Project 67 DRGNWGN - 67 Burban!! - Page 16 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**kev2809** · 05-22-2011, 04:02 PM

and there goes the orange wire..lol. surprised the hole was about the size of a penny.

FRENCHBLUE72 · 05-22-2011, 04:20 PM

I have just the basics on the drivers side. The fuse panel was relocated to above the trans tunnel and ran to the frame that way..

67chevy1series · 05-22-2011, 05:13 PM

67s dont have many unnessacery holes.... nice work it should look alot better with a coat of primer

**kev2809** · 05-22-2011, 07:34 PM

so what are all those little screws coming out of the driver side?

texastrendz · 05-22-2011, 09:57 PM

well, i own a bunch of welders. lol. i used a hobart 230 machine for those i believe. i also own a Lincoln 220 and 110 machine. i would use a 220 machine just for the amperage you will need to penetrate. i know some people say they can get a 110 machine hot enough, i could never get it to do it. a welder is a good investment, and over time it may actually make you money by doing jobs for other people.

**kev2809** · 05-22-2011, 10:07 PM

ya your right. i been wanting to buy a 220 for a while, but its hard to invest in expensive tools because it takes away from my truck for a long time lol.

i thought about turning it into money from other jobs too, but i have a horrible consious (sp?) thats why i dont even want to weld on my own frame...i guess experience would take care of that though..

67chevy1series · 05-22-2011, 11:49 PM

Quote:

Originally Posted by kev2809

so what are all those little screws coming out of the driver side?

they are for a "jute padding" to sound deadned the cab

**kev2809** · 05-23-2011, 09:42 AM

so they can just be cut right off on the firewall?

**kev2809** · 05-23-2011, 11:10 PM

im thinking also to maybe buy these [IMG]http://*******************/files/imagecache/product/Over_Axle_Lower.jpg[/IMG]from suicide doors and weld 2 pieces of square tubing across the notch and weld a square 3/16" plate across, and mount the top bag to it. the lower bracket is only 30 bucks, and im sure i can rummage around for the tubing and top plate. those kp brackets are nice but they are over 100 bucks shipped!

charx2 · 05-23-2011, 11:42 PM

I thought about those too but decided to go with the under axle ones. Im going to order some sleeve bags tomorrow I think and do Some fab work to get it all to work right.
Posted via Mobile Device

67chevy1series · 05-23-2011, 11:51 PM

Quote:

Originally Posted by kev2809

so they can just be cut right off on the firewall?

yes no need for those holes unless you want the padding

**kev2809** · 05-24-2011, 06:07 AM

Quote:

Originally Posted by charx2

I thought about those too but decided to go with the under axle ones. Im going to order some sleeve bags tomorrow I think and do Some fab work to get it all to work right.
Posted via Mobile Device

is there a reason your going to use sleeve bags instead of regular bags? i think you can still use the kp brackets with sleeve bags either way though..

Quote:

Originally Posted by 67chevy1series

yes no need for those holes unless you want the padding

they just might be coming off then lol

**kev2809** · 05-24-2011, 09:02 PM

ordered the thorbecke bros axle brackets i posted above. should be here middle or end of next week, so maybe next weekend i can tear into it. im hoping this weekend i can borrow my friends cherry picker and maybe get this motor out of here finally!

67chevy1series · 05-24-2011, 09:35 PM

Quote:

Originally Posted by kev2809

they just might be coming off then lol

i figured that!

**kev2809** · 05-29-2011, 12:09 PM

well i still havent gotten the engine puller yet, so i decided to finish up the rear that i started on a few months ago. and heres how it turned out..

lot better than this...

still needs a little grinding and then filler but happy how it turned out. this was probably the hardest part i had to replace on this whole truck...lot of body curves and a tailgate hinge to make sure it was lined right, lot of relief cuts and splices. you can see its still a little bent in, but the bumper will cover that anyways

67chevy1series · 05-30-2011, 01:59 AM

nice job a skim coat of bondo and your done

maxxxy · 05-31-2011, 11:52 PM

I've seen you around on the forum, but I've never really looked too much into your build. I just read all 16 pages of your thread, and let me just say that you do some impressive work. Keep it up man.
Posted via Mobile Device

**kev2809** · 06-02-2011, 07:26 PM

Quote:

Originally Posted by 67chevy1series

nice job a skim coat of bondo and your done

haha...sure hope so. i actually cant wait to start the body work...im tired of welding and crap. i get burnt out quick of doing the same thing.

Quote:

Originally Posted by maxxxy

I've seen you around on the forum, but I've never really looked too much into your build. I just read all 16 pages of your thread, and let me just say that you do some impressive work. Keep it up man.
Posted via Mobile Device

thank you..appreciate you dropping in!

well guys, i got my axle brackets in a few days ago, had the day off so i went at it. cut them damn tubs out, that wasnt fun! im having a few problems trying to get everything lined up...some unusual problems. hope to get this all welded up by this weekend. heres a shot with the trailing arms up against the frame, with the bag mocked up. just a teaser til i get everything welded in, but should be what it will look like.

im really considering a spacer between the ta crossmember and ta's because im not really digging the offcentered wheel...

67chevy1series · 06-03-2011, 01:07 AM

burb looks nice, i wish i had a welder that worked ok

charx2 · 06-04-2011, 01:14 PM

Sweet! Looks like your making more progress than I am. I just have an idea and the material. No time though. But here is what I will most likely be doing. Something like this just cut to fit obviously and gussets where they need to be.

C20-67_N_MO · 06-05-2011, 09:49 PM

Very nice progress!

Hoping to start work on mine in the near future.

Congrats on a very cool project!!

**kev2809** · 06-06-2011, 09:41 AM

Quote:

Originally Posted by charx2

Sweet! Looks like your making more progress than I am. I just have an idea and the material. No time though. But here is what I will most likely be doing. Something like this just cut to fit obviously and gussets where they need to be.

that does look tough. could you make a square crossmember that hoops over the axle housing?

Quote:

Originally Posted by C20-67_N_MO

Very nice progress!

Hoping to start work on mine in the near future.

Congrats on a very cool project!!

thank you!

well, got everything wrapped up yesterday. it tough trying to weld with a 115 amp welder, i think before i attempt a "Z" im going to get a bigger welder! heres some progress pics from over the weekend..

was tough trying to get a good angle, but you get the idea! i still might add some 1" spacers between the bag...it doesnt get a lot of lift with this setup..it just clears over the top of the tire at full lift.

67chevy1series · 06-10-2011, 02:40 AM

burb looks good! keep it up bud!

1sik7t2 · 06-14-2011, 06:02 PM

berry nice...about the centered rear wheels,,drove me crazy with mine too we moved mine back and did a triangulated 4 link looks perfect now...mine WAS on the trailing arms too....keep "down" the good work!!!

Quote:

Originally Posted by kev2809

that does look tough. could you make a square crossmember that hoops over the axle housing?

thank you!

well, got everything wrapped up yesterday. it tough trying to weld with a 115 amp welder, i think before i attempt a "Z" im going to get a bigger welder! heres some progress pics from over the weekend..

was tough trying to get a good angle, but you get the idea! i still might add some 1" spacers between the bag...it doesnt get a lot of lift with this setup..it just clears over the top of the tire at full lift.

**kev2809** · 06-14-2011, 07:13 PM

lol..ya its hideous!

im thinking of putting these mirrors on...i picked them up from a friend from work. he was going to put them on his 87 el camino, but he just went with no mirrors.

what you guys think?

05-22-2011, 04:02 PM	#376
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: Project 67 DRGNWGN - 67 Burban!! and there goes the orange wire..lol. surprised the hole was about the size of a penny. __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

05-22-2011, 04:20 PM	#377
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: Project 67 DRGNWGN - 67 Burban!! I have just the basics on the drivers side. The fuse panel was relocated to above the trans tunnel and ran to the frame that way.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

05-22-2011, 05:13 PM	#378
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: Project 67 DRGNWGN - 67 Burban!! 67s dont have many unnessacery holes.... nice work it should look alot better with a coat of primer

05-22-2011, 07:34 PM	#379
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: Project 67 DRGNWGN - 67 Burban!! so what are all those little screws coming out of the driver side? __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

05-22-2011, 09:57 PM	#380
texastrendz Registered User Join Date: Jan 2008 Location: HOUSTON TX Posts: 1,161	Re: Project 67 DRGNWGN - 67 Burban!! well, i own a bunch of welders. lol. i used a hobart 230 machine for those i believe. i also own a Lincoln 220 and 110 machine. i would use a 220 machine just for the amperage you will need to penetrate. i know some people say they can get a 110 machine hot enough, i could never get it to do it. a welder is a good investment, and over time it may actually make you money by doing jobs for other people.

05-22-2011, 10:07 PM	#381
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: Project 67 DRGNWGN - 67 Burban!! ya your right. i been wanting to buy a 220 for a while, but its hard to invest in expensive tools because it takes away from my truck for a long time lol. i thought about turning it into money from other jobs too, but i have a horrible consious (sp?) thats why i dont even want to weld on my own frame...i guess experience would take care of that though.. __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

05-23-2011, 09:42 AM	#383
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: Project 67 DRGNWGN - 67 Burban!! so they can just be cut right off on the firewall? __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

05-23-2011, 11:10 PM	#384
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: Project 67 DRGNWGN - 67 Burban!! im thinking also to maybe buy these [IMG]http://*****************/files/imagecache/product/Over_Axle_Lower.jpg[/IMG]from suicide doors and weld 2 pieces of square tubing across the notch and weld a square 3/16" plate across, and mount the top bag to it. the lower bracket is only 30 bucks, and im sure i can rummage around for the tubing and top plate. those kp brackets are nice but they are over 100 bucks shipped! __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread** -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_] Last edited by kev2809; 05-23-2011 at 11:10 PM.

05-23-2011, 11:42 PM	#385
charx2 Registered User Join Date: Apr 2010 Location: Mobile, AL Posts: 365	Re: Project 67 DRGNWGN - 67 Burban!! I thought about those too but decided to go with the under axle ones. Im going to order some sleeve bags tomorrow I think and do Some fab work to get it all to work right. Posted via Mobile Device __________________ ----------------------------------------- My 67 c10 Thread. http://67-72chevytrucks.com/vboard/s...d.php?t=409192

05-24-2011, 09:02 PM	#388
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: Project 67 DRGNWGN - 67 Burban!! ordered the thorbecke bros axle brackets i posted above. should be here middle or end of next week, so maybe next weekend i can tear into it. im hoping this weekend i can borrow my friends cherry picker and maybe get this motor out of here finally! __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

05-29-2011, 12:09 PM	#390
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: Project 67 DRGNWGN - 67 Burban!! well i still havent gotten the engine puller yet, so i decided to finish up the rear that i started on a few months ago. and heres how it turned out.. lot better than this... still needs a little grinding and then filler but happy how it turned out. this was probably the hardest part i had to replace on this whole truck...lot of body curves and a tailgate hinge to make sure it was lined right, lot of relief cuts and splices. you can see its still a little bent in, but the bumper will cover that anyways __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_] Last edited by kev2809; 05-30-2011 at 09:38 AM.

05-30-2011, 01:59 AM	#391
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: Project 67 DRGNWGN - 67 Burban!! nice job a skim coat of bondo and your done

05-31-2011, 11:52 PM	#392
maxxxy Registered User Join Date: Jul 2010 Location: Norman, Oklahoma Posts: 557	Re: Project 67 DRGNWGN - 67 Burban!! I've seen you around on the forum, but I've never really looked too much into your build. I just read all 16 pages of your thread, and let me just say that you do some impressive work. Keep it up man. Posted via Mobile Device __________________ Max Max's bagged 81 81 rcsb bagged, 22s, build in progress 09 ext cab, 24" U2's, DD sub/amp

06-03-2011, 01:07 AM	#394
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: Project 67 DRGNWGN - 67 Burban!! burb looks nice, i wish i had a welder that worked ok Last edited by 67chevy1series; 06-03-2011 at 01:08 AM.

06-04-2011, 01:14 PM	#395
charx2 Registered User Join Date: Apr 2010 Location: Mobile, AL Posts: 365	Re: Project 67 DRGNWGN - 67 Burban!! Sweet! Looks like your making more progress than I am. I just have an idea and the material. No time though. But here is what I will most likely be doing. Something like this just cut to fit obviously and gussets where they need to be. __________________ ----------------------------------------- My 67 c10 Thread. http://67-72chevytrucks.com/vboard/s...d.php?t=409192



Register or Log In To remove these advertisements.

06-05-2011, 09:49 PM	#396
C20-67_N_MO Champagne Taste on Beer Budget Join Date: Dec 2008 Location: High Ridge, Missouri Posts: 2,190	Re: Project 67 DRGNWGN - 67 Burban!! Very nice progress! Hoping to start work on mine in the near future. Congrats on a very cool project!! __________________ Coming Soon: Project 1970 Country Truck

06-10-2011, 02:40 AM	#398
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: Project 67 DRGNWGN - 67 Burban!! burb looks good! keep it up bud!

06-14-2011, 07:13 PM	#400
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,175	Re: Project 67 DRGNWGN - 67 Burban!! lol..ya its hideous! im thinking of putting these mirrors on...i picked them up from a friend from work. he was going to put them on his 87 el camino, but he just went with no mirrors. what you guys think? __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

Register or Log In To remove these advertisements.