|
06-15-2009, 10:53 PM
|
#1 |
|
Registered User
Join Date: Mar 2007
Location: East Texas
Posts: 429
|
Lowering body mounts.
in reference to a '68 1/2 ton.
Unless I missed the thread,there hasnt been a cut & dried answer on lowering the body mounts. Ive heard(before)1" will put your rockers on the ground.Is that pinch weld or is that w/pinch removed? Im looking to get it as low as I can w/o touching pavement to body. I understand where the trimming will need to be done to cab and core support area,just need a reference point of drop to work off of. Thanks for any info. |
|
|
|
06-17-2009, 11:35 PM
|
#2 |
|
Happy to be here
 
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,021
|
Re: Lowering body mounts.
Anyone?
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" |
|
|
|
|
06-18-2009, 12:34 AM
|
#3 |
|
Senior Member
Join Date: Dec 2003
Location: Mesa,Az
Posts: 3,981
|
Re: Lowering body mounts.
Here's a link to a thread where we lowered the mounts 1".
I wouldn't go more than 3/4" if it were my own. http://www.67-72chevytrucks.com/vboa...d.php?t=234118
__________________
www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003! Last edited by PBFAB.COM; 06-18-2009 at 12:34 AM. |
|
|
|
|
06-18-2009, 11:28 AM
|
#4 | |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
|
Re: Lowering body mounts.
Quote:
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
|
06-18-2009, 03:57 PM
|
#5 |
|
Registered User
Join Date: Mar 2007
Location: East Texas
Posts: 429
|
Re: Lowering body mounts.
Hey Nathan,
Thanks for the reply. You and I talked about this a couple weeks ago. I remember what you said but the photos in the west coast thread arent clear as to how close the pinch is to the floor. The glare on the concrete and the angle of the pic makes it unclear. I was thinking 3/4" but wanted to make sure it would put me 1/4" from contacting the ground and not still have a 1/2" or more to go. If its a definite 1" difference(from bottom frame to pinch weld),then 3/4" is what Im looking for. |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
