patina question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**65truckowner** · 12-05-2021, 07:23 PM

I am building a 1965 c10 patina. My drivers side fender is really rough Should I cut out the bad and patch then primer or just bolt it on. Here is a picture of the truck and the fender.

IMG_4611 by Daniel Crymes, on Flickr

IMG_4610 by Daniel Crymes, on Flickr

Billy Stuck · 12-05-2021, 07:33 PM

I'd be tempted to fix the rust, go a bit smoother on the wrinkles, and then fauxtina it back.

**jocko** · 12-05-2021, 08:14 PM

that's a bit beyond patina, I'm with Billy.

**65truckowner** · 12-05-2021, 09:13 PM

That is what I was thinking as well

**cwcarpenter98** · 12-05-2021, 10:33 PM

I'll third Billy. Since you already have to fauxtina the rockers, the fender would look better that way too

**65truckowner** · 12-06-2021, 08:59 PM

Thanks. I have a patch panel ordered

12-05-2021, 07:23 PM	#1
65truckowner Senior Member Join Date: Oct 2012 Location: mountain view arkansas Posts: 1,316	patina question I am building a 1965 c10 patina. My drivers side fender is really rough Should I cut out the bad and patch then primer or just bolt it on. Here is a picture of the truck and the fender.IMG_4611 by Daniel Crymes, on Flickr IMG_4610 by Daniel Crymes, on Flickr __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=548705

12-05-2021, 07:33 PM	#2
Billy Stuck Registered User Join Date: Sep 2020 Location: Grand Rapids, MI Posts: 3	Re: patina question I'd be tempted to fix the rust, go a bit smoother on the wrinkles, and then fauxtina it back.

12-05-2021, 08:14 PM	#3
jocko Senior Member Join Date: Oct 2009 Location: Godley, TX Posts: 17,975	Re: patina question that's a bit beyond patina, I'm with Billy.

12-05-2021, 09:13 PM	#4
65truckowner Senior Member Join Date: Oct 2012 Location: mountain view arkansas Posts: 1,316	Re: patina question That is what I was thinking as well __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=548705

12-05-2021, 10:33 PM	#5
cwcarpenter98 Senior Member Join Date: Jan 2018 Location: Hickory Flat, GA Posts: 4,488	Re: patina question I'll third Billy. Since you already have to fauxtina the rockers, the fender would look better that way too __________________ Christian Carpenter 1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive Overdrive wiring here 1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson

12-06-2021, 08:59 PM	#6
65truckowner Senior Member Join Date: Oct 2012 Location: mountain view arkansas Posts: 1,316	Re: patina question Thanks. I have a patch panel ordered __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=548705

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.