the 8-9-09 what did you get done thread - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jdmaffeo · 08-10-2009, 02:34 PM

I haven't been around since the start of maybe February. I had totalled my daily driver and had to find a new one....This has put my project on the back burner since then. I have been storing it at my mom's about 2 hours away in East TX. Well I went out there this past weekend. She fired right up and I made a list of things that I must do before I bring her back to the big D! I had upgraded the charging system to a CS 144 (140 Amp) alternator because the 105 amp wasn't cutting it with the cooling fans, blower motor, and A/C. Well that only helped a little bit. I need to replace all the wiring from the alternator to benefit from the bigger alternator. Oh well... I really want to finish the one piece window project that I started in January with out much luck too, but I can do that here I hope! Here are a few pics!

Igotachevyor2 · 08-10-2009, 05:12 PM

i got the old flywheel cleened up and ready for the new clutch. got the driver power window motor installed (no more bungie cord for me

) started the gauge cluster swap. also picked up the rest of the fluids, plugs and filter needed for the motor install even have a shiny new electric fan that came home with me..

spankbomb · 08-10-2009, 08:52 PM

I pulled my doors off my cab. The cab is almost ready to come off the frame so I can give the frame the attention it needs.

08-10-2009, 02:34 PM	#26
jdmaffeo Registered User Join Date: Dec 2005 Location: Dallas, TX Posts: 241	Re: the 8-9-09 what did you get done thread I haven't been around since the start of maybe February. I had totalled my daily driver and had to find a new one....This has put my project on the back burner since then. I have been storing it at my mom's about 2 hours away in East TX. Well I went out there this past weekend. She fired right up and I made a list of things that I must do before I bring her back to the big D! I had upgraded the charging system to a CS 144 (140 Amp) alternator because the 105 amp wasn't cutting it with the cooling fans, blower motor, and A/C. Well that only helped a little bit. I need to replace all the wiring from the alternator to benefit from the bigger alternator. Oh well... I really want to finish the one piece window project that I started in January with out much luck too, but I can do that here I hope! Here are a few pics! Attached Images __________________ 1984 Chevy Stepside, 4spd granny, 4 1/2 front/6 inch rear drop.

08-10-2009, 05:12 PM	#27
Igotachevyor2 Apache Club Join Date: Jan 2006 Location: Goodlettsville,Tn. Posts: 1,294	Re: the 8-9-09 what did you get done thread i got the old flywheel cleened up and ready for the new clutch. got the driver power window motor installed (no more bungie cord for me ) started the gauge cluster swap. also picked up the rest of the fluids, plugs and filter needed for the motor install even have a shiny new electric fan that came home with me.. __________________ 58 CHEVY APACHE I 74 CHEVY C-10 I 78 K-10 donor truck I 89 SONOMA My Trucks Apache Sitting Idle MySpace Project Dad's Truck (74 C-10 to K-10 conversion) .

08-10-2009, 08:52 PM	#28
spankbomb Registered User Join Date: May 2009 Location: Elgin, TX Posts: 140	Re: the 8-9-09 what did you get done thread I pulled my doors off my cab. The cab is almost ready to come off the frame so I can give the frame the attention it needs.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.