Register or Log In To remove these advertisements. |
|
|
View Poll Results: Is there an interest in the product? | |||
YES | 4 | 25.00% | |
NO | 12 | 75.00% | |
Voters: 16. You may not vote on this poll |
|
Thread Tools | Display Modes |
11-05-2009, 08:04 PM | #1 |
Life, Be In It.....
Join Date: Oct 2003
Location: Novato, California
Posts: 1,498
|
Who's interested????????????????
A fellow member (Shane) and I are doing research to see if there is an interest in a suspension part, before we have if made.
We’re going to have a machinist cut large washer/spacers out of stainless steel for the rear trailing arms with air bags. Similar to what you see pictured below. They would be .250 thick - 2.750 outer diameter with a 13/32 inner diameter hole (clearance for a 3/8" bolt). Unfortunately the cost for a set (that’s two washers) would be $50.00 shipped within the US. I know that is expensive and there are other alternatives, but this will be a unique quality piece. In order of us to get that price we need to have a minimum order of 20 pieces or 10 sets. OR IF SOMEONE HAS A CONNECTION THAT CAN MAKE THE ITEM WITH THE SAME MATERIAL FOR A CHEAPER PRICE, DROP US A PM. THANKS Anyone Interested?
__________________
Project Name: LEMON DROP. Reconstruction started "December 2000". Projected completion date "Who knows" http://67-72chevytrucks.com/vboard/s...d.php?t=200082 Last edited by jugernot; 11-05-2009 at 11:04 PM. |
11-05-2009, 08:16 PM | #2 |
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Who's interested????????????????
Just for clarity sake, we are not making ANYTHING on these at this price. These are being sold AT COST.
|
11-05-2009, 08:40 PM | #3 |
Senior Member
Join Date: Dec 2003
Location: Mesa,Az
Posts: 3,981
|
Re: Who's interested????????????????
It's a product I would happily help you sell. I think they are a NO brainer.
__________________
www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003! |
11-05-2009, 08:42 PM | #4 |
low n' slo
Join Date: Mar 2009
Location: rosenberg, texas
Posts: 5,175
|
Re: Who's interested????????????????
i was wondering what the hell you guys used as a washer in that pic...lol. i never knew it was stainless steel, looks nice.
__________________
67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____|__|__\__ ,.,,,.,.,,.,|_O _______ O_] |
11-05-2009, 09:30 PM | #5 |
Happy to be here
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,021
|
Re: Who's interested????????????????
Clearly a cool piece, but will they sell for 50 bucks? You should have made this a poll.
Would you buy this product at this price yes/no.
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" |
11-05-2009, 10:06 PM | #6 |
67-72 parts collector,…
Join Date: Nov 2002
Location: Mid-MO
Posts: 22,700
|
Re: Who's interested????????????????
Would it be cheaper to get somone to cut them out on a waterjet?
__________________
Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823 |
11-05-2009, 10:22 PM | #7 |
Registered User
Join Date: Apr 2009
Location: Bend,Oregon
Posts: 225
|
Re: Who's interested????????????????
why are they so expensive ?
|
11-05-2009, 10:48 PM | #8 |
Life, Be In It.....
Join Date: Oct 2003
Location: Novato, California
Posts: 1,498
|
Re: Who's interested????????????????
The one pictures I believe is made from aluminum. I used the picture purely for reference, so everyone would have a visual idea of what we want to make.
__________________
Project Name: LEMON DROP. Reconstruction started "December 2000". Projected completion date "Who knows" http://67-72chevytrucks.com/vboard/s...d.php?t=200082 |
11-05-2009, 10:51 PM | #9 |
Life, Be In It.....
Join Date: Oct 2003
Location: Novato, California
Posts: 1,498
|
Re: Who's interested????????????????
The machinist explained that they will be expensive due to the high price of 304 Stainless Steel right now. The majority of the cost is in the material and hardly any in labor.
__________________
Project Name: LEMON DROP. Reconstruction started "December 2000". Projected completion date "Who knows" http://67-72chevytrucks.com/vboard/s...d.php?t=200082 |
11-05-2009, 10:57 PM | #10 | |
Life, Be In It.....
Join Date: Oct 2003
Location: Novato, California
Posts: 1,498
|
Re: Who's interested????????????????
Quote:
Thanks, its always nice to get the Porter Built seal of approval.
__________________
Project Name: LEMON DROP. Reconstruction started "December 2000". Projected completion date "Who knows" http://67-72chevytrucks.com/vboard/s...d.php?t=200082 |
|
11-05-2009, 11:14 PM | #11 |
Senior Member
Join Date: May 2004
Location: johnstown, NY
Posts: 2,393
|
Re: Who's interested????????????????
Could they be CNC cut? I could get a price if so.
|
11-05-2009, 11:32 PM | #12 |
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Who's interested????????????????
The quoted price is CNC cut.
I'm currently looking for lower cost provider for material, may even look at a different grade of stainless that may also allow for a lower price. I'll keep everyone informed. Last edited by Shane; 11-05-2009 at 11:37 PM. |
11-05-2009, 11:38 PM | #13 |
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Who's interested????????????????
You could have them cut on a water jet, but you would not get the finish that turning them on a lathe provides. It wouldn't be any cheaper either, as most guys are charging anywhere from $75-$125 per hour for water jet work. Whereas CNC turning work is going for less than $50 per hour in most parts of the country.
|
11-05-2009, 11:39 PM | #14 |
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Who's interested????????????????
|
11-05-2009, 11:42 PM | #15 |
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: Who's interested????????????????
Do not take this wrong, I am asking a question from my ignorant hillbilly perspective. I've never run bags on my junk, just lots of lowered spring sets. I just run a big grade 8 washer and be done with it.
Why the focus on using the (apparently expensive) grade of stainless ? Why is this better than a big steel washer that costs a few cents ? Is it simply appearance and corrosion resistance or is there some other advantage I don't see ?
__________________
I'm on the Instagram- @Gearhead_Kevin Last edited by Tx Firefighter; 11-05-2009 at 11:43 PM. |
11-05-2009, 11:55 PM | #16 |
Senior Member
Join Date: Aug 2005
Location: tulsa OK
Posts: 3,070
|
Re: Who's interested????????????????
wayyyy to expensive for 2 washers...i think if you could get them for 20$ or less shipped, then they'ld sell
Last edited by 68 short step; 11-05-2009 at 11:56 PM. |
11-05-2009, 11:59 PM | #17 |
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Who's interested????????????????
Appearance and corrosion resistance are the only real advantages, honestly.
|
11-06-2009, 12:03 AM | #18 | |
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Who's interested????????????????
Quote:
The kicker is the price breaks that come with larger quantities, but when you make them in batches of less than 100 at a time then it is very difficult to get to the lower price. I'm working on it guys. I promise. Last edited by Shane; 11-06-2009 at 12:03 AM. |
|
11-06-2009, 12:20 AM | #19 |
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: Who's interested????????????????
They are not as thick, but they are 316 stainless steel, 13/32 id hole, 2 inch od. About a buck each...
http://www.mcmaster.com/#91525a143/=4dntsa
__________________
I'm on the Instagram- @Gearhead_Kevin Last edited by Tx Firefighter; 11-06-2009 at 12:24 AM. |
11-06-2009, 12:21 AM | #20 |
Happy to be here
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,021
|
Re: Who's interested????????????????
Is stainless really necessary? Couldn't you make them from steel?
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" |
11-06-2009, 05:08 AM | #21 |
Registered User
Join Date: Oct 2008
Location: oxnard ca
Posts: 2,201
|
Re: Who's interested????????????????
WE CAN MAKE THESE FOR YOU GUYS
AND ALSO GIVE YOU A BETTER PRICE.We have our own cnc mills and lathes and a water jet cutter if interested e-mail justin@scottshotrods.com |
11-06-2009, 08:02 AM | #22 | |
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Who's interested????????????????
Quote:
Thus the reason for the SS. |
|
11-06-2009, 08:05 AM | #23 | |
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Who's interested????????????????
Quote:
Same dimensions as above but add a .125 radius on ONE O.D. corner ... make from 2 5/8" 304 stainless round bar. Let us know. Last edited by Shane; 11-06-2009 at 09:06 AM. |
|
11-06-2009, 08:11 AM | #24 | |
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Who's interested????????????????
Quote:
Anyone who doesn't want a set, no problem and no hurt feelings. Jugernot asked me to look into it so I did and the guy doing the machining quoted me this price to do 20 parts. At this point we are only trying to find buyers for the other 7-8 sets. |
|
Bookmarks |
|
|