66 C10 Dual Exhaust Routing Photos w/396 bbc - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Afirehawk1 · 09-21-2019, 03:43 PM

Need some input on how to run dual exhaust on this truck.
Going with 2.5 pipe with either Flowmaster or Magnaflow

**The Rocknrod** · 09-21-2019, 06:03 PM

Here is a 2.5" Exhaust route as an example. Not mine.

65c10restomod · 09-22-2019, 11:08 AM

looks dangerously close to bed wood and gas tank

AcampoDave · 09-22-2019, 01:59 PM

Quote:

Originally Posted by 65c10restomod

looks dangerously close to bed wood and gas tank

I once had that same impression about my own exhaust. Turns out it wasn't a big deal back then and it's still not. Here's the thread...
http://67-72chevytrucks.com/vboard/s...d.php?t=779407

**The Rocknrod** · 09-22-2019, 02:11 PM

Ya those cross members in the bed are how deep? I'm doing closely the same thing only with 2.25 pipes. Since I get under there with the installer . . The only place that will the closest will be over the rear axle still leaving almost an inch and with DEI Flexible Pipe Shield there I'm concerned - Not.

Afirehawk1 · 09-22-2019, 02:45 PM

Noticed pipe hangers and hardware
Any good sources?

AcampoDave · 09-22-2019, 05:11 PM

This thread shows how mine is routed on the outside of the frame rails. I was addressing resonance but I uploaded some decent pics. Having a manual tranny with the old cast iron bell housing puts another crossmember smack dab in the way for an inside job.
http://67-72chevytrucks.com/vboard/s...d.php?t=792007

09-21-2019, 03:43 PM	#1
Afirehawk1 Registered User Join Date: Feb 2016 Location: Valrico, Florida Posts: 661	66 C10 Dual Exhaust Routing Photos w/396 bbc Need some input on how to run dual exhaust on this truck. Going with 2.5 pipe with either Flowmaster or Magnaflow

09-21-2019, 06:03 PM	#2
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: 66 C10 Dual Exhaust Routing Photos w/396 bbc Here is a 2.5" Exhaust route as an example. Not mine. Attached Images __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

09-22-2019, 11:08 AM	#3
65c10restomod Registered User Join Date: Sep 2012 Location: earth Posts: 93	Re: 66 C10 Dual Exhaust Routing Photos w/396 bbc looks dangerously close to bed wood and gas tank

09-22-2019, 02:11 PM	#5
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: 66 C10 Dual Exhaust Routing Photos w/396 bbc Ya those cross members in the bed are how deep? I'm doing closely the same thing only with 2.25 pipes. Since I get under there with the installer . . The only place that will the closest will be over the rear axle still leaving almost an inch and with DEI Flexible Pipe Shield there I'm concerned - Not. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

09-22-2019, 02:45 PM	#6
Afirehawk1 Registered User Join Date: Feb 2016 Location: Valrico, Florida Posts: 661	Re: 66 C10 Dual Exhaust Routing Photos w/396 bbc Noticed pipe hangers and hardware Any good sources?

09-22-2019, 05:11 PM	#7
AcampoDave Registered User Join Date: Feb 2013 Location: central California Posts: 2,776	Re: 66 C10 Dual Exhaust Routing Photos w/396 bbc This thread shows how mine is routed on the outside of the frame rails. I was addressing resonance but I uploaded some decent pics. Having a manual tranny with the old cast iron bell housing puts another crossmember smack dab in the way for an inside job. http://67-72chevytrucks.com/vboard/s...d.php?t=792007

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.