My 85 chevy c10 build - Page 10 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

CuRtdOgG · 04-27-2012, 07:24 AM

Plan on doing a little work today...iv been working longer hours and havent really had extra time lately...I am needing to drive this truck Soo bad!!
Posted via Mobile Device

CuRtdOgG · 04-28-2012, 05:03 PM

So I did a little..I took my air tank sanded it and cleaned it up and painted it black. I also discovered I need all new cab mounts and bolts along with bed bolts...I also need to get the trans crossmember...moose..where did u order yours from? I need to get fuel pump filter, fuel lines and trans lines. I'm also working on the bed...I took some pics.

IMAG0442 by catkinson896, on Flickr

IMAG0434 by catkinson896, on Flickr

IMAG0439 by catkinson896, on Flickr
Posted via Mobile Device

CuRtdOgG · 04-28-2012, 05:06 PM

IMAG0443 by catkinson896, on Flickr

IMAG0446 by catkinson896, on Flickr
Posted via Mobile Device

legendman · 04-28-2012, 08:40 PM

Nice, making some good progress.

CuRtdOgG · 08-05-2012, 01:25 AM

IMAG0580 by catkinson896, on Flickr

IMAG0582 by catkinson896, on Flickr

IMAG0584 by catkinson896, on Flickr

Got this thing in my garage now. I can start re-wiring the switches. Mount the airtank on the frame on the pass side and install the compressors on the rear. Then re-do the hoses and wire it up so the suspension is ready to go. Then onto the motor. Then body work and then will be time for a cruise!
Posted via Mobile Device

CuRtdOgG · 08-05-2012, 04:18 AM

Just finished mounting the first compressor. Got it all wired minus the pressure switch wire. Gotta wait till I mount the tank and move some airlines for that. Went pretty well. I'm happy with it and this way everything will be hidden under the bed mounted on the frame!

IMAG0587 by catkinson896, on Flickr

IMAG0585 by catkinson896, on Flickr
Posted via Mobile Device

CuRtdOgG · 08-06-2012, 04:55 AM

Just finished getting both compressors mounted. Got them all wired up except for the two wires that go to the pressure switch , which ill do once I mount the tank. And I mounted the air filters on the inside of the frame rail.

IMAG0588 by catkinson896, on Flickr

IMAG0589 by catkinson896, on Flickr

IMAG0590 by catkinson896, on Flickr
Posted via Mobile Device

maxxxy · 08-06-2012, 10:31 AM

Looks good! Will your tank fit in between the rear frame rails? If it did, I'd think that'd look better and be easier to later access all the compressors, tank, and valves, if they were in the same place, rather than on the passenger side. I mean mine is on the passenger side, so there's nothing wrong with it being there. Lol.
Posted via Mobile Device

CuRtdOgG · 08-06-2012, 02:47 PM

It is too wide. Or I would. I'll look maybe I could figure out a diff spot i dono yet.
Posted via Mobile Device

okndnx · 08-06-2012, 02:51 PM

You should think about mounting your compressors with the heads upright

CuRtdOgG · 08-06-2012, 04:14 PM

Do they not work on their side?
Posted via Mobile Device

maxxxy · 08-09-2012, 01:14 AM

This is straight from the viair website.

Q: Is it possible to mount VIAIR compressors sideways, or must it be mounted with the cylinder upright?
A: You can mount in any direction or position since VIAIR compressors are oil-less. The only position we do not recommend is an upside-down mount, since heat tends to travel upward, and does not dissipate well in the motor housing. A sideways mounting may reduce the life of the piston seal, since everything is governed by gravity and has a weight associated with it.
Posted via Mobile Device

CuRtdOgG · 08-10-2012, 10:22 PM

Thanks max. I think ill leave them there. They fit nicely and will be hidden!
Posted via Mobile Device

king-918 · 08-16-2012, 08:37 PM

glad to see others here around the city doing this too!

CuRtdOgG · 08-17-2012, 05:00 PM

Your doing the same! Nice. I'll check your thread out
Posted via Mobile Device

luifer76 · 08-20-2012, 10:47 PM

looking good curt are you gonna paint the frame while you have it all apart?

CuRtdOgG · 08-22-2012, 03:10 AM

I wish I would...but how much work would that be...im jist lazy man. I dread taking all the lines off and the work....but I should get over it and do it...it would be way better huh...how long do u think that would take?
Posted via Mobile Device

WarBeard · 08-22-2012, 03:12 AM

Lazy is painting the frame with the lines on it

luifer76 · 08-24-2012, 12:05 AM

Quote:

Originally Posted by CuRtdOgG

I wish I would...but how much work would that be...im jist lazy man. I dread taking all the lines off and the work....but I should get over it and do it...it would be way better huh...how long do u think that would take?
Posted via Mobile Device

if i was you and i had the frame by itself just laying there i would yank all the lold wires out of there and take all the air ride stuff off and paint everything and even if it took you a little longer than what you want, you will feel better about it and you gonna be glad you did it while it was all apart beacuse i can almost guarantee that you gonna wish you did it but than its gonna be too late cause you gonna have the truck all put back together... been there done that.... i always rush and than wish i would have done it different later.

CuRtdOgG · 08-27-2012, 05:37 AM

I'm gonna do...i guess all I got is time. It will be awesome in the long run. Thanks guys
Posted via Mobile Device

king-918 · 08-28-2012, 12:56 PM

Where are you at? Anymore pictures?
Posted via Mobile Device

luifer76 · 08-28-2012, 04:19 PM

Quote:

Originally Posted by CuRtdOgG

I'm gonna do...i guess all I got is time. It will be awesome in the long run. Thanks guys
Posted via Mobile Device

sweet post pics lol....

CuRtdOgG · 08-29-2012, 11:43 AM

Well i got the airlines and switch solenoids off. Not much but some progress...i just need to take the fuel lines and tank off then the front end and brake lines then start prepping for paint. not much but heres a few pics.

IMAG0614 by catkinson896, on Flickr

IMAG0613 by catkinson896, on Flickr

IMAG0615 by catkinson896, on Flickr
Posted via Mobile Device

luifer76 · 08-29-2012, 09:27 PM

moving forward bro ..... looks good.

CuRtdOgG · 10-13-2012, 03:26 AM

really need to quit being lazy and do some work....

04-27-2012, 07:24 AM	#226
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build Plan on doing a little work today...iv been working longer hours and havent really had extra time lately...I am needing to drive this truck Soo bad!! Posted via Mobile Device

04-28-2012, 05:03 PM	#227
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build So I did a little..I took my air tank sanded it and cleaned it up and painted it black. I also discovered I need all new cab mounts and bolts along with bed bolts...I also need to get the trans crossmember...moose..where did u order yours from? I need to get fuel pump filter, fuel lines and trans lines. I'm also working on the bed...I took some pics. IMAG0442 by catkinson896, on Flickr IMAG0442 by catkinson896, on Flickr IMAG0442 by catkinson896, on Flickr IMAG0434 by catkinson896, on Flickr IMAG0439 by catkinson896, on Flickr Posted via Mobile Device

04-28-2012, 05:06 PM	#228
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build IMAG0443 by catkinson896, on Flickr IMAG0446 by catkinson896, on Flickr Posted via Mobile Device

08-05-2012, 01:25 AM	#230
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build IMAG0580 by catkinson896, on Flickr IMAG0582 by catkinson896, on Flickr IMAG0584 by catkinson896, on Flickr Got this thing in my garage now. I can start re-wiring the switches. Mount the airtank on the frame on the pass side and install the compressors on the rear. Then re-do the hoses and wire it up so the suspension is ready to go. Then onto the motor. Then body work and then will be time for a cruise! Posted via Mobile Device

08-05-2012, 04:18 AM	#231
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build Just finished mounting the first compressor. Got it all wired minus the pressure switch wire. Gotta wait till I mount the tank and move some airlines for that. Went pretty well. I'm happy with it and this way everything will be hidden under the bed mounted on the frame! IMAG0587 by catkinson896, on Flickr IMAG0585 by catkinson896, on Flickr Posted via Mobile Device

08-06-2012, 04:55 AM	#232
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build Just finished getting both compressors mounted. Got them all wired up except for the two wires that go to the pressure switch , which ill do once I mount the tank. And I mounted the air filters on the inside of the frame rail. IMAG0588 by catkinson896, on Flickr IMAG0589 by catkinson896, on Flickr IMAG0590 by catkinson896, on Flickr Posted via Mobile Device

08-06-2012, 10:31 AM	#233
maxxxy Registered User Join Date: Jul 2010 Location: Norman, Oklahoma Posts: 557	Re: My 85 chevy c10 build Looks good! Will your tank fit in between the rear frame rails? If it did, I'd think that'd look better and be easier to later access all the compressors, tank, and valves, if they were in the same place, rather than on the passenger side. I mean mine is on the passenger side, so there's nothing wrong with it being there. Lol. Posted via Mobile Device __________________ Max Max's bagged 81 81 rcsb bagged, 22s, build in progress 09 ext cab, 24" U2's, DD sub/amp

08-06-2012, 02:47 PM	#234
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build It is too wide. Or I would. I'll look maybe I could figure out a diff spot i dono yet. Posted via Mobile Device

08-06-2012, 02:51 PM	#235
okndnx Registered User Join Date: Oct 2009 Location: Skiatook Oklahoma Posts: 33	Re: My 85 chevy c10 build You should think about mounting your compressors with the heads upright

08-06-2012, 04:14 PM	#236
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build Do they not work on their side? Posted via Mobile Device

08-09-2012, 01:14 AM	#237
maxxxy Registered User Join Date: Jul 2010 Location: Norman, Oklahoma Posts: 557	Re: My 85 chevy c10 build This is straight from the viair website. Q: Is it possible to mount VIAIR compressors sideways, or must it be mounted with the cylinder upright? A: You can mount in any direction or position since VIAIR compressors are oil-less. The only position we do not recommend is an upside-down mount, since heat tends to travel upward, and does not dissipate well in the motor housing. A sideways mounting may reduce the life of the piston seal, since everything is governed by gravity and has a weight associated with it. Posted via Mobile Device __________________ Max Max's bagged 81 81 rcsb bagged, 22s, build in progress 09 ext cab, 24" U2's, DD sub/amp

08-10-2012, 10:22 PM	#238
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build Thanks max. I think ill leave them there. They fit nicely and will be hidden! Posted via Mobile Device

08-16-2012, 08:37 PM	#239
king-918 Registered User Join Date: Nov 2011 Location: Oklahoma City Oklahoma Posts: 1,056	Re: My 85 chevy c10 build glad to see others here around the city doing this too! __________________ <----Christopher My Tardis Oh yeah I'm really a Toyota guy, but had some stuff sitting around. Oklahoma

08-17-2012, 05:00 PM	#240
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build Your doing the same! Nice. I'll check your thread out Posted via Mobile Device

08-20-2012, 10:47 PM	#241
luifer76 Registered User Join Date: Jul 2010 Location: Southern California CA Posts: 1,088	Re: My 85 chevy c10 build looking good curt are you gonna paint the frame while you have it all apart? __________________ nOtHiNg LiKe ThE gOoD oLe ChEvYs....



Register or Log In To remove these advertisements.

08-22-2012, 03:10 AM	#242
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build I wish I would...but how much work would that be...im jist lazy man. I dread taking all the lines off and the work....but I should get over it and do it...it would be way better huh...how long do u think that would take? Posted via Mobile Device

08-22-2012, 03:12 AM	#243
WarBeard Registered User Join Date: Jul 2008 Location: Show low,az Posts: 808	Re: My 85 chevy c10 build Lazy is painting the frame with the lines on it __________________ 1978 C10 Silverado Big 10 350/350.. play toy 1990 V1500 Suburban 350/700r4..Daily driver 1987 K10 Silverado 383/400.. Wife's rig WRECKED! 1989 V2500 Suburban 350/400.. SOLD! 1974 C10 Custom10 LWB 350/350.. SOLD! 1974 C10 Custom10 SWB 350/400.. SOLD! 1999 Silverado Z71 LS1.. Wife's rig WRECKED! On the hunt for a new project....... I'm a Chevy guy.....I'm just not a "NEW" Chevy guy.

08-27-2012, 05:37 AM	#245
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build I'm gonna do...i guess all I got is time. It will be awesome in the long run. Thanks guys Posted via Mobile Device

08-28-2012, 12:56 PM	#246
king-918 Registered User Join Date: Nov 2011 Location: Oklahoma City Oklahoma Posts: 1,056	Re: My 85 chevy c10 build Where are you at? Anymore pictures? Posted via Mobile Device __________________ <----Christopher My Tardis Oh yeah I'm really a Toyota guy, but had some stuff sitting around. Oklahoma

08-29-2012, 11:43 AM	#248
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build Well i got the airlines and switch solenoids off. Not much but some progress...i just need to take the fuel lines and tank off then the front end and brake lines then start prepping for paint. not much but heres a few pics. IMAG0614 by catkinson896, on Flickr IMAG0613 by catkinson896, on Flickr IMAG0615 by catkinson896, on Flickr Posted via Mobile Device

08-29-2012, 09:27 PM	#249
luifer76 Registered User Join Date: Jul 2010 Location: Southern California CA Posts: 1,088	Re: My 85 chevy c10 build moving forward bro ..... looks good. __________________ nOtHiNg LiKe ThE gOoD oLe ChEvYs....

10-13-2012, 03:26 AM	#250
CuRtdOgG Registered User Join Date: Aug 2010 Location: norman, ok Posts: 305	Re: My 85 chevy c10 build really need to quit being lazy and do some work....

Register or Log In To remove these advertisements.