'04 5.3L in a '01 V6 Camaro. - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

cableguy0 · 04-20-2015, 09:51 PM

Sometimes its cheaper to spend more money. Starting fresh is the better choice. Chasing an electrical gremlin will cause you to lose your mind later on. Considering it would probably take 10 hours or so to redo a harness yourself if not longer. Wiring is time consuming especially when terminating harness connectors.

Good luck with that rear....

clinebarger · 04-20-2015, 11:19 PM

Quote:

Originally Posted by cableguy0

Sometimes its cheaper to spend more money. Starting fresh is the better choice. Chasing an electrical gremlin will cause you to lose your mind later on. Considering it would probably take 10 hours or so to redo a harness yourself if not longer. Wiring is time consuming especially when terminating harness connectors.

Good luck with that rear....

Probably longer with a truck harness, The PCM is on the opposite end from a F-body. Your right....It would have been a nightmare!

I'm going to weld the axle tubes, Trick Flow diff cover, New Moser axles, Gears, Bearings & a used "Cone" Posi.
Being behind a automatic will help with longevity, T56 cars seem to tear them up more frequently. I'm not going to run drag radials or drag race it. It should be OK.

However, I'm not wearing rose colored glasses. When I put a 6.0L or 6.2L in it later on I will buy a 8.8" Ford housing for the car.

clinebarger · 05-03-2015, 10:03 PM

Scored an SLP filter lid, It fits the V6 base. The V6 lid is offset and will not work on a V8.

clinebarger · 05-03-2015, 10:09 PM

Trick Flow diff cover.

**oldman3** · 05-03-2015, 11:43 PM

Sweet looking cover...Jim

clinebarger · 05-28-2015, 11:22 PM

Got my engine harness from BP Automotive today. Man.....I'm IMPRESSED!!!!
The attention to detail is phenomenal, Bill got everything exactly right down to the Vacuum Line for the HVAC controls, To the Harness Bracket on the Evaporator Box.

Has the TAC module to Pedal harness integrated into the Engine Harness ($50 extra) But well worth it once I saw it done.

I will take some pics with my Camera later, Here is some fuzzy Cell Phone pics for now.

jessemthompson · 05-29-2015, 02:06 PM

Looks great. Mine should be shipping from BP today, I can't wait to get it.

clinebarger · 05-31-2015, 08:21 PM

Got the car to the shop yesterday, 6 miles with no coolant at all, Engine died a block away....Coasted up to the bay door

Only ran 3 stop signs & a right on red without stopping.

Started with rebuilding the Diff, I found the noise it was making...Driver side Carrier bearing was shot. I originally thought it was a Axle bearing.

Everything set right up with the original shims. .030" pinion shim & original 1-piece carrier shims.

Replace the rear rotors & pads, AC-Delco Rotors & GM (PBR) pads.

clinebarger · 05-31-2015, 08:31 PM

The Diff build went so smooth, I decided to go ahead & pull the engine/trans today. These cars are unbelievably easy to pull engines on. Took 1.5 hours. I'm sure it is a nightmare without a lift though.

clinebarger · 06-05-2015, 07:26 PM

Getting really close, Engine/Trans is in, wired, Exhaust done, Fuel system done. New brakes all the way around, Shocks & Struts, Power steering hoses, A/C hose assembly, Radiator hoses, Modified the Battery cables.

Need...
Alignment
Tires mounted & balanced
Wire Cruise control
Waiting for PCM from BP

clinebarger · 06-05-2015, 07:33 PM

More.

clinebarger · 06-05-2015, 07:40 PM

A/C hose assembly.

**Clyde65** · 06-05-2015, 08:46 PM

wow! fantastic job as usual Chris! Can I come look at her week after next??

clinebarger · 06-06-2015, 06:58 PM

Quote:

Originally Posted by Clyde65

wow! fantastic job as usual Chris! Can I come look at her week after next??

Your welcome any time John.

cableguy0 · 06-06-2015, 07:03 PM

I wanna come over and play..

Looking for any help. Just need relocation help and a place to live.

... Looks good. That car should be lots fun.

BR3W CITY · 06-07-2015, 01:26 AM

Quote:

Originally Posted by cableguy0

I wanna come over and play..

Looking for any help. Just need relocation help and a place to live.

I second that, and I'll expand it to any member whose build doesn't suck, and who has a comfy couch or a guest room. I work for myself, which I can do from anyones garage.

PS I need the WIFI password too.

**Clyde65** · 06-07-2015, 06:31 PM

Quote:

Originally Posted by clinebarger

Your welcome any time John.

Thank You Chris, I'll let you know before I do though!

clinebarger · 06-07-2015, 08:32 PM

Quote:

Originally Posted by cableguy0

I wanna come over and play..

Looking for any help. Just need relocation help and a place to live.

... Looks good. That car should be lots fun.

Quote:

Originally Posted by BR3W CITY

I second that, and I'll expand it to any member whose build doesn't suck, and who has a comfy couch or a guest room. I work for myself, which I can do from anyones garage.

PS I need the WIFI password too.

Come on down guys, Ya'll will have to fight over who gets the pool table & which one gets the floor.....Dinner is at Noon, Supper is at 7:00

jessemthompson · 06-09-2015, 10:09 PM

Quote:

Originally Posted by BR3W CITY

I second that, and I'll expand it to any member whose build doesn't suck, and who has a comfy couch or a guest room. I work for myself, which I can do from anyones garage.

PS I need the WIFI password too.

Br3w I have a guest room, a comfy couch, wifi password and a garage for you. Your advise here has been invaluable!

The camaro is coming along beautifully clinebarger! Can't wait to hear you have it running. Hopefully I'll have some updates to my build this weekend. My harness is due in tomorrow. I have my fingers crossed that the weather will cooperate with me along with my 2 yr old son.

clinebarger · 06-10-2015, 07:45 PM

Quote:

Originally Posted by jessemthompson

The camaro is coming along beautifully clinebarger! Can't wait to hear you have it running. Hopefully I'll have some updates to my build this weekend. My harness is due in tomorrow. I have my fingers crossed that the weather will cooperate with me along with my 2 yr old son.

Thanks man! Good luck on your build!

Started the engine up yesterday, Drove it to the Alignment shop today. Engine runs really good, Sounds great, I'm really excited!!

Only a short list of things so far....

Gas Gauge reads backwards.
A/C Clutch fuse blows when relay is commanded on.
Needs the MAF rescaled in the tune.
Exhaust hitting somewhere.

Going to get it home, Then send the PCM back to Bill @ BP.

jessemthompson · 06-11-2015, 06:32 AM

Congrats clinebarger, you'll get the little things worked out over time. There always seems to be a few things that need sorting out.

Low Elco · 08-29-2015, 12:26 AM

How did this work out? Rubber flying in the streets of Texas?

clinebarger · 08-29-2015, 10:19 PM

Quote:

Originally Posted by Low Elco

How did this work out? Rubber flying in the streets of Texas?

Not yet, I drove it to the house right after the front end alignment, Drove/Ran very well! I didn't get on it because the Trans & Gears are still breaking in, Parked it in the garage.....Been there ever since.

It has been TOO HOT for me to mess with it, 100 degrees & 50% humidity doesn't work well in my non-insulated metal garage, Soon as it cools down I will get back on it!

whitels1 · 09-05-2015, 01:43 AM

Nice work!

clinebarger · 09-14-2015, 08:06 PM

Finally got it finished up Saturday, Put a couple hundred miles on it so far, Very happy with it, Lights the tires at will

with the old ****y touring tires, The high performance tires I have should calm that down.

To do list....
Gas gauge still reads backwards....Not sure if I will/can fix that?
Need to swap out the Compressor Clutch, I have a good used one.
Re-torque header bolts.
Buy a key fob, Open the door, The alarm goes off 'til you turn the key on.
Mount & Balance tires.

Car in the driveway doing final fluid checks.

04-20-2015, 09:51 PM	#51
cableguy0 Senior Member Join Date: Apr 2000 Location: Delta,Pa Posts: 14,948	Re: '04 5.3L in a '01 V6 Camaro. Sometimes its cheaper to spend more money. Starting fresh is the better choice. Chasing an electrical gremlin will cause you to lose your mind later on. Considering it would probably take 10 hours or so to redo a harness yourself if not longer. Wiring is time consuming especially when terminating harness connectors. Good luck with that rear.... __________________ Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member.

05-03-2015, 10:03 PM	#53
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: '04 5.3L in a '01 V6 Camaro. Scored an SLP filter lid, It fits the V6 base. The V6 lid is offset and will not work on a V8. Attached Images

05-03-2015, 10:09 PM	#54
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: '04 5.3L in a '01 V6 Camaro. Trick Flow diff cover. Attached Images

05-03-2015, 11:43 PM	#55
oldman3 Senior Member Join Date: Mar 2011 Location: West Plains, Missouri Posts: 7,559	Re: '04 5.3L in a '01 V6 Camaro. Sweet looking cover...Jim __________________ my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br />

05-28-2015, 11:22 PM	#56
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: '04 5.3L in a '01 V6 Camaro. Got my engine harness from BP Automotive today. Man.....I'm IMPRESSED!!!! The attention to detail is phenomenal, Bill got everything exactly right down to the Vacuum Line for the HVAC controls, To the Harness Bracket on the Evaporator Box. Has the TAC module to Pedal harness integrated into the Engine Harness ($50 extra) But well worth it once I saw it done. I will take some pics with my Camera later, Here is some fuzzy Cell Phone pics for now. Attached Images

05-29-2015, 02:06 PM	#57
jessemthompson Registered User Join Date: Nov 2011 Location: Williamsburg, VA Posts: 960	Re: '04 5.3L in a '01 V6 Camaro. Looks great. Mine should be shipping from BP today, I can't wait to get it.

05-31-2015, 08:21 PM	#58
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: '04 5.3L in a '01 V6 Camaro. Got the car to the shop yesterday, 6 miles with no coolant at all, Engine died a block away....Coasted up to the bay door Only ran 3 stop signs & a right on red without stopping. Started with rebuilding the Diff, I found the noise it was making...Driver side Carrier bearing was shot. I originally thought it was a Axle bearing. Everything set right up with the original shims. .030" pinion shim & original 1-piece carrier shims. Replace the rear rotors & pads, AC-Delco Rotors & GM (PBR) pads. Attached Images Last edited by clinebarger; 05-31-2015 at 08:45 PM.

05-31-2015, 08:31 PM	#59
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: '04 5.3L in a '01 V6 Camaro. The Diff build went so smooth, I decided to go ahead & pull the engine/trans today. These cars are unbelievably easy to pull engines on. Took 1.5 hours. I'm sure it is a nightmare without a lift though. Attached Images

06-05-2015, 07:26 PM	#60
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: '04 5.3L in a '01 V6 Camaro. Getting really close, Engine/Trans is in, wired, Exhaust done, Fuel system done. New brakes all the way around, Shocks & Struts, Power steering hoses, A/C hose assembly, Radiator hoses, Modified the Battery cables. Need... Alignment Tires mounted & balanced Wire Cruise control Waiting for PCM from BP Attached Images

06-05-2015, 07:33 PM	#61
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: '04 5.3L in a '01 V6 Camaro. More. Attached Images

06-05-2015, 07:40 PM	#62
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: '04 5.3L in a '01 V6 Camaro. A/C hose assembly. Attached Images

06-05-2015, 08:46 PM	#63
Clyde65 1965 Chevy C10, 2005 4.8L/4l60 Join Date: Aug 2004 Location: DFW Texas Posts: 8,546	Re: '04 5.3L in a '01 V6 Camaro. wow! fantastic job as usual Chris! Can I come look at her week after next?? __________________ Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 *support our troops!*

06-06-2015, 07:03 PM	#65
cableguy0 Senior Member Join Date: Apr 2000 Location: Delta,Pa Posts: 14,948	Re: '04 5.3L in a '01 V6 Camaro. I wanna come over and play.. Looking for any help. Just need relocation help and a place to live. ... Looks good. That car should be lots fun. __________________ Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member.

06-11-2015, 06:32 AM	#71
jessemthompson Registered User Join Date: Nov 2011 Location: Williamsburg, VA Posts: 960	Re: '04 5.3L in a '01 V6 Camaro. Congrats clinebarger, you'll get the little things worked out over time. There always seems to be a few things that need sorting out.

08-29-2015, 12:26 AM	#72
Low Elco Registered User Join Date: Apr 2003 Location: Indep, MO Posts: 5,893	Re: '04 5.3L in a '01 V6 Camaro. How did this work out? Rubber flying in the streets of Texas? __________________ Boppa's Old Yeller Truck Build, Old Yeller's New Heart! Project Buzz Bomb Flyin' Low!



Register or Log In To remove these advertisements.

09-05-2015, 01:43 AM	#74
whitels1 Registered User Join Date: Apr 2012 Location: Vegas Posts: 617	Re: '04 5.3L in a '01 V6 Camaro. Nice work! __________________ GoldyLS1 K20 Build My K10 Rock Crawler -Dave

09-14-2015, 08:06 PM	#75
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: '04 5.3L in a '01 V6 Camaro. Finally got it finished up Saturday, Put a couple hundred miles on it so far, Very happy with it, Lights the tires at will with the old ****y touring tires, The high performance tires I have should calm that down. To do list.... Gas gauge still reads backwards....Not sure if I will/can fix that? Need to swap out the Compressor Clutch, I have a good used one. Re-torque header bolts. Buy a key fob, Open the door, The alarm goes off 'til you turn the key on. Mount & Balance tires. Car in the driveway doing final fluid checks.

Register or Log In To remove these advertisements.