Another way to skin the cat; the High Torque 292 LS swap - Page 8 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**dayj1** · 01-29-2019, 11:48 AM

Quote:

Originally Posted by Dads79GMC

How are your truck injectors working in the fuel rail and intake.

The injectors worked fine. I think I had to pop the plastic caps off the end to get them to slip into the intake, but it's been so long I can't remember.

**Dads79GMC** · 01-29-2019, 12:27 PM

I’m a self taught gearhead. So, I know the injector bottoms out in the intake, then I slightly brought it back ever so slightly. So the end cap comes off and the injector, then should protrude through the base of the intake? Thanks Mike

**mongocanfly** · 01-29-2019, 12:50 PM

yep Jonathon...you removed the black plastic end...at least that's what you told me to do on mine....haha

**dayj1** · 01-29-2019, 03:30 PM

Quote:

Originally Posted by Dads79GMC

I’m a self taught gearhead. So, I know the injector bottoms out in the intake, then I slightly brought it back ever so slightly. So the end cap comes off and the injector, then should protrude through the base of the intake? Thanks Mike

As long as it seals on the o ring, you're good (at least from a no-leak perspective). But, in some intakes, the cap on the end of the truck injector stops it from pushing into the intake far enough to seal. So you have to remove the caps. They'll pull of with a pair of pliers.

Quote:

Originally Posted by mongocanfly

yep Jonathon...you removed the black plastic end...at least that's what you told me to do on mine....haha

Thanks for the reminder!

**Dads79GMC** · 01-29-2019, 04:13 PM

I appreciate all the help!! Thanks Mike

LT7A · 01-30-2019, 12:40 AM

Wow, I really enjoyed reading this. Style and taste are individual, but combined with ingenuity, the appeal is universal. I hope to see more on this truck. Thanks for sharing.

**Captainfab** · 04-14-2019, 10:56 PM

I really like what you did with your truck build.....nice job

72GreenMonster · 04-24-2019, 02:11 AM

Joining the swap community but the simplicity and fabrication is top notch.
Tell us your really a 🚀 scientist and if not your work and detail is worthy of one. Thanks for sharing. My swap may never match up but the bar has been set. Next read is lsnova.
Thanks again

solidaxel · 04-24-2019, 10:30 AM

LS1Nova your PM box is full
I have a question for you!

**dayj1** · 04-26-2019, 12:50 AM

Quote:

Originally Posted by Captainfab

I really like what you did with your truck build.....nice job

Thank you!

Quote:

Originally Posted by 72GreenMonster

Joining the swap community but the simplicity and fabrication is top notch.
Tell us your really a 🚀 scientist and if not your work and detail is worthy of one. Thanks for sharing. My swap may never match up but the bar has been set. Next read is lsnova.
Thanks again

I'm not a rocket scientist, but I do work for the folks who put the first man on the moon.

Thanks for the kind words.

**mattfranklin** · 05-03-2019, 12:28 PM

Wow! Beautiful work. The vision, the fab, and the pics. Everything top notch.

**chev-obsession** · 05-08-2019, 02:40 PM

What exhaust manifolds did you use?

**dayj1** · 05-08-2019, 04:28 PM

Quote:

Originally Posted by mattfranklin

Wow! Beautiful work. The vision, the fab, and the pics. Everything top notch.

Thanks!

Quote:

Originally Posted by chev-obsession

What exhaust manifolds did you use?

LS3 Camaro manifolds.

gringoloco · 05-09-2019, 12:20 AM

Just wanted you to know this thread is a giver. I’ve used it twice in the last week, once plumbing fuel lines and once cutting radiator hoses. Thanks!

**Dads79GMC** · 05-09-2019, 01:10 AM

Quote:

Originally Posted by gringoloco

Just wanted you to know this thread is a giver. I’ve used it twice in the last week, once plumbing fuel lines and once cutting radiator hoses. Thanks!

So true!!!!!!

Willie Makeit · 05-09-2019, 02:04 PM

Quote:

Originally Posted by gringoloco

Just wanted you to know this thread is a giver. I’ve used it twice in the last week, once plumbing fuel lines and once cutting radiator hoses. Thanks!

I know dayj1 personally and he is that way with his time and his knowledge in the "real world" too.

Just a dang good dude all around & I'm lucky to be able to call him a friend.

**dayj1** · 05-10-2019, 10:30 AM

Quote:

Originally Posted by gringoloco

Just wanted you to know this thread is a giver. I’ve used it twice in the last week, once plumbing fuel lines and once cutting radiator hoses. Thanks!

Quote:

Originally Posted by Dads79GMC

So true!!!!!!

I'm glad it's getting some use!

Quote:

Originally Posted by Willie Makeit

I know dayj1 personally and he is that way with his time and his knowledge in the "real world" too.

Just a dang good dude all around & I'm lucky to be able to call him a friend.

Thanks! I don't think there are many of us who do everything to our trucks by ourselves. I know my projects wouldn't turn out as well as they do nor be finished as quickly if I didn't have help from my friends. And, of course, that includes all the side projects I send your way!

incoma · 07-04-2022, 07:29 PM

Quote:

Originally Posted by dayj1

and more...

Is there a disadvantage of just converting a 71-72 style fuel sending unit to a return/feed system? I've noticed a few guys adding an extra inlet/outlet to the tank. I was going to convert a 71-72 over... but I'm second guessing myself now.

**dayj1** · 07-05-2022, 03:50 PM

Quote:

Originally Posted by incoma

Is there a disadvantage of just converting a 71-72 style fuel sending unit to a return/feed system? I've noticed a few guys adding an extra inlet/outlet to the tank. I was going to convert a 71-72 over... but I'm second guessing myself now.

Packaging was the big reason for me. Incorporating a feed and a return line and the appropriate bulkheads for the pump and the sender is a lot to put in a stock sending unit as it's pretty small. It'd also be tough to get a pump and float through the stock hole in the tank.

I'm sure the stock sender could be modified to work, but I went with what I thought was an easier/better alternative for me.

incoma · 07-05-2022, 04:00 PM

Thanks
Posted via Mobile Device

larryboy_3t5 · 12-23-2022, 07:55 PM

Hey, looking to do a similar swap and my issue is leg room in the cab. It looks like you had plenty of room in that area behind the driver's side cylinder head to mount your coils. If I didn't do that, would I be able to push that area of the firewall, where the throttle pedal attaches, forward an inch or two without interfering with the back of the engine? It almost looks like the firewall could be flush all the way across behind the engine in your photos.

01-29-2019, 12:27 PM	#177
Dads79GMC Senior Member Join Date: Feb 2008 Location: Des Moines, Iowa Posts: 1,238	Re: Another way to skin the cat; the High Torque 292 LS swap I’m a self taught gearhead. So, I know the injector bottoms out in the intake, then I slightly brought it back ever so slightly. So the end cap comes off and the injector, then should protrude through the base of the intake? Thanks Mike __________________ Instagram @HomeBuiltC10s Dads 79 GMC Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=642929 1978 Silverado Build http://67-72chevytrucks.com/vboard/s...d.php?t=756016

01-29-2019, 12:50 PM	#178
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: Another way to skin the cat; the High Torque 292 LS swap yep Jonathon...you removed the black plastic end...at least that's what you told me to do on mine....haha __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

01-29-2019, 04:13 PM	#180
Dads79GMC Senior Member Join Date: Feb 2008 Location: Des Moines, Iowa Posts: 1,238	Re: Another way to skin the cat; the High Torque 292 LS swap I appreciate all the help!! Thanks Mike __________________ Instagram @HomeBuiltC10s Dads 79 GMC Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=642929 1978 Silverado Build http://67-72chevytrucks.com/vboard/s...d.php?t=756016

01-30-2019, 12:40 AM	#181
LT7A Registered User Join Date: Oct 2015 Location: PNW Posts: 3,626	Re: Another way to skin the cat; the High Torque 292 LS swap Wow, I really enjoyed reading this. Style and taste are individual, but combined with ingenuity, the appeal is universal. I hope to see more on this truck. Thanks for sharing.

04-14-2019, 10:56 PM	#182
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: Another way to skin the cat; the High Torque 292 LS swap I really like what you did with your truck build.....nice job __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

04-24-2019, 02:11 AM	#183
72GreenMonster Registered User Join Date: Dec 2018 Location: Los Angeles Posts: 53	Re: Another way to skin the cat; the High Torque 292 LS swap Joining the swap community but the simplicity and fabrication is top notch. Tell us your really a 🚀 scientist and if not your work and detail is worthy of one. Thanks for sharing. My swap may never match up but the bar has been set. Next read is lsnova. Thanks again __________________ 72 GMC Sierra 2500

04-24-2019, 10:30 AM	#184
solidaxel Registered User Join Date: Dec 2002 Location: Cactus Patch So. Az Posts: 4,749	Re: Another way to skin the cat; the High Torque 292 LS swap LS1Nova your PM box is full I have a question for you! __________________ 53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42

05-03-2019, 12:28 PM	#186
mattfranklin Senior Member Join Date: Dec 2011 Location: Moraga, CA Posts: 812	Re: Another way to skin the cat; the High Torque 292 LS swap Wow! Beautiful work. The vision, the fab, and the pics. Everything top notch. __________________ (Very) Slow-Going Build Thread: Stock 1970 Short Step with Stock 1970 LT-1 http://67-72chevytrucks.com/vboard/s...d.php?t=567340

05-08-2019, 02:40 PM	#187
chev-obsession Senior Member Join Date: Jul 2008 Location: kennewick, WA Posts: 1,513	Re: Another way to skin the cat; the High Torque 292 LS swap What exhaust manifolds did you use? __________________ 1965 c/10 swb 1969 c/10 lwb

05-09-2019, 12:20 AM	#189
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: Another way to skin the cat; the High Torque 292 LS swap Just wanted you to know this thread is a giver. I’ve used it twice in the last week, once plumbing fuel lines and once cutting radiator hoses. Thanks! __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

07-05-2022, 04:00 PM	#195
incoma Registered User Join Date: Mar 2004 Location: Lexington, KY Posts: 865	Re: Another way to skin the cat; the High Torque 292 LS swap Thanks Posted via Mobile Device

12-23-2022, 07:55 PM	#196
larryboy_3t5 Registered User Join Date: May 2010 Location: Meridian, Idaho, USA Posts: 54	Re: Another way to skin the cat; the High Torque 292 LS swap Hey, looking to do a similar swap and my issue is leg room in the cab. It looks like you had plenty of room in that area behind the driver's side cylinder head to mount your coils. If I didn't do that, would I be able to push that area of the firewall, where the throttle pedal attaches, forward an inch or two without interfering with the back of the engine? It almost looks like the firewall could be flush all the way across behind the engine in your photos. __________________ "A man's got to know his limitations" 1969 Chevy C20 Camper Special 1968 Chevy C-10 short/fleet 1970 GMC Jimmy 4x4 (SOLD)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.