The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-08-2003, 08:06 PM   #1
pphatbasstard
Registered User
 
pphatbasstard's Avatar
 
Join Date: Oct 2002
Posts: 166
dropping my truck

I am planning on droping my 67 buy cutting the springs, I know this is not the best way but i am on a budget it and this is just for now. My question is how do i know how much to cut? i want about a 4" drop so how much spring should i cut? thanks
pphatbasstard is offline   Reply With Quote
Old 05-08-2003, 09:15 PM   #2
pissonNOS
senior member
 
pissonNOS's Avatar
 
Join Date: Feb 2003
Location: fort macleod alberta
Posts: 2,770
1 full coil
i would also recomend getting a wheel alignment when ur done even tho they will have to shim the hell out of things
__________________
69 GMC bagged
pissonNOS is offline   Reply With Quote
Old 05-10-2003, 01:04 AM   #3
pphatbasstard
Registered User
 
pphatbasstard's Avatar
 
Join Date: Oct 2002
Posts: 166
1 full coil will make for 4 inches? and what do u mean by shim the hell out of it?

thanks
pphatbasstard is offline   Reply With Quote
Old 05-10-2003, 11:23 PM   #4
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
Start w/1 coil & then cut 1/2 a coil @ a time after that to get what you want. You will have to use extra shims for the upper a-arms in order to achieve proper (or close to proper) alignment.

Some advice. . .... once you trim 2 coils off the front springs, the coils can easily come out of the spring pocket if the suspension becomes unloaded (like if you were to hit a big dip in the road & the truck rises rapidly). I've been in a buddies truck when this happened & it was a very scary moment. You'll also have a hard time getting someone to align the front w/only cut coils for the drop. With some drop spindles & 1 coil off you'll get 5" drop, a decent ride & still be fairly easy to align. Good luck.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Old 05-11-2003, 12:14 AM   #5
70 Jimmy
aka Crusher, Crushergmc
 
70 Jimmy's Avatar
 
Join Date: Mar 2000
Location: Oregon
Posts: 1,834
I've heard not to cut more than 1 coil or you'll have some bumpsteer. I cut 1 but haven't driven it yet. Good luck.
__________________
"KEEP IT DOWN!"
70 Jimmy 454 2wd
56 GMC Big Window
"It's funny till someone gets hurt, then it's freakin' hilarious"
70 Jimmy is offline   Reply With Quote
Old 05-11-2003, 02:57 AM   #6
pphatbasstard
Registered User
 
pphatbasstard's Avatar
 
Join Date: Oct 2002
Posts: 166
thanks guys. but what is bumpsteer?
pphatbasstard is offline   Reply With Quote
Old 05-11-2003, 02:18 PM   #7
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
That's when severe angle of the tierods causes the steering to pull whenever going over bumps in the road.

Cut coils don't accomodate for this & that's the reason for 'bumpsteer'. Drop spindles have the steering arm modified to compensate & allow the tierods to parallel the a-arms (which should be level to the ground).
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Old 05-11-2003, 05:56 PM   #8
Brad
Out of the carpool lane.
 
Brad's Avatar
 
Join Date: Jan 2000
Location: Clark Co, WA
Posts: 5,672
You should be fine with exactly 1 coil cut or less. Use a grinder with a cutoff wheel or similar when cutting, as a torch would change the temper of the steel. Be aware that you can't cut rear springs due to the pigtails on both ends. I've even lowered mine using the torch to heat the springs and I was just fine. Mine were 31 year old springs at the time. But, this isn't recommended - only a short term solution until you can afford drop springs and spindles.
__________________

1968 C-10 SWB, 5.7 Vortec/700R4/3.73 posi, Torch Red
1968 Camaro, 250/Powerglide, all original (No, I'm not gonna drop a 350 in it!...Jeez!)
2000 Honda VFR in the faster yellow!
2008 Husqvarna TE-610

1967 C-10 SWB 'Six Appeal'-Gone but not forgotten...

Brad is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:19 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com