How many trucks did it take to make yours? - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

mike nutt · 05-17-2006, 05:46 AM

9 or 10 , loosing count !!!! finding all the parts you need is half the fun.

GM72K10 · 05-17-2006, 06:20 AM

For the 72 K10: 3 big pieces and maybe 10 more for all the little stuff
70 Chassis
72 Suburban Transfer, trans, rears
72 Donor Cab

69TowRig · 05-20-2006, 01:50 PM

I've barely done anything to mine yet and there are at least a dozen truck's parts on it so far. How's that go, only the strong survive? Sometimes the strong prey on the weak...

DangerBoy · 05-20-2006, 03:36 PM

Engine from a 74 blazer
Tranny out of an early 80's el camino
Rear end pulled from a 94 GMC
Front discs salvaged out of a wrecked 71 c10
At one time I had a rear bumper from a mid 80's wagon.
Numerous tailgates and then a big hit-me-and-die bumper from a c20
Radiator out of a 67 GMC
Air cleaner spacer from a caddillac el dorado. Probably should have looked to see what size that particular engine was....
I feel an urge to take a ride down the the boneyard comming on.

05-17-2006, 05:46 AM	#26
mike nutt 69fatmotor Join Date: Oct 2005 Location: bama Posts: 660	Re: How many trucks did it take to make yours? 9 or 10 , loosing count !!!! finding all the parts you need is half the fun.

05-17-2006, 06:20 AM	#27
GM72K10 Next! Join Date: Jan 2003 Location: Eastern Pa. Posts: 2,483	Re: How many trucks did it take to make yours? For the 72 K10: 3 big pieces and maybe 10 more for all the little stuff 70 Chassis 72 Suburban Transfer, trans, rears 72 Donor Cab __________________ 86 K30 CUCV M1028A1 86 K30 CUCV M1028a2 dually 86 K30 C&C 6.2 4:56s, 4M, 11,000 gvw, ex fire truck, now lowboy dump More square bodies and CUCVs than I care to admit to 2020 Silverado K3500HD Work truck

05-20-2006, 01:50 PM	#28
69TowRig Senior Member Join Date: Jan 2005 Location: Raleigh, NC Posts: 894	Re: How many trucks did it take to make yours? I've barely done anything to mine yet and there are at least a dozen truck's parts on it so far. How's that go, only the strong survive? Sometimes the strong prey on the weak... __________________ -Chris Building a stripper, one part at a time: 1969 K5, 307, 3spd, 3 seats, hard top. Added Pwr Discs, Pwr Steering, Aux Battery, T-case Skid, Lighted Sidemarkers, HEI, Lock-Right Diff, ECE Class IV Hitch, 32" MT/Rs. Parts to Install: Hand Throttle, Console, Tow Hooks, Dual Horns, AM-FM, Dealer Swing-Away Tire Carrier, Gas Tank Skid. Also building a 1950 Willys CJ-3A and off-roading a 2001 Nissan Frontier on 1-Ton Portals...

05-20-2006, 03:36 PM	#29
DangerBoy Registered User Join Date: Nov 2005 Location: Springville, Ca Posts: 270	Re: How many trucks did it take to make yours? Engine from a 74 blazer Tranny out of an early 80's el camino Rear end pulled from a 94 GMC Front discs salvaged out of a wrecked 71 c10 At one time I had a rear bumper from a mid 80's wagon. Numerous tailgates and then a big hit-me-and-die bumper from a c20 Radiator out of a 67 GMC Air cleaner spacer from a caddillac el dorado. Probably should have looked to see what size that particular engine was.... I feel an urge to take a ride down the the boneyard comming on. __________________ 2002 S10 ZR2 for the dirt. 1968 C10 shorty for the street. She said the truck would be the end of us. I still have the truck!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.