Its Mine the World Famous 67 Dragtruck - Page 36 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

djracer · 10-03-2011, 09:23 PM

Quote:

Originally Posted by wutnxt

=================================================
Thanks for the information ....Thats hooking up pretty well and moving...You have done a great job. There aren't many trucks that will run those kinds of times....

Thanks but the previous owner did most of what was done before. He has actually been a good bit faster than I have. I hope to change that when I get back to the track!

68 C-10 KID · 10-03-2011, 09:39 PM

Quote:

Originally Posted by djracer

I'll dyno it on the track. The motor should make around 900hp and I'm gonna spray the heck out of it.

Sound like a good time to me.
Are you going with a single nozzle kit or 2 / 1 nozzle and 1 plate?
Any way you go its going to wicked evil fast.
I have never ran spray on my hot rods yet. Tuned on a bunch for people. Crazy amounts of MPH and ET gain.
I do like the man sized tire and wheels you have gone with.
So.... I see a doctors visit and some licensing passes in your future for advanced ET????

djracer · 10-03-2011, 10:15 PM

I am gonna start with just a fogger. ( I had Monte Smith he is the head tech guy for NOS plumb and tune the fogger) If I need to I will add a plate.

wutnxt · 10-03-2011, 10:39 PM

Quote:

Originally Posted by djracer

Thanks but the previous owner did most of what was done before. He has actually been a good bit faster than I have. I hope to change that when I get back to the track!

================================================
I am planning to be able to track my truck a couple of times after i get it together and dialed in...looking forward to it

djracer · 10-04-2011, 07:05 AM

Racing is very addictive. I absolutely Love it!

bigboybodry · 10-04-2011, 08:48 AM

Quote:

Originally Posted by djracer

Anti Roll Bar. I am not real sure about the bars being at an angle but it wouldn't be real hard to change if it causes a problem. The Chassis guy says the are fine.

I WANT ONE!!!!!!!!!!!!!!!!!!!!!! LOOKS GREAT DJ we all need to get together when they are all finished and have a drag down.

shawnt · 10-04-2011, 07:10 PM

Monte Smith is a bad, bad man!!
I'm sure it'll be badass... it seems if Monte does anything the car picks up crazy #'s.
I'm thinking about going with one of his or Steve Johnsons plate kits. Gotta tune it N/A first.

Have you ever sprayed using a tight 8" converter Kevin? If so, how much do you think blows through the converter?

Thanks,
Shawn

djracer · 10-04-2011, 08:57 PM

I'm not sure how much an 8 inch could take. I have run 8 inches normally aspirated with a big block but never sprayed a 8 inch convertor. I had a 9 inch in mine last time and I have a 9.5 this time.

How much are planning to spray?

djracer · 10-04-2011, 08:58 PM

Quote:

Originally Posted by bigboybodry

I WANT ONE!!!!!!!!!!!!!!!!!!!!!! LOOKS GREAT DJ we all need to get together when they are all finished and have a drag down.

Sounds like a plan to me!

shawnt · 10-05-2011, 12:12 AM

At the most a 225 shot. Just hoping it'll pick me up quite a bit. Should go 6.9x on motor maybe a little more.

Sorry about hijacking your thread ^^

djracer · 10-05-2011, 07:31 AM

Shawn I would think that you would drive through the 8 inch. Call Ptc and ask for Kenny Ford and tell him I told you to call. Give him your info and see what he says.

shawnt · 10-05-2011, 09:53 PM

LoL, which PTC? Sorry, i've seen about 5 it seems on YB but they say they're not the same. I'll give him a call though. Sucks cause I just bought the 8" ATI about a month ago.

I was thinking I would probably blow right through it also though, sucks but oh well.

djracer · 10-05-2011, 10:50 PM

http://www.ptcrace.com/torque-converters-c-26.html

djracer · 10-06-2011, 07:51 AM

A few more pics

Added a kidney bar to the cage on the passengers side

djracer · 10-06-2011, 11:28 PM

I got the axles cut down tonight. I am crossing my fingers that they fit and I don't have to have the spines cut deeper on the short axle. The long axle almost fit perfect. The pinion was not centered in the old rear end but it is now. We cut about 3/16ths off the long axle and about 2 3/4 inches off the short side axle.

shawnt · 10-07-2011, 07:23 AM

Looks good Kevin!
Posted via Mobile Device

djracer · 10-07-2011, 11:39 PM

I brought the truck home from the Chassis Shop.

Big Tall Pan Hard Bracket

16x14 Alumastars with 16x33x10.5w tire

about an inch of clearance on each side

Rear Bedside supports

Battery and Fuel pump

nxtruck · 10-08-2011, 10:27 AM

Lookin' good Kevin!! I especially like the fuel cell/ battery/ fuel pump mounting setup. Very clean looking!

dbmx66 · 10-08-2011, 08:44 PM

dj, are you putting an aluminum 3rd member in the 9 inch?

djracer · 10-08-2011, 08:58 PM

No. its nodular
Posted via Mobile Device

dbmx66 · 10-08-2011, 11:17 PM

Quote:

Originally Posted by djracer

No. its nodular
Posted via Mobile Device

oh okay, i was just wondering. i heard they save a decent amount of weight.

what gears are you putting in it anyway?

noonzor · 01-23-2012, 07:17 PM

MOAR!!!!!

haha sorry kevin I couldnt resist, I know your a busy guy.

djracer · 01-23-2012, 10:08 PM

Quote:

Originally Posted by dbmx66

oh okay, i was just wondering. i heard they save a decent amount of weight.

what gears are you putting in it anyway?

I am gonna run a 4.30 pro gear again.

I need to get this pig to the paint shop. My painters had to change locations for their business. I hope they get room in the new shop for it soon.

djracer · 04-15-2012, 11:21 PM

She is finally in the Paint Shop! Cross your fingers for me!

shortbed70 · 04-16-2012, 07:12 AM

Good luck can't wait to see it
Posted via Mobile Device

10-03-2011, 10:15 PM	#878
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck I am gonna start with just a fogger. ( I had Monte Smith he is the head tech guy for NOS plumb and tune the fogger) If I need to I will add a plate. __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

10-04-2011, 07:05 AM	#880
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck Racing is very addictive. I absolutely Love it! __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

10-04-2011, 07:10 PM	#882
shawnt Registered User Join Date: Sep 2008 Location: sulphur springs texas Posts: 141	Re: Its Mine the World Famous 67 Dragtruck Monte Smith is a bad, bad man!! I'm sure it'll be badass... it seems if Monte does anything the car picks up crazy #'s. I'm thinking about going with one of his or Steve Johnsons plate kits. Gotta tune it N/A first. Have you ever sprayed using a tight 8" converter Kevin? If so, how much do you think blows through the converter? Thanks, Shawn __________________ Shawn 85 SWB 7.39 @ 93 Best so far with 0 tuning Lesson in life: Never fry bacon naked!

10-04-2011, 08:57 PM	#883
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck I'm not sure how much an 8 inch could take. I have run 8 inches normally aspirated with a big block but never sprayed a 8 inch convertor. I had a 9 inch in mine last time and I have a 9.5 this time. How much are planning to spray? __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

10-05-2011, 12:12 AM	#885
shawnt Registered User Join Date: Sep 2008 Location: sulphur springs texas Posts: 141	Re: Its Mine the World Famous 67 Dragtruck At the most a 225 shot. Just hoping it'll pick me up quite a bit. Should go 6.9x on motor maybe a little more. Sorry about hijacking your thread ^^ __________________ Shawn 85 SWB 7.39 @ 93 Best so far with 0 tuning Lesson in life: Never fry bacon naked!

10-05-2011, 07:31 AM	#886
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck Shawn I would think that you would drive through the 8 inch. Call Ptc and ask for Kenny Ford and tell him I told you to call. Give him your info and see what he says. __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

10-05-2011, 09:53 PM	#887
shawnt Registered User Join Date: Sep 2008 Location: sulphur springs texas Posts: 141	Re: Its Mine the World Famous 67 Dragtruck LoL, which PTC? Sorry, i've seen about 5 it seems on YB but they say they're not the same. I'll give him a call though. Sucks cause I just bought the 8" ATI about a month ago. I was thinking I would probably blow right through it also though, sucks but oh well. __________________ Shawn 85 SWB 7.39 @ 93 Best so far with 0 tuning Lesson in life: Never fry bacon naked!

10-05-2011, 10:50 PM	#888
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck http://www.ptcrace.com/torque-converters-c-26.html __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

10-06-2011, 07:51 AM	#889
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck A few more pics Added a kidney bar to the cage on the passengers side __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

10-06-2011, 11:28 PM	#890
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck I got the axles cut down tonight. I am crossing my fingers that they fit and I don't have to have the spines cut deeper on the short axle. The long axle almost fit perfect. The pinion was not centered in the old rear end but it is now. We cut about 3/16ths off the long axle and about 2 3/4 inches off the short side axle. __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

10-07-2011, 07:23 AM	#891
shawnt Registered User Join Date: Sep 2008 Location: sulphur springs texas Posts: 141	Re: Its Mine the World Famous 67 Dragtruck Looks good Kevin! Posted via Mobile Device __________________ Shawn 85 SWB 7.39 @ 93 Best so far with 0 tuning Lesson in life: Never fry bacon naked!

10-07-2011, 11:39 PM	#892
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck I brought the truck home from the Chassis Shop. Big Tall Pan Hard Bracket 16x14 Alumastars with 16x33x10.5w tire about an inch of clearance on each side Rear Bedside supports Battery and Fuel pump __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

10-08-2011, 10:27 AM	#893
nxtruck Registered User Join Date: Jun 2006 Location: Jackson, Mo. Posts: 607	Re: Its Mine the World Famous 67 Dragtruck Lookin' good Kevin!! I especially like the fuel cell/ battery/ fuel pump mounting setup. Very clean looking! __________________ Chris 1966 Chevy C10 LWB, 434 sbc, TH350, 12-bolt, factory suspension, pump gas 7.02 @ 95.8, 1.45 60' 1965 Chevy C10 LWB, 355 sbc, TH350, daily driver

10-08-2011, 08:44 PM	#894
dbmx66 Registered User Join Date: Aug 2009 Location: PA Posts: 883	Re: Its Mine the World Famous 67 Dragtruck dj, are you putting an aluminum 3rd member in the 9 inch?

10-08-2011, 08:58 PM	#895
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck No. its nodular Posted via Mobile Device __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!



Register or Log In To remove these advertisements.

01-23-2012, 07:17 PM	#897
noonzor Registered User Join Date: Aug 2009 Location: Edmonton, Alberta Posts: 818	Re: Its Mine the World Famous 67 Dragtruck MOAR!!!!! haha sorry kevin I couldnt resist, I know your a busy guy. __________________ 69 c10 Shortbox Build http://67-72chevytrucks.com/vboard/s...d.php?t=360622

04-15-2012, 11:21 PM	#899
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: Its Mine the World Famous 67 Dragtruck She is finally in the Paint Shop! Cross your fingers for me! __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

04-16-2012, 07:12 AM	#900
shortbed70 Registered User Join Date: Mar 2002 Location: Forney TX Posts: 4,512	Re: Its Mine the World Famous 67 Dragtruck Good luck can't wait to see it Posted via Mobile Device __________________ Troy 1965 Chevy Bagged,361 sbc,voodoo cam,1.5 full roller rockers,patriot 185cc vortec heads 2.02-1.60,vortec weiand polished intake,demon carb my truckhttp://67-72chevytrucks.com/vboard/s...d.php?t=332884 Big Red Dog build http://67-72chevytrucks.com/vboard/s...d.php?t=572274

Register or Log In To remove these advertisements.