · 10-03-2015, 04:28 PM

Use the U Haul receiver for the Chevy Venture and add side plates to mount it to the sides of the frame and add a tube going forward to a second cross member that is also plated to the sides of the frame rails.

This will spread the load over a longer portion of the truck frame.

It wouldn't hurt to box the frame rails also.

What are you planning to tow that you need this much receiver for ?

OrrieG · 10-03-2015, 07:45 PM

I found a used Draw Tite Class 3 that mounts to the bottom of the frame. Rear most bolts were ok but front a problem. I just welded on some side plates to distribute the load along the frame. The receiver tucks right under the bumper.

**Dan in Pasadena** · 10-03-2015, 07:49 PM

Nice pics Glen!

**mr48chev** · 10-03-2015, 08:53 PM

That last one comes under the heading of "will handle far more than the truck will".

You still have to stay within what the donor S-10 chassis was rated at for towing and that is probably some where between 3000 and 5500 lbs depending on what year and chassis.

**G&R's57GMC** · 10-04-2015, 12:17 AM

Quote:

Originally Posted by Dan in Pasadena

Nice pics Glen!

Thanks Dan.

To The O.P. The Venture receiver is rated at 3500# with 350# Tongue weight.

Besides the TF Frame is not robust enough for a 7500# trailer.

yossarian19 · 10-04-2015, 12:37 AM

Quote:

Originally Posted by G&R's57GMC

Thanks Dan.

To The O.P. The Venture receiver is rated at 3500# with 350# Tongue weight.

Besides the TF Frame is not robust enough for a 7500# trailer.

You think? I hadn't even thought of the frame as a limiting factor.
I have an '04 Grand Cherokee, rated to 7500 lbs, that I would like to downsize. I'd like to be able to pull a project home, though, which leaves the truck. 3,500# doesn't cut it. 5,000# might but more would obviously be better.

**G&R's57GMC** · 10-04-2015, 12:43 AM

Ah ... This could be posable with the additions I mentioned above .

Just be sure the load on the trailer is balanced over the trailer axles.

10-03-2015, 02:28 PM	#1
yossarian19 Registered User Join Date: Sep 2011 Location: Nevada City, CA Posts: 908	S10 hitch for 55-59 trucks? I was looking around for vehicles with a 34" frame width. I know the Chevy Venture hitch works on a TF truck, but I wanted something rated heavier. The Crown Victoria hitch is a maybe, I know the front section is the same width as a TF but not sure about the rear. The S10, I think, has the same rear frame width -- anyone looked at it any closer? Would be nice to put at least a 7500 lb hitch on the truck. __________________ "Over my head" 1957 Chevy 3200, big rear window & 6 lug. Front disc, power steering, Vortec 4.8 / 4L60E swap, hydro boost brakes & patina.

10-03-2015, 04:28 PM	#2
G&R's57GMC Senior Member Join Date: Aug 2010 Location: Shasta Lake, CA. Posts: 1,624	Re: S10 hitch for 55-59 trucks? Use the U Haul receiver for the Chevy Venture and add side plates to mount it to the sides of the frame and add a tube going forward to a second cross member that is also plated to the sides of the frame rails. This will spread the load over a longer portion of the truck frame. It wouldn't hurt to box the frame rails also. What are you planning to tow that you need this much receiver for ? Attached Images __________________ Glen & Jane's Rides ‘57 GMC NAPCO Long Bed V8 4 speed Bought 2008 7 other cars & trucks , 5 trailers '56 Chevy Long Bed I6, 4 speed Bought 1990 Sold 8.22.2020 ’56 GMC Suburban Pickup V8, 4 speed Hydramatic Bought 1996 Sold 10.11.2020 My Other Tinkerings http://67-72chevytrucks.com/vboard/s...75#post8967275 Last edited by G&R's57GMC; 10-03-2015 at 04:43 PM.

10-03-2015, 07:45 PM	#3
OrrieG Registered User Join Date: Jun 2006 Location: Idaho Posts: 8,800	Re: S10 hitch for 55-59 trucks? I found a used Draw Tite Class 3 that mounts to the bottom of the frame. Rear most bolts were ok but front a problem. I just welded on some side plates to distribute the load along the frame. The receiver tucks right under the bumper. Attached Images __________________ 1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project

10-03-2015, 07:49 PM	#4
Dan in Pasadena Senior Member Join Date: Nov 2008 Location: Glendora, CA Posts: 6,344	Re: S10 hitch for 55-59 trucks? Nice pics Glen! __________________ '55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda!

10-03-2015, 08:53 PM	#5
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,711	Re: S10 hitch for 55-59 trucks? That last one comes under the heading of "will handle far more than the truck will". You still have to stay within what the donor S-10 chassis was rated at for towing and that is probably some where between 3000 and 5500 lbs depending on what year and chassis. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

10-04-2015, 12:43 AM	#8
G&R's57GMC Senior Member Join Date: Aug 2010 Location: Shasta Lake, CA. Posts: 1,624	Re: S10 hitch for 55-59 trucks? Ah ... This could be posable with the additions I mentioned above . Just be sure the load on the trailer is balanced over the trailer axles. __________________ Glen & Jane's Rides ‘57 GMC NAPCO Long Bed V8 4 speed Bought 2008 7 other cars & trucks , 5 trailers '56 Chevy Long Bed I6, 4 speed Bought 1990 Sold 8.22.2020 ’56 GMC Suburban Pickup V8, 4 speed Hydramatic Bought 1996 Sold 10.11.2020 My Other Tinkerings http://67-72chevytrucks.com/vboard/s...75#post8967275

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.