Wanted, Holley 600, or parts only. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

RON WOODGEARD · 10-21-2003, 05:42 PM

I could use a Holley 600 square bore, 1850 ( i think) Single inlet vacuum secondaries.

I need one for Parts Only, I have one now that has a bad base plate, The butterfly plate shaft is worn out. I bought a Bunch, of aftermarket "goodies" for it, and it sits under the bench for a couple of years, Actually, I forgot about it, til the move.

If you have a good base plate or a parts carb reasonable, e-mail or PM me.

Ron

woodgeard@earthlink.net

red71cheyenne · 10-21-2003, 08:11 PM

I have a holley in the garage that needs rebuilding, but have no idea what size or model it is. You are welcome to it. Jeff.

RON WOODGEARD · 10-22-2003, 07:09 AM

Let me know price, Shipping cost.

I guess there's always a chance.

Ron

I'm at 89410

red71cheyenne · 10-22-2003, 12:37 PM

I'll pull it out and take a pic of it and see if I can find any numbers on it for you. Jeff.

Destructo · 10-22-2003, 12:43 PM

I have a 600cfm, vacuum secondary carb with single fuel inlet. I think its a 1460 model. Seems like it ran alright when I put it on an engine but could probably use a rebuild if you were gonna use it in itself. Which parts do you need?

Sent you a pm

10-21-2003, 05:42 PM	#1
RON WOODGEARD Resident Young Old Dude ! Join Date: Jul 2001 Location: Nevada Posts: 1,948	Wanted, Holley 600, or parts only. I could use a Holley 600 square bore, 1850 ( i think) Single inlet vacuum secondaries. I need one for Parts Only, I have one now that has a bad base plate, The butterfly plate shaft is worn out. I bought a Bunch, of aftermarket "goodies" for it, and it sits under the bench for a couple of years, Actually, I forgot about it, til the move. If you have a good base plate or a parts carb reasonable, e-mail or PM me. Ron woodgeard@earthlink.net

10-21-2003, 08:11 PM	#2
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	I have a holley in the garage that needs rebuilding, but have no idea what size or model it is. You are welcome to it. Jeff. __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

10-22-2003, 12:37 PM	#4
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	I'll pull it out and take a pic of it and see if I can find any numbers on it for you. Jeff. __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

10-22-2003, 12:43 PM	#5
Destructo Registered User Join Date: Sep 2003 Location: Lewisville, NC Posts: 1,836	I have a 600cfm, vacuum secondary carb with single fuel inlet. I think its a 1460 model. Seems like it ran alright when I put it on an engine but could probably use a rebuild if you were gonna use it in itself. Which parts do you need? Sent you a pm Last edited by Destructo; 10-22-2003 at 12:47 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-22-2003, 07:09 AM	#3
RON WOODGEARD Resident Young Old Dude ! Join Date: Jul 2001 Location: Nevada Posts: 1,948	Let me know price, Shipping cost. I guess there's always a chance. Ron I'm at 89410



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.