How do I get the glass out??? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67chevemall · 12-17-2004, 10:15 AM

Hello
Just wondering the easiest way to get the front and rear glass out?
The back window is a slider and I want to take the whole unit out as one!
Thanks in advance!

bigblock73 · 12-17-2004, 10:54 AM

front, pull the lock strip out of the weatherstripping channel, then push out the window. Rear, cut the gasket and pull/push out the window assembly

Jonboy · 12-17-2004, 11:27 AM

If the rear has a lock strip, it should come out similar to the front. If you cut the gasket, you will need a new one.

full foot notch · 12-17-2004, 11:27 AM

swift kick with a steel toe boot attached to you foot?, hey you said as an assembly, but really, i would either say use big suction cup glass pullers and remove the seals, or just get some piano wire on wood dowels and push one end thru and pretty much saw thru the front seal with the wire

sometimes if you can find a glass guy off of work but with thier van, offer like 20-30 to pull the glass and all, or at least cut the seals with the proper tools

bigblock73 · 12-17-2004, 01:50 PM

Quote:

Originally Posted by Jonboy

If the rear has a lock strip, it should come out similar to the front. If you cut the gasket, you will need a new one.

Did any of the rear windows on our trucks come with a lock strip? All the ones I have seen have not had them.

When pulling or putting in new windows, I usually use new seals...safe insurance against leaks plus new ones look so much better.

C-10volvo · 12-17-2004, 03:32 PM

Quote:

Originally Posted by bigblock73

Did any of the rear windows on our trucks come with a lock strip? All the ones I have seen have not had them.

When pulling or putting in new windows, I usually use new seals...safe insurance against leaks plus new ones look so much better.

mine did

its quite hard to see without the chrome peice in there. a box from lmc showed up yesterday with all new rubber for everything. YESS

Jonboy · 12-17-2004, 08:10 PM

Another bit of advice, if there has ever been any sealant put in the channel, make sure you put more in. It will leak terribly if none is put in. If there has never been any put in, you should be fine. I usually change the chrome lock strip to black for two reasons. The chrome plastic gets really brittle with age, and will most like y need to be replaced, and because I like the way the black looks compared to the chrome. There were actually 3 different looks, the early "Custom" trim level trucks did not use the lockstrip, but had a flap that folded over and locked the rubber into place. My 73 had that, and it has a cleaner look than the locking strip type, IMO.

72 CustomCamper · 12-17-2004, 10:18 PM

Quote:

Originally Posted by bigblock73

Did any of the rear windows on our trucks come with a lock strip? All the ones I have seen have not had them.

My 86 has a lock strip on the rear window...

Chuck

*1FaastC10* · 12-17-2004, 11:49 PM

Quote:

Originally Posted by 72 CustomCamper

My 86 has a lock strip on the rear window...

as does mine.

12-17-2004, 10:15 AM	#1
67chevemall Registered User Join Date: Apr 2003 Location: NB Posts: 3,367	How do I get the glass out??? Hello Just wondering the easiest way to get the front and rear glass out? The back window is a slider and I want to take the whole unit out as one! Thanks in advance! __________________ 1968 Chevy C10 307 3ott fleetside 1967 Chevy C/10 V8, 3spd, fleetside lwb.Sold 1967 Chev C/10 step, 383, M21. SOLD

12-17-2004, 10:54 AM	#2
bigblock73 yeller Join Date: Oct 2001 Location: Twin Cities Posts: 13,824	front, pull the lock strip out of the weatherstripping channel, then push out the window. Rear, cut the gasket and pull/push out the window assembly __________________ Jeff 73-87.com 73-87.com Facebook page 73-87 cab corner 6x9 speaker brackets for sale 67-72 cab corner speaker brackets for sale 47-54 cab corner speaker brackets for sale

12-17-2004, 11:27 AM	#3
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	If the rear has a lock strip, it should come out similar to the front. If you cut the gasket, you will need a new one. __________________ 1974 Jimmy- 5.3/4L80e/NP241

12-17-2004, 08:10 PM	#7
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Another bit of advice, if there has ever been any sealant put in the channel, make sure you put more in. It will leak terribly if none is put in. If there has never been any put in, you should be fine. I usually change the chrome lock strip to black for two reasons. The chrome plastic gets really brittle with age, and will most like y need to be replaced, and because I like the way the black looks compared to the chrome. There were actually 3 different looks, the early "Custom" trim level trucks did not use the lockstrip, but had a flap that folded over and locked the rubber into place. My 73 had that, and it has a cleaner look than the locking strip type, IMO. __________________ 1974 Jimmy- 5.3/4L80e/NP241

12-17-2004, 11:27 AM	#4
full foot notch Registered User Join Date: Apr 2003 Location: Central florida Posts: 3,223	swift kick with a steel toe boot attached to you foot?, hey you said as an assembly, but really, i would either say use big suction cup glass pullers and remove the seals, or just get some piano wire on wood dowels and push one end thru and pretty much saw thru the front seal with the wire sometimes if you can find a glass guy off of work but with thier van, offer like 20-30 to pull the glass and all, or at least cut the seals with the proper tools



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.