New project @ Street Machinery 1966 C10 - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jimmydean · 02-18-2011, 02:39 PM

Man, that looks great.

**way2lo2** · 02-18-2011, 06:38 PM

Quote:

Originally Posted by way2lo2

Pulled the cab and off to the strippers on Tuesday. You guys out west don't know how lucky you are.

I take back what I said about Cali......................oh I guess its not too bad but I'm alittle disappointed how thin the metal was. Seemed a lot more solid but the strippers blew right through some areas, not the end of the world but a week or two set back.

Dinos63 · 02-18-2011, 07:40 PM

MAN BORRIS OUT HERE WE SCRAP THAT CAB WAAAAY TO MUCH RUST

LOOKS GOOD KAT!! YOU COMIN OUT IN MARCH??

**Captainfab** · 02-19-2011, 01:23 AM

What I always say, is it is better to find it now than later. That's one of the things I like about media blasting everything. That floor rust was likely a result of a leaky windshield seal.

disturbinglykool · 02-19-2011, 05:43 PM

Boris; rust or not its lookin good baby...big window conversion and fender wells...you must be mad at somebody. I have first hand knowledge on the quality of your work with my 58 so I am on the edge of my seat to see what it will look like done. Any pimp renderings?

64shortc10 · 04-14-2011, 05:24 PM

Anything new with this bad boy?
Tony from Norcal

hotrodhomi · 04-14-2011, 06:05 PM

cool build

**ChiefRocka** · 04-15-2011, 05:38 AM

**way2lo2** · 04-19-2011, 07:10 PM

The unexpected rust repair has slowed me alittle bit.
New inner and outer rockers.

**way2lo2** · 04-19-2011, 07:15 PM

my donor inner big back window panel had some pin holes but its primed and ready for an application of lizard skin. The opening in the cab has been cut and ready for primer then lizard skin before the inner panel is installed.

**way2lo2** · 04-19-2011, 07:20 PM

started working on the suicidedoors chassis, it was basically a roller when I got it, I just had to plumb it, put brakes on it, and change to a power rack.

**way2lo2** · 04-19-2011, 07:24 PM

change of plans on wheels meant different wheel wells.....

c.brown · 04-19-2011, 08:13 PM

very nice start like the way the inner fenders are turning out you got me thinking

kart34 · 04-19-2011, 08:56 PM

Looking good ....

64shortc10 · 04-19-2011, 11:36 PM

Nice! What rear brake setup is that? And what does it cost? Thanks!
Tony from Norcal
Posted via Mobile Device

**way2lo2** · 04-20-2011, 07:46 AM

Quote:

Originally Posted by 64shortc10

Nice! What rear brake setup is that? And what does it cost? Thanks!
Tony from Norcal
Posted via Mobile Device

I bought brackets off this site from Captainfab, they use 93-97 Camaro rear calipers and 94-96 Impala SS rear rotors. I think I have less then $500 in everything.

creep · 04-20-2011, 07:48 AM

Can't wait to see this one.

Bkndsdl · 04-20-2011, 08:25 AM

Awesome build! May I ask what exactly is Lizard Skin?

**N2TRUX** · 04-20-2011, 08:45 AM

Those wheel tubs look awesome Boris. Keep the progress reports coming.

Bkndsdl-
LizardSkin Ceramic Insulation is a premium spray-on insulation for all cars and trucks, street rods and customs, race cars,experimental aircraft, and high end audio installations---wherever heat is a problem on your ride.

gostranger · 04-20-2011, 09:33 AM

awesome looking build!! nice work!!!

Fabian · 04-21-2011, 11:58 AM

Very nice work Boris!

Looks fantastic.

**way2lo2** · 04-21-2011, 12:56 PM

Quote:

Originally Posted by Bkndsdl

Awesome build! May I ask what exactly is Lizard Skin?

its spray on insulation, to help against heat and a sound proofing as well.

64shortc10 · 04-21-2011, 01:57 PM

Do you plan to weld the bbw panel back in or do it like Scoti and panel adhesive? Cool project! Did you sell the big wheels that came with the suicide doors chassis?
Tony from Norcal
Posted via Mobile Device

**way2lo2** · 04-21-2011, 02:11 PM

Quote:

Originally Posted by 64shortc10

Do you plan to weld the bbw panel back in or do it like Scoti and panel adhesive? Cool project! Did you sell the big wheels that came with the suicide doors chassis?
Tony from Norcal
Posted via Mobile Device

weld it around the window opening and along the sides under the door weatherstrip, bond it to the back of the cab at the bottom and the inner roof at the top. The only thing I don't like is that where the inner window panel and inner roof meet is there is no way to get clamps to pull them tight so I may end up welding the seam and body working the inside of the cab, kind of waiting to get the panel fully installed first. The 22" that came with the chassis are sold.

Dinos63 · 04-21-2011, 03:04 PM

Quote:

Originally Posted by way2lo2

change of plans on wheels meant different wheel wells.....

WOW!! LOOKS KILLER KAT!! AND AHH LETS SEE THEM WHEELS

02-18-2011, 02:39 PM	#51
jimmydean Registered User Join Date: May 2005 Location: Beaverton, OR Posts: 3,728	Re: New project @ Street Machinery 1966 C10 Man, that looks great. __________________ New Project: 1966 LWB C20 Plans: 1/2 ton conversion Dropmember front Dropmember rear Corvette discs Restored raised bed http://67-72chevytrucks.com/vboard/s....php?p=4295210

02-18-2011, 07:40 PM	#53
Dinos63 chevy only Join Date: Sep 2006 Location: Phoenix, AZ Posts: 6,619	Re: New project @ Street Machinery 1966 C10 MAN BORRIS OUT HERE WE SCRAP THAT CAB WAAAAY TO MUCH RUST LOOKS GOOD KAT!! YOU COMIN OUT IN MARCH?? __________________ CHEVY ONLY... Nothin Else !

02-19-2011, 01:23 AM	#54
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: New project @ Street Machinery 1966 C10 What I always say, is it is better to find it now than later. That's one of the things I like about media blasting everything. That floor rust was likely a result of a leaky windshield seal. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE Last edited by Captainfab; 02-19-2011 at 01:23 AM.

02-19-2011, 05:43 PM	#55
disturbinglykool Registered User Join Date: Nov 2010 Location: Phoenix Posts: 248	Re: New project @ Street Machinery 1966 C10 Boris; rust or not its lookin good baby...big window conversion and fender wells...you must be mad at somebody. I have first hand knowledge on the quality of your work with my 58 so I am on the edge of my seat to see what it will look like done. Any pimp renderings?

04-14-2011, 05:24 PM	#56
64shortc10 Registered User Join Date: Jan 2007 Location: Winters, Ca. Posts: 1,069	Re: New project @ Street Machinery 1966 C10 Anything new with this bad boy? Tony from Norcal

04-14-2011, 06:05 PM	#57
hotrodhomi Registered User Join Date: Apr 2004 Location: Sacramento Posts: 3,737	Re: New project @ Street Machinery 1966 C10 cool build __________________ '72 2wd blazer, bagged w/ watts link & EDC '72 C10 "Lowered Farm Truck" STOLEN 5-18-11 '66 impala ht

04-15-2011, 05:38 AM	#58
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: New project @ Street Machinery 1966 C10 __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

04-19-2011, 07:10 PM	#59
way2lo2 way2lo2 Join Date: Sep 2004 Location: Cleveland , Ohio Posts: 803	Re: New project @ Street Machinery 1966 C10 The unexpected rust repair has slowed me alittle bit. New inner and outer rockers. Attached Images __________________ Dealer for Billet Specialties, Ridetech, Airlift, Vintage Air and others. Feel free to call, email, or PM for a quote. 216 481-5219 office 216 481-4240 fax 216 789-1647 mobile Way2Lo2@aol.com <----also my paypal http://www.hubgarage.com/mygarage/way2Lo2

04-19-2011, 07:15 PM	#60
way2lo2 way2lo2 Join Date: Sep 2004 Location: Cleveland , Ohio Posts: 803	Re: New project @ Street Machinery 1966 C10 my donor inner big back window panel had some pin holes but its primed and ready for an application of lizard skin. The opening in the cab has been cut and ready for primer then lizard skin before the inner panel is installed. Attached Images __________________ Dealer for Billet Specialties, Ridetech, Airlift, Vintage Air and others. Feel free to call, email, or PM for a quote. 216 481-5219 office 216 481-4240 fax 216 789-1647 mobile Way2Lo2@aol.com <----also my paypal http://www.hubgarage.com/mygarage/way2Lo2

04-19-2011, 07:20 PM	#61
way2lo2 way2lo2 Join Date: Sep 2004 Location: Cleveland , Ohio Posts: 803	Re: New project @ Street Machinery 1966 C10 started working on the suicidedoors chassis, it was basically a roller when I got it, I just had to plumb it, put brakes on it, and change to a power rack. Attached Images __________________ Dealer for Billet Specialties, Ridetech, Airlift, Vintage Air and others. Feel free to call, email, or PM for a quote. 216 481-5219 office 216 481-4240 fax 216 789-1647 mobile Way2Lo2@aol.com <----also my paypal http://www.hubgarage.com/mygarage/way2Lo2

04-19-2011, 07:24 PM	#62
way2lo2 way2lo2 Join Date: Sep 2004 Location: Cleveland , Ohio Posts: 803	Re: New project @ Street Machinery 1966 C10 change of plans on wheels meant different wheel wells..... Attached Images __________________ Dealer for Billet Specialties, Ridetech, Airlift, Vintage Air and others. Feel free to call, email, or PM for a quote. 216 481-5219 office 216 481-4240 fax 216 789-1647 mobile Way2Lo2@aol.com <----also my paypal http://www.hubgarage.com/mygarage/way2Lo2

04-19-2011, 08:13 PM	#63
c.brown Registered User Join Date: Oct 2009 Location: harrison twp MI Posts: 292	Re: New project @ Street Machinery 1966 C10 very nice start like the way the inner fenders are turning out you got me thinking __________________ 1966 suburban slammed fuel injected 6.2L My build

04-19-2011, 08:56 PM	#64
kart34 Registered User Join Date: Jul 2009 Location: Blooming Prairie, Minnesota Posts: 673	Re: New project @ Street Machinery 1966 C10 Looking good .... __________________ edited by staff

04-19-2011, 11:36 PM	#65
64shortc10 Registered User Join Date: Jan 2007 Location: Winters, Ca. Posts: 1,069	Re: New project @ Street Machinery 1966 C10 Nice! What rear brake setup is that? And what does it cost? Thanks! Tony from Norcal Posted via Mobile Device

04-20-2011, 07:48 AM	#67
creep Registered Loser Join Date: Jun 2009 Location: Elyria, OH Posts: 1,523	Re: New project @ Street Machinery 1966 C10 Can't wait to see this one. __________________ ((..)) ((0)) '63 GMC lwb, 383, th350, lays frame, genuine patina. The Build Thread - http://67-72chevytrucks.com/vboard/s...d.php?t=374267 '88 Astro cargo bagged, shaved, phantom grille. SOLD '50 Chevy 2 door sedan awaiting attention. 2014 Silverado Ext cab, 5.3, daily driver.



Register or Log In To remove these advertisements.

04-20-2011, 08:25 AM	#68
Bkndsdl Registered User Join Date: Dec 2009 Location: Irvington, Alabama Posts: 175	Re: New project @ Street Machinery 1966 C10 Awesome build! May I ask what exactly is Lizard Skin? __________________ -Mike from Alabama Why do we park on a driveway, and drive on a parkway? Jake - '67 Short Step Dirty Dan - '80 Short Fleet

04-20-2011, 08:45 AM	#69
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: New project @ Street Machinery 1966 C10 Those wheel tubs look awesome Boris. Keep the progress reports coming. Bkndsdl- LizardSkin Ceramic Insulation is a premium spray-on insulation for all cars and trucks, street rods and customs, race cars,experimental aircraft, and high end audio installations---wherever heat is a problem on your ride. __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

04-20-2011, 09:33 AM	#70
gostranger 65 suburban vortec 5.3 bagged Join Date: Jun 2005 Location: upstate new york Posts: 1,317	Re: New project @ Street Machinery 1966 C10 awesome looking build!! nice work!!!

04-21-2011, 11:58 AM	#71
Fabian Registered User Join Date: Feb 2011 Location: Germany Posts: 381	Re: New project @ Street Machinery 1966 C10 Very nice work Boris! Looks fantastic.

04-21-2011, 01:57 PM	#73
64shortc10 Registered User Join Date: Jan 2007 Location: Winters, Ca. Posts: 1,069	Re: New project @ Street Machinery 1966 C10 Do you plan to weld the bbw panel back in or do it like Scoti and panel adhesive? Cool project! Did you sell the big wheels that came with the suicide doors chassis? Tony from Norcal Posted via Mobile Device

Register or Log In To remove these advertisements.