The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-04-2006, 08:03 PM   #1
laidout86
Registered User
 
Join Date: Dec 2005
Location: sarasota florida
Posts: 24
control arms needed?

hey guys whats goin on...i just recently put on my new rims/tires and it lifted the front end up..im runnin a 265/35/22 and was wondering if im gonna need tubular control arms to get the front to lay out..right now the crossmember is about 2 inchs or so off the ground..i want to get the crossmember laid out first so i dont have to make a bigger z than have too...thanks alot guys!
laidout86 is offline   Reply With Quote
Old 08-04-2006, 10:27 PM   #2
XXL
Seņor Member
 
XXL's Avatar
 
Join Date: May 2002
Location: Edge of the world
Posts: 5,367
Re: control arms needed?

Tubular control arms aren't going to give you any additional clearance.
XXL is offline   Reply With Quote
Old 08-05-2006, 12:32 AM   #3
bagged69c10
soon to be bagged64sub
 
bagged69c10's Avatar
 
Join Date: Feb 2005
Location: DFW-currently phoenix
Posts: 635
Re: control arms needed?

If you get plenty of lift I would check into cutting down the bottom cup a bit. Just make sure it wont rub if you cut it down. Im assuming you have spindles already and an upper plate, lower cup setup.
__________________
1969 c-10, bagged, Zd, 20" Boyds SOLD!
1964 Suburban COMING SOON Build threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=304726
1965 c-10 long bed
1993 Sierra x-cab
1999 tahoe-4/5 on 22s
2005 Chevy work truck
bagged69c10 is offline   Reply With Quote
Old 08-05-2006, 01:39 AM   #4
laidout86
Registered User
 
Join Date: Dec 2005
Location: sarasota florida
Posts: 24
Re: control arms needed?

yea have that already and the bottom cup is cut down to 1 inch already
laidout86 is offline   Reply With Quote
Old 08-05-2006, 04:31 PM   #5
7deuce
Sold! 2 days after finished
 
7deuce's Avatar
 
Join Date: Oct 2005
Location: Ohio
Posts: 327
Re: control arms needed?

Take out the lower cup and weld a flat plate in the control arm. That might get you another inch.
7deuce is offline   Reply With Quote
Old 08-06-2006, 12:50 AM   #6
camaro__thunder
Epoxy Primer Friendly
 
camaro__thunder's Avatar
 
Join Date: Feb 2004
Location: South of Houston TEXXXAS
Posts: 680
Re: control arms needed?

If the truck is an 86 you dont need a lower cup just bolt it to the LCA. They are big enough. Just make sure to debur it and clean it all up.
__________________
My Project 69 SWB
SHAVED BAGGED DOORED
camaro__thunder is offline   Reply With Quote
Old 08-06-2006, 04:42 PM   #7
laidout86
Registered User
 
Join Date: Dec 2005
Location: sarasota florida
Posts: 24
Re: control arms needed?

i just ordered lowers so as soon as i get them im gonna put them in and see if it helps....im gonna put them in without the cup also so.....
laidout86 is offline   Reply With Quote
Old 08-08-2006, 11:29 AM   #8
Tony@AirRideTech
Junior Member
 
Join Date: Feb 2005
Location: Huntingburg IN
Posts: 620
Re: control arms needed?

Quote:
Originally Posted by laidout86
hey guys whats goin on...i just recently put on my new rims/tires and it lifted the front end up..im runnin a 265/35/22 and was wondering if im gonna need tubular control arms to get the front to lay out..right now the crossmember is about 2 inchs or so off the ground..i want to get the crossmember laid out first so i dont have to make a bigger z than have too...thanks alot guys!
Are you also running dropped spindles on the truck?
Tony@AirRideTech is offline   Reply With Quote
Old 08-08-2006, 04:19 PM   #9
Shane
Account Suspended
 
Shane's Avatar
 
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
Re: control arms needed?

...

Last edited by Shane; 08-08-2006 at 04:20 PM.
Shane is offline   Reply With Quote
Old 08-08-2006, 05:04 PM   #10
laidout86
Registered User
 
Join Date: Dec 2005
Location: sarasota florida
Posts: 24
Re: control arms needed?

yea i got 3 inch drop spinedles on there with a suicidedoors upper plate with a slam re-82

Last edited by laidout86; 08-08-2006 at 05:04 PM.
laidout86 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:40 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com