Danny Boy is BAACK! w/ '55 Big Window

[Russell Ashley]

Dan, this is what I was referring to. The first bolt holding the angle strip to the bed side goes into the stake pocket so the nut is not visible on the outside. The cross sill bolts are about two inches back so the nut on a bolt through the bed side there would show. The others can be aligned with the cross sills.

[Dan in Pasadena]

Thanks Russ, yes I understand.

[Dan in Pasadena]

Friday, September 29, 2017

Ok, so the truck WOULD HAVE BEEN ready to test drive around the block today except when they went to install the driveshaft it was too long! Mike had sent 3 out for modifiction to a new shop and all of them were too long.

So he read the guy the riot act and it was supposed to be modified and returned by noon today - but it wasn't there by 1pm when I got there.

The only thing it will need after the driveshaft is installed is to put the ignition switch back in the dash and tie up some loose wires that will be terminated later when the bed is installed.

So the journey continues...............

[oldman3]

Sorry buddy on the delay, but you'll get there...Jim

[joedoh]

oh man, so close!

[Dan in Pasadena]

Hey, does anyone have the link for the aftermarket place that makes the cowl grill delete panel for Task Force trucks? I know I've seen it. Can't recall if it's metal or fiberglas but I'm considering using one afterall.

[G&R's57GMC]

Brotherstrucks has one cp159sm on sale now $ 79

[Dan in Pasadena]

Thanks Glen; purchased.

Stopped by the shop today - Trying to keep the pressure on to get the truck delivered. Comes home Mon/Tues til a problem w/spray booth is worked out.

1. Bedsides need 1 more coat of clear on 1 side.
2. Tailgate, front panel & vent delete panel need to be painted.
3. Mount & adjust hood
4. Install all glass
5. Truck to upholstery shop for interior work.

Somewhere in all this the grill, badges, seat belts, tail gate chains, and assorted details will get installed.

At this rate the truck is looking like it'll be a Christmas present to myself.

[G&R's57GMC]

Hay Dan don't ya love the internet ! Ask , Answer, Get , Post

[Dan in Pasadena]

The internet? Mostly yes, occasionally no. It has caused me to spend more money easily than I ever did before!

Summit had the vent panel on eBay for $65.99 with free shipping. Wouldn't have found that price without the interwebs!

[ChuckDriver]

Let's hope it's an early Christmas present!!

[Black_Sheep]

Test fit the cowl vent replacement panel before paint, mine needed a little massaging to fit the wiper pivots properly.

[Dan in Pasadena]

Originally Posted by Black_Sheep

Test fit the cowl vent replacement panel before paint, mine needed a little massaging to fit the wiper pivots properly.

Good advice, thanks.

Since I'm switching to this to prevent water, leaves ,etc from entering should I use some kind of gasket? The factory onenever had a gasket. Maybe a bead of silicone-allowed-to-dry first as a gasket?

[Black_Sheep]

Originally Posted by Dan in Pasadena

Good advice, thanks.

Since I'm switching to this to prevent water, leaves ,etc from entering should I use some kind of gasket? The factory onenever had a gasket. Maybe a bead of silicone-allowed-to-dry first as a gasket?

The edges on the side are just rolled over sheet metal so there isn't really a good surface to seal to. If you are dead set on sealing it, instead of silicone I would use strip caulk because it will remain pliable.

[Dan in Pasadena]

Originally Posted by Black_Sheep

The edges on the side are just rolled over sheet metal so there isn't really a good surface to seal to. If you are dead set on sealing it, instead of silicone I would use strip caulk because it will remain pliable.

I did a bad job of describing what I'm thinking.

1st: I don't think I'll ever turn a hose on the truck or intentionally drive it in serious rain (it' SOCal, "serious rain"? C'mon! lol) So I don't think it will ever see very much water to keep out.

2nd: Like I did on my transmission cover I'd run a heavy bead of silicone on the mating surface and allow it to thoroughly cure. THEN I'd bolt the vent cover down so the silicone acts as a flexible seal or gasket.

Totally agree on "remaining pliable" Using the silicone as a permanent seal would bea cheesy bad idea.

[lower50's]

Well that sucks! But a Christmas present isn't all bad.

[Kim57]

Nice looking panel.
Kim

[bowt1ed]

Dan, same one I got from Dynacorn. Fits pretty well, but you may have to massage the mounting holes just a bit to get it to center just right. I tried to find a pic of mine. Good piece.

Cheers, Jim

[Dan in Pasadena]

Thanks Jim,
I'll drop the panel off with the painter today and get the latest (as if it'll change!) on when the bed side panel painting will be complete, plus the front panel and tail gate.

Mike texted last night that we'll take a short test drive around the block today. I'm waiting to hear from him, head over to the shop so I can video it. Then I'll flat bed tow it home (9 mi, no glass, no brake lights or door handles, etc) when I'd prefer to drive it on the back roads - then adult thought kicked in and I decided I'd better not - DAMN!

THEN, I'll take the bench seat back to upholsterer and W...A...I...T...!...!

EDIT:
Test drove her down the street 2 blocks. No, forum STILL won't let me load the video!
Runs great. Has a nice low stance but will be adjusted when bed is on. It's quieter (but not quiet) than I thought it would be. Tiny coolant leak to be fixed. Buttonhead Allen screw on Borgeson joint rubs exhaust tubing. Need a 1/8" - 1/4" dimple in exhaust to clear. Brake pedal arm rubs hole in floor, needs adjustment. To be continued...

[Black_Sheep]

There will always be things to sort out on a fresh build, thankfully it all sounds like minor stuff.

[ChuckDriver]

The first drive is always fun, congrats!!

[oldman3]

Dan, congrats on driving your truck...Jim

[joedoh]

woooooooot way to go idaho

for the video, its probably too large. the forum software was probably written when camera phones were 0.3MP but now you can shoot 1080p. there was a free program that came with windows called windows movie maker, it doesnt come with it any more BUT you can find it on the web for free. import the video, then save it, then export it as a 480p. it should be small enough to upload. on a mac, photos lets you do this.

either way, you can upload it to youtube and post it, I can help you if thats what you wanna do, just shoot me a pm.

[murd969]

Good looking build.

[Dan in Pasadena]

Thanks Joedoh. I posted the video on Facebook but that's no help for this. I'll keep trying. I'll figure it out eventually. I suffer from "Lame Old Dude-itis" when it comes to technological stuff, lol