TEXAS 81 swb build 5.3 4l80 - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

81chevys · 02-21-2014, 11:35 PM

Running into some probs though.... I got no power under 3000rpm. It barely moves itself until then but over 3k it blows the tires away. I did restall the converter to 2800-3200. It seams the engine is the one with the problem though. Also posted on ls1tech. I tried swapping o2 sensor plugs from side to side. No luck. Anybody got any ideas?

mattcrp1 · 02-24-2014, 11:18 AM

Did you find that with the Dirty Dingo mounts and the factory a/c position that the drag link came way to close to the oil pan and harness? I ended up removing the a/c and moving the whole eng/trans back to gain clearance on my LS install. Did you have to do the same?

81chevys · 02-25-2014, 03:42 AM

I pulled the dirty dingos and swapped for moroso because of the schnoenfeld headers. Too close to drglink as you stated. Moroso worked better for me

mattcrp1 · 02-25-2014, 10:23 AM

Thanks, did you relocate/remove the a/c and did you have to relocate the starter wiring? Got any pics of the Moroso set up? Good looking build so far.

81chevys · 02-25-2014, 11:46 AM

Ill try for in the morning to load some.

02-21-2014, 11:35 PM	#51
81chevys Registered User Join Date: Jun 2011 Location: houston,texas Posts: 58	Re: TEXAS 81 swb build 5.3 4l80 Running into some probs though.... I got no power under 3000rpm. It barely moves itself until then but over 3k it blows the tires away. I did restall the converter to 2800-3200. It seams the engine is the one with the problem though. Also posted on ls1tech. I tried swapping o2 sensor plugs from side to side. No luck. Anybody got any ideas?

02-24-2014, 11:18 AM	#52
mattcrp1 Registered User Join Date: May 2010 Location: Mountain House, CA Posts: 555	Re: TEXAS 81 swb build 5.3 4l80 Did you find that with the Dirty Dingo mounts and the factory a/c position that the drag link came way to close to the oil pan and harness? I ended up removing the a/c and moving the whole eng/trans back to gain clearance on my LS install. Did you have to do the same? __________________ My Chevy habit is paid for by Ford diesels... Here is my SLOW LS install: http://67-72chevytrucks.com/vboard/s...55#post6456355 Caliper Rebuild: http://67-72chevytrucks.com/vboard/s...d.php?t=613748 Upper Control Arm Bushings: http://67-72chevytrucks.com/vboard/s...d.php?t=616974 IG mattcrp1

02-25-2014, 03:42 AM	#53
81chevys Registered User Join Date: Jun 2011 Location: houston,texas Posts: 58	Re: TEXAS 81 swb build 5.3 4l80 I pulled the dirty dingos and swapped for moroso because of the schnoenfeld headers. Too close to drglink as you stated. Moroso worked better for me

02-25-2014, 10:23 AM	#54
mattcrp1 Registered User Join Date: May 2010 Location: Mountain House, CA Posts: 555	Re: TEXAS 81 swb build 5.3 4l80 Thanks, did you relocate/remove the a/c and did you have to relocate the starter wiring? Got any pics of the Moroso set up? Good looking build so far. __________________ My Chevy habit is paid for by Ford diesels... Here is my SLOW LS install: http://67-72chevytrucks.com/vboard/s...55#post6456355 Caliper Rebuild: http://67-72chevytrucks.com/vboard/s...d.php?t=613748 Upper Control Arm Bushings: http://67-72chevytrucks.com/vboard/s...d.php?t=616974 IG mattcrp1

02-25-2014, 11:46 AM	#55
81chevys Registered User Join Date: Jun 2011 Location: houston,texas Posts: 58	Re: TEXAS 81 swb build 5.3 4l80 Ill try for in the morning to load some.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.