72 k10 4x4 front shaft - The 1947 - Present Chevrolet & GMC Truck Message Board Network

socal · 01-20-2009, 09:58 AM

will the front shaft of a 77 blazer fit my 72 k10? if not what shaft will fit in my th350/205 transfer case?

Mike C · 01-22-2009, 09:35 PM

Maybe. Probably not the answer you are looking for. You need to measure the two then you can make the decision.

Cyclone · 01-22-2009, 09:39 PM

Quote:

Originally Posted by socal

will the front shaft of a 77 blazer fit my 72 k10? if not what shaft will fit in my th350/205 transfer case?

I have a used 72 shaft , $65. plus shipping from NorCal.
Are you running any lift? How much?
What style output on your 205?

socal · 01-23-2009, 05:58 PM

It should be around 29 inches Name: Copy of DSCF0254.jpg
Views: 129
Size: 24.7 KB

socal · 01-23-2009, 08:24 PM

Here is the pic of the t/c side
Name: Copy of DSCF0257.jpg
Views: 141
Size: 93.9 KB

Cyclone · 01-23-2009, 08:37 PM

Are those holes in the yoke threaded?

socal · 01-23-2009, 08:50 PM

No they are no, Same as the axle side 2 threaded clamps with a 1/2 inch nut.

Cyclone · 01-23-2009, 09:07 PM

OK, the red one in my pic above will work then, I'll get a cost from UPS.

socal · 01-23-2009, 09:09 PM

thanks C, pm me when you do

01-20-2009, 09:58 AM	#1
socal Registered User Join Date: Jan 2009 Location: San Diego, CA Posts: 19	72 k10 4x4 front shaft will the front shaft of a 77 blazer fit my 72 k10? if not what shaft will fit in my th350/205 transfer case?

01-22-2009, 09:35 PM	#2
Mike C Registered User Join Date: Dec 1999 Location: Austin, TX, USA Posts: 7,728	Re: 72 k10 4x4 front shaft Maybe. Probably not the answer you are looking for. You need to measure the two then you can make the decision. __________________ 44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax

01-23-2009, 05:58 PM	#4
socal Registered User Join Date: Jan 2009 Location: San Diego, CA Posts: 19	Re: 72 k10 4x4 front shaft It should be around 29 inches

01-23-2009, 08:24 PM	#5
socal Registered User Join Date: Jan 2009 Location: San Diego, CA Posts: 19	Re: 72 k10 4x4 front shaft Here is the pic of the t/c side

01-23-2009, 08:37 PM	#6
Cyclone Registered User Join Date: Oct 2004 Location: Sonoma, CA Posts: 319	Re: 72 k10 4x4 front shaft Are those holes in the yoke threaded?

01-23-2009, 08:50 PM	#7
socal Registered User Join Date: Jan 2009 Location: San Diego, CA Posts: 19	Re: 72 k10 4x4 front shaft No they are no, Same as the axle side 2 threaded clamps with a 1/2 inch nut.

01-23-2009, 09:07 PM	#8
Cyclone Registered User Join Date: Oct 2004 Location: Sonoma, CA Posts: 319	Re: 72 k10 4x4 front shaft OK, the red one in my pic above will work then, I'll get a cost from UPS.

01-23-2009, 09:09 PM	#9
socal Registered User Join Date: Jan 2009 Location: San Diego, CA Posts: 19	Re: 72 k10 4x4 front shaft thanks C, pm me when you do



Register or Log In To remove these advertisements.