Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
12-06-2017, 05:11 PM | #51 | |
Registered User
Join Date: Mar 2015
Location: Ontario Canada
Posts: 1,526
|
Re: Started My Never-Ending Project
Quote:
A trick I use to prevent powder from going where I don't want it, like the U-joint bores on the yokes, is to use aluminum tape that the HVAC guys use for sealing duct work. The trick is to remove the tape while the parts are still warm. |
|
12-07-2017, 12:53 AM | #52 |
Registered User
Join Date: Nov 2017
Location: Utah
Posts: 33
|
Re: Started My Never-Ending Project
Good to hear, I'll have to knock it out in the next few days.
|
12-11-2017, 05:20 PM | #53 |
Registered User
Join Date: Aug 2017
Location: Waggaman, La
Posts: 63
|
Re: Started My Never-Ending Project
Wow glad I found this page. I'll be watching it for sure. I'm about to pull the trigger on a 76 Blaze that has been redone but dragging my feet some.
|
12-11-2017, 05:35 PM | #54 |
Registered User
Join Date: Nov 2017
Location: Utah
Posts: 33
|
Re: Started My Never-Ending Project
Well time for a little update. I ended up powdercoating the front drive shaft a silver "bare metal" color. wasn't too big of a pain and I think it turned out good. Got the tranny and transfer case back in. Temporarily mounted the sending unit in a gas can and fired it up. It was stumbling and having a hard time running but I'm sure it was my ghetto fuel pickup connection and a filthy fuel filter by the carb. Luckily the fuel filter was a nice glass piece that I could pull apart and clean.
After filling the tranny with fluid I wanted to see how it shifted so I temp mounted the old tank back in and drove it around the block. No leaks so I am happy. I have the entire interior removed so the short drive sitting on a bucket was a little sketchy. New poly gas tank and sending unit should be here on Wednesday so I should be able to do a more thorough test later this week. Last edited by Chris_72_JIMMY; 12-11-2017 at 05:40 PM. |
12-11-2017, 07:42 PM | #55 |
Senior Member
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,762
|
Re: Started My Never-Ending Project
Chris, just a word of caution on two fronts...
first your glass filter has what appears to scratches, which is good as it is not glass. Bad, as a dropped wrench will shatter it, and a fire could develop around hot headers and manifolds or a spark from wires. hopefully the filter is plastic Second, poly tanks are not the way to go, IMHO, you have to take the neck off of your old tank, with a chisel and tin snips, then clean up the rest with a torch to get the soldier off and remove the two palnuts. The poly tank has no way of soldering on your old neck, since it is plastic You may come up with your own idea, but I haven't seen it work out yet on the boards, post up if you have a solution
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
12-11-2017, 08:30 PM | #56 | |
Registered User
Join Date: Jun 2016
Location: Vancouver, Washington
Posts: 421
|
Re: Started My Never-Ending Project
Quote:
__________________
Full top blazer or bust.... |
|
12-11-2017, 11:51 PM | #57 |
Registered User
Join Date: Dec 2017
Location: Escondido
Posts: 305
|
Re: Started My Never-Ending Project
Nice work; subscribed.
__________________
-Bruce 1971 K5 Blazer 4WD |
12-12-2017, 12:52 AM | #58 |
Registered User
Join Date: Nov 2017
Location: Utah
Posts: 33
|
Re: Started My Never-Ending Project
Thanks for the heads up fellas. The fuel filter I was just gonna chuck but after cleaning it up it looked perfect, no scratches so it must be a bad pic I have up but I will double check the material. The tank issue is no fun to hear, I was back and forth with poly vs metal and hoping I made a good purchase but this is the first I've heard of the filler neck issues. As soon as it gets here I'll post some pics.
Last edited by Chris_72_JIMMY; 12-12-2017 at 12:58 AM. |
12-12-2017, 03:28 PM | #59 |
Registered User
Join Date: Nov 2017
Location: Utah
Posts: 33
|
Re: Started My Never-Ending Project
Well, the tank showed up a day earlier than expected. Let me know what you all think.
|
12-12-2017, 08:30 PM | #60 | |
Registered User
Join Date: Jun 2016
Location: Vancouver, Washington
Posts: 421
|
Re: Started My Never-Ending Project
Quote:
The question is how much room does the angle of the filler neck leave you to hook the filler hose to the tank once the tank is in. See the pics of my repop tank it points right into the body mount so I had the old filler neck installed onto it. How wide is the filler neck when you put a tape measure on it?
__________________
Full top blazer or bust.... |
|
12-13-2017, 12:44 AM | #61 |
Registered User
Join Date: Nov 2017
Location: Utah
Posts: 33
|
Re: Started My Never-Ending Project
Tank went in tonight, the install fought me the whole way. The tank fit great and no issue with filler neck but all the little things were a pain. Put $30 worth of gas in it. No problems except i could only go to first click on pump handle. If i went full it would shut it off.
|
12-13-2017, 12:50 AM | #62 |
Registered User
Join Date: Nov 2017
Location: Utah
Posts: 33
|
Re: Started My Never-Ending Project
Glad to get it moved so I could do a little of a much needed cleanup. The aftermath of the last month was getting out of hand.
|
12-13-2017, 01:02 AM | #63 | |
Registered User
Join Date: Jun 2016
Location: Vancouver, Washington
Posts: 421
|
Re: Started My Never-Ending Project
Quote:
__________________
Full top blazer or bust.... |
|
12-13-2017, 08:20 AM | #64 | |
Senior Member
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,762
|
Re: Started My Never-Ending Project
Quote:
don't throw your old tank out, guys need the filler neck
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
|
12-13-2017, 12:22 PM | #65 |
Registered User
Join Date: Nov 2017
Location: Utah
Posts: 33
|
Re: Started My Never-Ending Project
I ended up using a 1 1/4" hose from O'reilly. It was a little spendy at $36 but it worked fine and was plenty stiff for the application. Didn't get a chance to get a pic of just the hose.
On a side note, I found out the NP205 I just spent all that time on is leaking oil out of the front drive shaft yoke. I either didn't torque it enough or didn't apply enough sealant so that's gonna be fun as there isn't much room now that's is back in the Jimmy. I have plenty of impact sockets but they are almost too thick and I need a thin wall as I think that may be why I thought it was torqued and maybe it wasn't. |
12-19-2017, 03:20 PM | #66 |
Registered User
Join Date: Nov 2017
Location: Utah
Posts: 33
|
Re: Started My Never-Ending Project
So back when I installed the new flexplate, I thought it was needed as the starter liked to skip some teeth every few start ups. So I figured the old flex plate was warped enough to cause this. With the new flexplate installed it still happens. So after some digging on the web a bunch of topics came up about the little support bracket that connects the front end of the started to the engine block can cause this. I looked at mine at lunch and sure enough mine is there but there is no nut holding it to the starter post and the bolt connecting to the block is very loose. Do any of you guys have and experience with this?
|
12-20-2017, 05:04 PM | #67 |
Registered User
Join Date: Nov 2017
Location: Utah
Posts: 33
|
Re: Started My Never-Ending Project
Well, I answered my own question. The top bolt on the starter bracket was very hard to get to but got everything tight last night. Starter turns over perfectly now, no more jumping off the flywheel. Was honestly shocked that it made that much of a difference.
|
Bookmarks |
|
|