|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
05-30-2006, 06:05 PM
|
#1 |
|
Keep On Keepin' On
Join Date: Apr 2006
Location: Oklahoma
Posts: 416
|
Decided on 3/5 drop...Question..
OK...After reviewing and looking at numerous posts on this board, I have decided to go with a 3/5 drop..I want to do it the right way and go with spindles (so people have told me spindles are the right way)...I have only seen 2.5 spindles, what would I need to do with my existing springs to get that extra half inch...Cut or heat up? Also, on the rear, with 5 inch springs what are my "must haves" and my "do it right" items..Thanks for the input....
|
|
|
|
05-30-2006, 07:02 PM
|
#2 |
|
Shaved
Join Date: Nov 2004
Location: Vernon, Tx
Posts: 115
|
Re: Decided on 3/5 drop...Question..
Well just to let you know, "do it right" and "cut/heat springs" don't usually go hand-in-hand. Just buy 3in coils.
__________________
1969 
|
|
|
|
|
05-30-2006, 08:01 PM
|
#3 |
|
Registered User
Join Date: Mar 2005
Location: Las Vegas, NV
Posts: 84
|
Re: Decided on 3/5 drop...Question..
DJM sells 3'' spindles. They are for 73-87 so you would need to make a couple of changes to some front end parts. but then you won't have to cut anything. You didn't say what year your truck was, but if it has drum brakes this is way to upgrade to disc.
|
|
|
|
|
05-30-2006, 09:35 PM
|
#4 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: Decided on 3/5 drop...Question..
A 1/2 isn`t worth worrying about.If you want to go with spindles,they are 2 1/2".There`s nothing wromg with up to 3" springs.It`s when you want more,like 4",that you need to combime spindles & springs(spindles 2 1/2"/springs 1 1/2").
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
05-30-2006, 11:47 PM
|
#5 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
|
Re: Decided on 3/5 drop...Question..
BellTech & DJM both offer 3" spindles & Western Chassis has 2.5" spindles.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
05-31-2006, 11:00 PM
|
#6 |
|
Special Order
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: Decided on 3/5 drop...Question..
Yeah,the spindles are either 2 1/2" or 3".I`m just saying 1/2" is nothing to squabble about.I mean,it`s like the width of the tip of your pinky.And,there`s nothing "wrong" about using -3" springs or less.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
