Front suspension drop failure - The 1947 - Present Chevrolet & GMC Truck Message Board Network

65standard · 10-11-2015, 08:10 AM

I have 2 1/2" drop spindles and cut 2 full coils off the stock C/10 springs. Truck is fully bottomed out with tires resting on the top of the inner fenders. Clearly 2 coils is way too much. Time for new springs.

sic_F44 · 10-11-2015, 09:28 AM

looks good tho id just pull the inners for now lol

**Gregski** · 10-11-2015, 10:45 AM

Quote:

Originally Posted by 65standard

I have 2 1/2" drop spindles and cut 2 full coils off the stock C/10 springs. Truck is fully bottomed out with tires resting on the top of the inner fenders. Clearly 2 coils is way too much. Time for new springs.

You shouldn't be cutting coil springs to begin with.

kalbert · 10-11-2015, 11:07 AM

Nah... Cutting springs is fine. Do it with a sawzall or cutoff wheel, not a torch and you'll be fine. 2 full coils is pretty aggressive, most people do just one and get around 2" of ride height with a moderately stiffer ride. Chopping a coil off and relocating the shackles and hangers is a near zero cost way to get lower.

Burmanater · 10-11-2015, 12:03 PM

You might want to try a smaller size tire. That's the way my truck sits and ive got a 225/70 15 and it still rubs on hard cornering. had a set of 225 75 15s up front and it was about the same but rubbed a tad more(Hercules terra trac) I had 225 75 bfg ta tires that for some reason didn't rub though.

SkinnyG · 10-11-2015, 12:29 PM

If you're buying springs, buy 1-ton springs. It adds spring rate so you can ride low with less bottoming out --- but only cut a coil or so off (I cut a coil, then kept trimming 2" off the end until it sat at the height I wanted).

mcmlxix · 10-11-2015, 03:18 PM

Quote:

Originally Posted by SkinnyG

If you're buying springs, buy 1-ton springs. It adds spring rate so you can ride low with less bottoming out --- but only cut a coil or so off (I cut a coil, then kept trimming 2" off the end until it sat at the height I wanted).

MOOG 6452 1/2 ton
Bar Diameter - Inches 0.78
End Type 1 Tangential
End Type 2 Pigtail
Free Height - Inches 13.64
ID - Inches 3.68
Installation Height - Inches 10.00
Load - lbs 3155.00
Spring Rate - lbs per inch 843.00
Spring Type Constant Rate
Alternate/OEM Part Number(s): 328096, 328097, 328150, 328151, 3933259

MOOG 6454 1 ton
Bar Diameter - Inches 0.82
End Type 1 Tangential
End Type 2 Pigtail
Free Height - Inches 13.61
ID - Inches 3.67
Installation Height - Inches 10.00
Load - lbs 3841.00
Spring Rate - lbs per inch 1060.00
Spring Type Constant Rate
Alternate/OEM Part Number(s): 328098, 328099, 328100

muthstryker · 10-11-2015, 03:28 PM

1 coil on stock springs is a 2" drop. You cut a tad to much lol

Major86 · 10-11-2015, 03:55 PM

How much drop is 1 coil off drop springs? 2" as well?

muthstryker · 10-11-2015, 04:39 PM

Probably 1", drop springs have more coils with a higher spring rate.

65standard · 10-11-2015, 06:02 PM

Thanks everyone. I just bought the Moog 6454 springs from SummitRacing. Couldn't beat the price, $8.97 a pair plus shipping. Must be a mistake, but I bought them before they see it. The cheapest Moog 6452 springs I found are $69. One-ton springs it is.

mcmlxix · 10-11-2015, 07:10 PM

Quote:

Originally Posted by 65standard

Thanks everyone. I just bought the Moog 6454 springs from SummitRacing. Couldn't beat the price, $8.97 a pair plus shipping. Must be a mistake, but I bought them before they see it. The cheapest Moog 6452 springs I found are $69. One-ton springs it is.

Holy OOPS Batman ... I ordered a set too and I don't even need them right now... I though you had a typo in your post till I checked out the site...

RUN GMC · 10-12-2015, 02:14 AM

In for a set just because........thanks for the heads up.............

school boy · 10-12-2015, 09:39 AM

Bought a set myself! $15 shipped is a steal! Glad I looked into this!

Joe69C10 · 10-12-2015, 10:48 AM

Great deal! I just ordered a set for $14.92 shipped! Im in the process of dropping my truck and was gonna cut the old rusty stockers..

Domer · 10-12-2015, 12:28 PM

all you people ordering them.. now they show ship today, but when you check out, they say back ordered with an estimated ship date of Nov. 5

65standard · 10-12-2015, 03:39 PM

They had 10 pairs available when I ordered mine.

ddr11 · 10-12-2015, 03:40 PM

There is a easier and cheaper fix for this. I've been running this set up for a while now. AFCO makes a coil spring spacer/adjuster for the dirt track application. This also works very well when your truck doesn't sit level across the front

Tom · 10-12-2015, 05:31 PM

^ Thats a good find, something to remember for down the road when needed.

mcmlxix · 10-13-2015, 05:21 AM

Quote:

Originally Posted by mcmlxix

Holy OOPS Batman ... I ordered a set too and I don't even need them right now... I though you had a typo in your post till I checked out the site...

Mine are scheduled to arrive today on the 13th.....

Shugalou · 10-13-2015, 09:10 AM

damn they are still there

http://www.summitracing.com/int/parts/mog-6454

I thought about buying but I would prefer a drop spring - damn good price though

solidaxel · 10-13-2015, 11:42 AM

I could not resist!
I need to change one spring, front end is sitting 3/4" lower on the passenger side, so I guess I will change two at that price!

solidaxel · 10-13-2015, 11:44 AM

Quote:

Originally Posted by mcmlxix

Mine are scheduled to arrive today on the 13th.....

When you receive them would you check the static height (length), Thanks

65standard · 10-13-2015, 07:35 PM

Mine were delivered today.

gasmn1620 · 10-14-2015, 08:43 AM

just got some.... don't really need them but you never know when you will, and at 14.92 you can't go wrong.

10-11-2015, 08:10 AM	#1
65standard Registered User Join Date: Dec 2014 Location: Coal City, IL Posts: 695	Front suspension drop failure I have 2 1/2" drop spindles and cut 2 full coils off the stock C/10 springs. Truck is fully bottomed out with tires resting on the top of the inner fenders. Clearly 2 coils is way too much. Time for new springs. Attached Images __________________ Tony Nicholas @ Midwest Metal Masters 1953 Chevy 3100 392 Hemi w/727 & 9” Ford 1985 Chevy C/10 6.0L 4L80 373 locker

10-11-2015, 09:28 AM	#2
sic_F44 Registered User Join Date: Aug 2014 Location: Hickory, North Carolina Posts: 14	Re: Front suspension drop failure looks good tho id just pull the inners for now lol

10-11-2015, 11:07 AM	#4
kalbert Registered User Join Date: Jun 2012 Location: Minnesota Posts: 509	Re: Front suspension drop failure Nah... Cutting springs is fine. Do it with a sawzall or cutoff wheel, not a torch and you'll be fine. 2 full coils is pretty aggressive, most people do just one and get around 2" of ride height with a moderately stiffer ride. Chopping a coil off and relocating the shackles and hangers is a near zero cost way to get lower.

10-11-2015, 12:03 PM	#5
Burmanater Registered User Join Date: Mar 2014 Location: Pandora, Ohio Posts: 56	Re: Front suspension drop failure You might want to try a smaller size tire. That's the way my truck sits and ive got a 225/70 15 and it still rubs on hard cornering. had a set of 225 75 15s up front and it was about the same but rubbed a tad more(Hercules terra trac) I had 225 75 bfg ta tires that for some reason didn't rub though.

10-11-2015, 12:29 PM	#6
SkinnyG Registered User Join Date: Feb 2012 Location: Beautiful BC, Canada, eh?! Posts: 2,267	Re: Front suspension drop failure If you're buying springs, buy 1-ton springs. It adds spring rate so you can ride low with less bottoming out --- but only cut a coil or so off (I cut a coil, then kept trimming 2" off the end until it sat at the height I wanted). __________________ 1961 Apache: "Grabber Orange" Shortboxed, pancake, step-notch, air-ride, turbo, LS 1977 Silverado: Shortboxed & dropped, potato-potato V8 Pontiac Firefly (Chevy Sprint): The ultimate engine swap: 5.7L in a 1.0L bag Lotus Super 7 Replica: Scratch-built street-legal rollerskate

10-11-2015, 03:28 PM	#8
muthstryker Registered User Join Date: Dec 2009 Location: Snohomish, Washington Posts: 1,187	Re: Front suspension drop failure 1 coil on stock springs is a 2" drop. You cut a tad to much lol __________________ Matt

10-11-2015, 03:55 PM	#9
Major86 Registered User Join Date: Sep 2015 Location: Martin, TN Posts: 64	Re: Front suspension drop failure How much drop is 1 coil off drop springs? 2" as well?

10-11-2015, 04:39 PM	#10
muthstryker Registered User Join Date: Dec 2009 Location: Snohomish, Washington Posts: 1,187	Re: Front suspension drop failure Probably 1", drop springs have more coils with a higher spring rate. __________________ Matt

10-11-2015, 06:02 PM	#11
65standard Registered User Join Date: Dec 2014 Location: Coal City, IL Posts: 695	Re: Front suspension drop failure Thanks everyone. I just bought the Moog 6454 springs from SummitRacing. Couldn't beat the price, $8.97 a pair plus shipping. Must be a mistake, but I bought them before they see it. The cheapest Moog 6452 springs I found are $69. One-ton springs it is. __________________ Tony Nicholas @ Midwest Metal Masters 1953 Chevy 3100 392 Hemi w/727 & 9” Ford 1985 Chevy C/10 6.0L 4L80 373 locker

10-12-2015, 02:14 AM	#13
RUN GMC Registered User Join Date: May 2014 Location: North AL Posts: 363	Re: Front suspension drop failure In for a set just because........thanks for the heads up............. __________________ http://i204.photobucket.com/albums/b...baae5d9a7e.jpg

10-12-2015, 09:39 AM	#14
school boy Registered User Join Date: Apr 2012 Location: Loretto Ky Posts: 318	Re: Front suspension drop failure Bought a set myself! $15 shipped is a steal! Glad I looked into this!

10-12-2015, 10:48 AM	#15
Joe69C10 Registered User Join Date: Jul 2012 Location: Ocala,FL Posts: 129	Re: Front suspension drop failure Great deal! I just ordered a set for $14.92 shipped! Im in the process of dropping my truck and was gonna cut the old rusty stockers..

10-12-2015, 12:28 PM	#16
Domer Registered User Join Date: Mar 2013 Location: Lakeside, Ca. Posts: 320	Re: Front suspension drop failure all you people ordering them.. now they show ship today, but when you check out, they say back ordered with an estimated ship date of Nov. 5 __________________ Project Roxy... Shes Bad, Low, and Blown... http://67-72chevytrucks.com/vboard/s...d.php?t=673333 Last edited by Domer; 10-12-2015 at 12:33 PM.

10-12-2015, 03:39 PM	#17
65standard Registered User Join Date: Dec 2014 Location: Coal City, IL Posts: 695	Re: Front suspension drop failure They had 10 pairs available when I ordered mine. __________________ Tony Nicholas @ Midwest Metal Masters 1953 Chevy 3100 392 Hemi w/727 & 9” Ford 1985 Chevy C/10 6.0L 4L80 373 locker

10-12-2015, 03:40 PM	#18
ddr11 Registered User Join Date: Nov 2013 Location: sumter sc Posts: 79	Re: Front suspension drop failure There is a easier and cheaper fix for this. I've been running this set up for a while now. AFCO makes a coil spring spacer/adjuster for the dirt track application. This also works very well when your truck doesn't sit level across the front Attached Images



Register or Log In To remove these advertisements.

10-12-2015, 05:31 PM	#19
Tom driving is in my blood Join Date: Dec 1999 Location: Mesa AZ Posts: 5,748	Re: Front suspension drop failure ^ Thats a good find, something to remember for down the road when needed. __________________ -78 c10 short/step: 388cid, M20, 5/5 drop, lots more. Playtoy and first vehicle. -98 c1500 x-cab: 5.7L, 17" rims, 5/6 drop, flowmaster, helper bags,NBS rear disk brakes. -02 Suburban 4x4: leveled front -CBR600F4i, CBR600RR, CBR1000RR, and standup skis DISCLAIMER: I cant spell for the life of me.

10-13-2015, 09:10 AM	#21
Shugalou Registered User Join Date: Jan 2013 Location: Toronto, ON Posts: 458	Re: Front suspension drop failure damn they are still there http://www.summitracing.com/int/parts/mog-6454 I thought about buying but I would prefer a drop spring - damn good price though __________________ Found my dad's old truck http://67-72chevytrucks.com/vboard/s...d.php?t=563321 Newspaper Article Publishing the quest find my dad's old truck http://www.theglobeandmail.com/globe...ticle12494281/

10-13-2015, 11:42 AM	#22
solidaxel Registered User Join Date: Dec 2002 Location: Cactus Patch So. Az Posts: 4,749	Re: Front suspension drop failure I could not resist! I need to change one spring, front end is sitting 3/4" lower on the passenger side, so I guess I will change two at that price! __________________ 53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42

10-13-2015, 07:35 PM	#24
65standard Registered User Join Date: Dec 2014 Location: Coal City, IL Posts: 695	Re: Front suspension drop failure Mine were delivered today. __________________ Tony Nicholas @ Midwest Metal Masters 1953 Chevy 3100 392 Hemi w/727 & 9” Ford 1985 Chevy C/10 6.0L 4L80 373 locker

10-14-2015, 08:43 AM	#25
gasmn1620 Registered User Join Date: Oct 2014 Location: panama city, fl Posts: 204	Re: Front suspension drop failure just got some.... don't really need them but you never know when you will, and at 14.92 you can't go wrong.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.