|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-22-2003, 01:47 AM
|
#1 |
|
Registered User
Join Date: Feb 2003
Location: Sacramento, CA
Posts: 53
|
Question about lowering blocks..
 Is it possible to use a set of lowering blocks in the rear, if it has coil springs?
__________________
68' Chevy truck longbed: flows, 4/6 drop, k&n filter, GMC front clip, and 20s |
|
|
|
02-22-2003, 02:53 AM
|
#2 |
|
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
yes ... all you need are the blocks and longer U-bolts.
|
|
|
|
|
02-22-2003, 04:47 AM
|
#3 |
|
What if?
Join Date: Oct 2002
Location: Choctaw,Oklahoma
Posts: 649
|
whats the max you can go on lowering blocks?
__________________
2002 red extended cab Silverado 2002 Wheatland yellow Suburban |
|
|
|
|
02-22-2003, 06:40 AM
|
#4 |
|
Registered User
Join Date: Feb 2003
Location: Sacramento, CA
Posts: 53
|
But were would you place the blocks? because I have seen trucks with leaf springs that have them and I know that it can't be installed the same way. I want to add a 1in lowering block to level my back with the front.
__________________
68' Chevy truck longbed: flows, 4/6 drop, k&n filter, GMC front clip, and 20s |
|
|
|
|
02-22-2003, 09:00 AM
|
#5 |
|
Registered User
Join Date: Dec 2002
Location: burlington KY
Posts: 175
|
if you have coils it goes between the rear axle and the trailing arm, (under neath the axle, and above the trailing arm) with longer U bolts
|
|
|
|
|
02-22-2003, 09:20 AM
|
#6 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
A 2" block is prettyclose to max if you are running 15" wheels.....much more, & you will be below "scrub lines". crazyL
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
02-23-2003, 11:55 PM
|
#7 |
|
4 speed, hurst shiftin
Join Date: Jun 2002
Location: Hudson, Wi
Posts: 405
|
put 3 inch drop blocks in .....drop in a 800hp motor, lighten up the front...and put gas shooting nozzles on the rear bumper , i think this will show using the scrub line to its full potential
__________________
Shane 1970 Chevy C10 |
|
|
|
|
02-24-2003, 01:44 PM
|
#8 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
LOL! Did you like those fire burnouts from the 60s?
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
