Need Opinions Leave Side Trim???with PIC - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Desert Rat** · 12-31-2001, 08:01 AM

My Blazer is going in to get painted Autumnwood Light Gold its from the 2000 Chevy line,Im debationg on if i should leave the side moldings(was gonna have them welded up)but new ones arent very expensive,no matter what it wont be 2 tone.entire body will be gold and the roof white.

[img]http://communities.msn.com/_Secure/0OAAAAMISEPgUorvbuN1ZA7Y0*fwvkmVlpC6D*X*aRTj3Fabnhwqa5Wo68vMp1Mf4y7KDsXUYjwksqBkv3u27Z3QAcAA6AC8A/79Blazer-#1.jpg[/img]

[This message has been edited by Desert Rat (edited 12-31-2001).]

bigblock73 · 12-31-2001, 12:42 PM

If you were going to keep the two tone on the sides then I would definately leave the trim on. If you are going to paint the truck gold and the top white, then I would ditch the trim. The trim would look out of place if it was just sitting there doing nothing. My .02

brad2 · 01-01-2002, 01:27 AM

I agree

gchemist · 01-02-2002, 01:11 PM

I agree too. Ditch the moldings. I did.

Less stuff to replace later.

------------------
Gerardo
1983 Custom Truck
TX Plates: "BAD BOW"
http://www.geocities.com/abetterchemist/

herauf · 01-02-2002, 09:44 PM

ditto...

no two tone, no trim.

ryan.

**Desert Rat** · 01-02-2002, 10:09 PM

Well its done now,even if i wanted to keep trim,Bodyman called today with his progress.Got all holes welded up,trying to convince me to lose the door handles,think ill keep them for now(since its a daily driver)got the new door,hood,and fender on,and the tailgate to open and close so he says with one finger.before it needed to be slammed,and kicked open.Tommorow the DA sander comes out!!!!

------------------
69 GMC SWB 402t400 daily beater,.
67 GMC SWB 468t400 Project Go Fast

79 Blazer 2wd 350t350(awaiting its heart transplant)

1962 BelAir SW Project-currently 454t350.

99 Nissan Frontier 4cyl,5spd,-hey it gets good gas mileage,and the AC is COLD and its reliable!!!!

Located In Casa Grande,AZ(48 miles South of Phoenix)
WANTED 62-64 409 Engine,79 Chevy Blazer or P/U Door Panels,Dash Pad,Blazer Tailgate window,71-72 Leaf Spring Rearends(need 2)any ratio
Vintage Aluminum BBC valve covers,Crossram intakes,Finned Aluminum oil pans,63-63 Impala AT tilt column.Buy Sell or trade.

74 camper special · 01-06-2002, 05:21 PM

Wish I could have got to you sooner.
Should have kept the trim. Oh well, to each his own.

stllookn · 01-06-2002, 08:21 PM

Rat, Wise choice, lose the moldings! I like the monochrome look. We are going to lose the cab moldings on my son's truck as soon as I perfect my welding skills. That color is going to be the same as your '62...right? Nice color!

12-31-2001, 12:42 PM	#2
bigblock73 yeller Join Date: Oct 2001 Location: Twin Cities Posts: 13,824	If you were going to keep the two tone on the sides then I would definately leave the trim on. If you are going to paint the truck gold and the top white, then I would ditch the trim. The trim would look out of place if it was just sitting there doing nothing. My .02 __________________ Jeff 73-87.com 73-87.com Facebook page 73-87 cab corner 6x9 speaker brackets for sale 67-72 cab corner speaker brackets for sale 47-54 cab corner speaker brackets for sale

01-01-2002, 01:27 AM	#3
brad2 Registered User Join Date: Feb 2001 Location: edmond, ok Posts: 1,056	I agree __________________ 74 swb 71 2wd Jimmy 82 2wd Blazer

01-02-2002, 01:11 PM	#4
gchemist BAD BOW-Silverado XST Join Date: May 2000 Location: Senior Member from Austin, TX Posts: 6,431	I agree too. Ditch the moldings. I did. Less stuff to replace later. ------------------ Gerardo 1983 Custom Truck TX Plates: "BAD BOW" http://www.geocities.com/abetterchemist/ __________________ Gerardo a.k.a. Mad Chemist Silverado XST videos

01-02-2002, 09:44 PM	#5
herauf Registered User Join Date: Feb 2001 Location: san jose, ca Posts: 209	ditto... no two tone, no trim. ryan. __________________ 1987 k5 4x4...FOR SALE!!! (email for details) will eventually be replaced by a 70-72 4x4 k5

01-06-2002, 05:21 PM	#7
74 camper special Registered User Join Date: Jan 2002 Location: Quinton, VA Posts: 1	Wish I could have got to you sooner. Should have kept the trim. Oh well, to each his own. __________________ 1974 Cheyenne-super/20 Camper Special. 454

12-31-2001, 08:01 AM	#1
Desert Rat Senior Member Join Date: Dec 1999 Location: Darrington, Washington Posts: 3,963	Need Opinions Leave Side Trim???with PIC My Blazer is going in to get painted Autumnwood Light Gold its from the 2000 Chevy line,Im debationg on if i should leave the side moldings(was gonna have them welded up)but new ones arent very expensive,no matter what it wont be 2 tone.entire body will be gold and the roof white. [img]http://communities.msn.com/_Secure/0OAAAAMISEPgUorvbuN1ZA7Y0fwvkmVlpC6DX*aRTj3Fabnhwqa5Wo68vMp1Mf4y7KDsXUYjwksqBkv3u27Z3QAcAA6AC8A/79Blazer-#1.jpg[/img] [This message has been edited by Desert Rat (edited 12-31-2001).]

01-02-2002, 10:09 PM	#6
Desert Rat Senior Member Join Date: Dec 1999 Location: Darrington, Washington Posts: 3,963	Well its done now,even if i wanted to keep trim,Bodyman called today with his progress.Got all holes welded up,trying to convince me to lose the door handles,think ill keep them for now(since its a daily driver)got the new door,hood,and fender on,and the tailgate to open and close so he says with one finger.before it needed to be slammed,and kicked open.Tommorow the DA sander comes out!!!! ------------------ 69 GMC SWB 402t400 daily beater,. 67 GMC SWB 468t400 Project Go Fast 79 Blazer 2wd 350t350(awaiting its heart transplant) 1962 BelAir SW Project-currently 454t350. 99 Nissan Frontier 4cyl,5spd,-hey it gets good gas mileage,and the AC is COLD and its reliable!!!! Located In Casa Grande,AZ(48 miles South of Phoenix) WANTED 62-64 409 Engine,79 Chevy Blazer or P/U Door Panels,Dash Pad,Blazer Tailgate window,71-72 Leaf Spring Rearends(need 2)any ratio Vintage Aluminum BBC valve covers,Crossram intakes,Finned Aluminum oil pans,63-63 Impala AT tilt column.Buy Sell or trade.

01-06-2002, 08:21 PM	#8
stllookn Saving 1 truck at a time! Join Date: Aug 2001 Location: Kent, WA Posts: 6,465	Rat, Wise choice, lose the moldings! I like the monochrome look. We are going to lose the cab moldings on my son's truck as soon as I perfect my welding skills. That color is going to be the same as your '62...right? Nice color! __________________ '68 C20 Longhorn 50th Anniversary 400/TH400 '68 C20 Longhorn 50th Anniversary 468/TH400w/buckets '72 C20 Halfhorn (Longhorn w/o cab and front clip) '69 Flxible Cruiser (look up ugly in the dictionary)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.