'92 Gmc Suburban

[69c10stepside]

Originally Posted by keenee

My bumper is rottten, I think the brackets will be ok. Thanks

I am not able to get a good shipping quote for this, everything is coming back too expensive for me. Did you have any luck on this?

[bagged91]

Originally Posted by 69c10stepside

I would really like to keep the door panels together if at all possible, what kind of value are you putting on these parts? I haven't tore a suburban down to the point of pulling out the harness like you are asking before, might be a bit of a learning curve on some of that

What kind of parts do you have that you would want to trade?

Hi Frank,
The wiring harness is pretty easy from what I remember. Remove steering column. Remove the screws across the top of the dash(5 or 6 I think). Remove the 2 bolts on the bottom sides of the dash so that the dash will now swing down on your lap. It is now very easy to unplug at convienence center. Across the bottom of the windshield, there are clips spotwelded to the firewall. Bend them down slightly to remove the harness. In the door jamb, pull on the rubber boot to remove it from either the door or the jamb, pull wire from the jamb towards the door & unplug.

As far as the doorpanels go, I really only need the drivers side. The other 3 are just added weight. I have 95+ door panels for the rear already and the pass front I have 5 or 6 of them laying around.

How much do you want for the set of 4 door panels and how much do you want for the harness?

You can call me on my cell phone if you want... (856)294-7535

Thanks...
Joe

[69c10stepside]

Ok so the front harness is just the same as any other pw/pl harness, i can wing it for the back two doors then. I am going to send you a pm on the parts.

Thanks,

Frank

[69c10stepside]

I should have all requests, follow up pms sent, if not drop me message!

[ms. Attitude]

ok.thanks for checking.you have a PM from me.

[swbls12b]

Have not read the entire thread so forgive me if they are sold but, if not how much for both door panels with shipping to 67209?

[69c10stepside]

Sent pm to swbls12b.

[69c10stepside]

Almost last call on parts not spoken for, before they head to ebay.

[jeffspower]

My wallet is shrinking faster than anticipated- so don't hold onto the seats for me. I want them- but it could be a while. I will take the cruise unit if it works. Let me know & i'll get ya paid & where- to ship info. Thanks!

[69c10stepside]

Originally Posted by jeffspower

My wallet is shrinking faster than anticipated- so don't hold onto the seats for me. I want them- but it could be a while. I will take the cruise unit if it works. Let me know & i'll get ya paid & where- to ship info. Thanks!

Just the cruise works for me, i will pm payment info to you!

Frank

[69c10stepside]

Updated sold list:
Headlights/turnsignals/Mirrors
Cruise Control
Tow hooks/Glovebox Door
A/c Control

Sale pending:
Door Panels


Taking offers on:
40/60 Seat (driver side power)
Steering Column
Steering Wheel
Front Clip Sheetmetal
All other parts (excluding parts hard to ship unless other arrangements made)


If there is something that you can think of that you need part wise for this bodystyle, drop me a line, I might have it!

I do plan on going to the board swapmeet, keep that in mind!

Thanks,

Frank

[69c10stepside]

Taking offers on the seat, I will ship anywhere UPS/Fedex will ship to on your dime.

[69c10stepside]

Update: Column sold.

[Mickey_D]

Do you happen to have a pair of these center caps on it? I realize yours will say "GMC" on them instead of the bowtie, I don't care.



If so, how much for the pair and the plactics "lug nuts" shipped to 56754?

Also, how about the instrument cluster?

Also, how much for the cup holder panel shown in this pic? http://picasaweb.google.com/thefrank...14971304064946

[69c10stepside]

Hey Darrin,

No center caps on this guy, I couldnt tell you how many sets of steel wheels i have, but no lug nut covers or center caps The instrument cluster worked, it has 197XXX miles on it, no tach. Cup holder I would take 25 shipped for.

I can tell you that the cluster will not work in your '90 model with out some changes made to your harness.

Frank

[Mickey_D]

Yeah, I know. I've got the page from the other site that tells how to adapt the harness and DRAC to make it work. If I was to buy the instrument panel from you, what would you charge for the panel, connector, and the DRAC?

And yes, I'm interested in the cupholder panel. Might have to wait until next payday to gather the funds for both as this time around was land taxes time.

$5.21 left in the bank account.

[69c10stepside]

For the cluster DRAC and connector pigtail, i would charge 60+shipping.

Let me know if you want, i can hold them for however long you need me to.

Thanks,

Frank

[Mickey_D]

Man, I'm beginning to spend quite a bit on here. I now owe somebody for a hood, and you for the gauge panel and cup holder. I've got to get some money together and get you folks paid!!

And yes, I'm interested in the parts. I just cannot promise how soon I'll have the money. I've been trying to pay for the hood for over a month now.

[69c10stepside]

No problem, I don't care to hold on to them for you, just let me know when you are ready

Frank

[72C10chevy4x4]

if the burb has barn doors, I am in need of the 'stay' that keeps it open for the right (passenger) barn door. If you have it, give me a total to 19901-thank you.

[chris@bigjranch.com]

I'm wondering if there's enough left of your suburban to make it into a four door cab? like the shell and all the doors? or did you already sell the doors? and where in NW Arkansas are you? Thanks.

[Mickey_D]

69c10stepside, YGPM...

[ms. Attitude]

still have not gotten my parts i paid for or a refund of my money.even sent him a letter a 2 weeks ago asking for my money back.no PM,no email,no nothing.hope you guys had better luck.sorry to bad talk someone but hey,its been since the middle of may and no response after repeated PM's and a letter to him.

[c10crazy]

Originally Posted by ms. Attitude

still have not gotten my parts i paid for or a refund of my money.even sent him a letter a 2 weeks ago asking for my money back.no PM,no email,no nothing.hope you guys had better luck.sorry to bad talk someone but hey,its been since the middle of may and no response after repeated PM's and a letter to him.

You may want to PM Josh or Liz about this and see if they have his phone number. I see he hasn't been on the board in almost 2 months!.

[69sixpackbee]

How about the engine wiring harness uncut with the ECM connectors?

Thanx,
Bud