Rear bumper bracket holes - The 1947 - Present Chevrolet & GMC Truck Message Board Network

focusedontheprize · 01-28-2020, 10:45 PM

I am currently fixing the rear frame rails on my ‘88 V30. I noticed that I have two sets of rear bumper bracket holes (1 1/4” apart) for my sport bumper. Could anyone recommend which set I should be using? I trimmed the rear frame rail, but can add material back if I should be using the front set. Thanks.

focusedontheprize · 01-29-2020, 09:46 PM

Anyone able to help with this?

RUN GMC · 01-29-2020, 10:19 PM

Quote:

Originally Posted by focusedontheprize

Anyone able to help with this?

In this video I remember the fabricator talking about two sets of holes and which ones to use according to year......good info that might can help you......

https://www.youtube.com/watch?v=AvfLJ0m0GE8

focusedontheprize · 01-30-2020, 11:33 PM

Quote:

Originally Posted by RUN GMC

In this video I remember the fabricator talking about two sets of holes and which ones to use according to year......good info that might can help you......

https://www.youtube.com/watch?v=AvfLJ0m0GE8

Thank you for this. I will have to check the channel and video out.

focusedontheprize · 02-09-2020, 07:16 PM

Quote:

Originally Posted by RUN GMC

In this video I remember the fabricator talking about two sets of holes and which ones to use according to year......good info that might can help you......

https://www.youtube.com/watch?v=AvfLJ0m0GE8

Thanks again for sending this link. Unfortunately in this video they cut out the forward bolt holes that are used for the tow hitch (which I am using).

Can anyone provide a measurement from the rear edge of the frame rail to their bolt holes?

SCOTI · 02-16-2020, 02:11 PM

I got some pics for you from my dually. I added some text to help w/the numbers. 1, 2, & 3 are the bolts that retain the inner & outer brackets on mine.

#3 is approx. 5" from the edge of the frame rail & only goes through the last hole on the inner/longer bracket.
#2 is approx. 1.5" from the edge of the frame rail.
#1 & #2 go through both inner & outer brackets.

focusedontheprize · 02-20-2020, 09:43 AM

Quote:

Originally Posted by SCOTI

I got some pics for you from my dually. I added some text to help w/the numbers. 1, 2, & 3 are the bolts that retain the inner & outer brackets on mine.

#3 is approx. 5" from the edge of the frame rail & only goes through the last hole on the inner/longer bracket.
#2 is approx. 1.5" from the edge of the frame rail.
#1 & #2 go through both inner & outer brackets.

Thank you very much SCOTI! Neither of the set of holes reflect those dimensions, so I am going to plug weld them and probably have to start fresh. I appreciate the information.

02-16-2020, 02:11 PM	#6
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,066	Re: Rear bumper bracket holes I got some pics for you from my dually. I added some text to help w/the numbers. 1, 2, & 3 are the bolts that retain the inner & outer brackets on mine. #3 is approx. 5" from the edge of the frame rail & only goes through the last hole on the inner/longer bracket. #2 is approx. 1.5" from the edge of the frame rail. #1 & #2 go through both inner & outer brackets. Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-28-2020, 10:45 PM	#1
focusedontheprize Registered User Join Date: Feb 2012 Location: CA Posts: 846	Rear bumper bracket holes I am currently fixing the rear frame rails on my ‘88 V30. I noticed that I have two sets of rear bumper bracket holes (1 1/4” apart) for my sport bumper. Could anyone recommend which set I should be using? I trimmed the rear frame rail, but can add material back if I should be using the front set. Thanks. Attached Images __________________ "Dixie" - 1988 Chevrolet V30 CC DRW "3+3" \| 7.4L 454 (L19) \| TH400 \| 4" lift \| 35"s "Lucille" - 1949 Chevrolet 3100 (on hold)

01-29-2020, 09:46 PM	#2
focusedontheprize Registered User Join Date: Feb 2012 Location: CA Posts: 846	Re: Rear bumper bracket holes Anyone able to help with this? __________________ "Dixie" - 1988 Chevrolet V30 CC DRW "3+3" \| 7.4L 454 (L19) \| TH400 \| 4" lift \| 35"s "Lucille" - 1949 Chevrolet 3100 (on hold)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.