How to wire a 700r4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

HSkinner · 10-02-2010, 11:28 PM

I've got the 700r4 installed and I keep seeing stuff about locking up the torque convertor. Do I have to do this to get the truck to function properly. I don't care much about locking up 4th gear, I just want it to shift right.

**Captainfab** · 10-03-2010, 01:25 AM

There are many threads on proper 700R4 setup and lockup converter wiring over in the 'Engine and Drivetrain' section. The correct adjustment of the TV cable is critical to the life of the trans. If it is not setup properly, you will burn up your trans in a short time. IIRC engaging the lockup mode in the trans also applies full pressure on the OD clutches. Which is a good thing to have.

72timemachine · 10-03-2010, 01:48 AM

I put a 700r4 in my 72 c-10 and I love it. In order for your trans to truely lock up in 4th gear and get that better mileage you have these two options down below.

The first one is more expensive and causes the converter to disengage upon braking, whereas the 2nd one will also lock your converter in 4th gear but does not disengage the converter on braking but this one never gave me any trouble so far, beside the trans returns to a lower gear anyway when you slow, stop, or deck the throttle.

The choice is yours either way you have to drop the pan, do yourself a favor, add a drain plug and have it welded (the nut the drain plug threads into) on from the inside. Change the trans fluid 30,000 miles or less and when you take off the filter be sure the small o ring gasket is not still stuck up inside the trans, use a small hooked tool to pull it out evenly a little at a time until it come out.

Good luck.

http://www.speedwaymotors.com/700R4-...-Kit,2362.html

http://cgi.ebay.com/ebaymotors/LOCK-...7#ht_777wt_877

Woogeroo · 10-03-2010, 02:20 AM

700r4 articles, info. pertaining to our trucks - a text file with urls, links

transmission links

Also look for the FAQ / Truck tech forum on this site we are on.

-W

**LEEVON** · 10-03-2010, 07:03 AM

The wiring controls the lock-up solenoid. It's really simple, I have a post here somewhere describing what pin to use on the connector. Chances are your trans already has the internal stuff.

Now, just to be clear you don't HAVE to use the lock-up but it will drop your RPM's and lower temps. I only use it on the freeway at 70 plus.

Lock-up and TV cable are two very different things. If you want to make your trans last you need to invest in the proper linkages, a pressure gauge and read up on how it all works. Otherwise you'll fry it in a heartbeat.

karlbenz · 10-10-2010, 08:29 PM

got mine on a toggle switch

raycow · 10-11-2010, 03:58 AM

Unless your transmission is defective or has been modified by a PO, you absolutely do not have to go inside it to enable the lockup function. All of the necessary components were installed by GM and wired to the connector on the driver side of the transmission. Remember, the lockup worked on every one of these transmissions when it left the factory.

The aftermarket vendors have done a good job of making the lockup appear much more difficult than it really is just so they could sell you overpriced parts that you don't need.

Ray

10-02-2010, 11:28 PM	#1
HSkinner Registered User Join Date: Jul 2010 Location: Snowflake Az. Posts: 86	How to wire a 700r4 I've got the 700r4 installed and I keep seeing stuff about locking up the torque convertor. Do I have to do this to get the truck to function properly. I don't care much about locking up 4th gear, I just want it to shift right.

10-03-2010, 01:25 AM	#2
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: How to wire a 700r4 There are many threads on proper 700R4 setup and lockup converter wiring over in the 'Engine and Drivetrain' section. The correct adjustment of the TV cable is critical to the life of the trans. If it is not setup properly, you will burn up your trans in a short time. IIRC engaging the lockup mode in the trans also applies full pressure on the OD clutches. Which is a good thing to have. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

10-03-2010, 01:48 AM	#3
72timemachine Registered User Join Date: Oct 2008 Location: los angeles ca Posts: 220	Re: How to wire a 700r4 I put a 700r4 in my 72 c-10 and I love it. In order for your trans to truely lock up in 4th gear and get that better mileage you have these two options down below. The first one is more expensive and causes the converter to disengage upon braking, whereas the 2nd one will also lock your converter in 4th gear but does not disengage the converter on braking but this one never gave me any trouble so far, beside the trans returns to a lower gear anyway when you slow, stop, or deck the throttle. The choice is yours either way you have to drop the pan, do yourself a favor, add a drain plug and have it welded (the nut the drain plug threads into) on from the inside. Change the trans fluid 30,000 miles or less and when you take off the filter be sure the small o ring gasket is not still stuck up inside the trans, use a small hooked tool to pull it out evenly a little at a time until it come out. Good luck. http://www.speedwaymotors.com/700R4-...-Kit,2362.html http://cgi.ebay.com/ebaymotors/LOCK-...7#ht_777wt_877

10-03-2010, 02:20 AM	#4
Woogeroo Registered User Join Date: Aug 2003 Location: tool box Posts: 3,115	Re: How to wire a 700r4 700r4 articles, info. pertaining to our trucks - a text file with urls, links transmission links Also look for the FAQ / Truck tech forum on this site we are on. -W

10-03-2010, 07:03 AM	#5
LEEVON Moderator Join Date: Jul 2006 Location: Ozark, MO Posts: 4,888	Re: How to wire a 700r4 The wiring controls the lock-up solenoid. It's really simple, I have a post here somewhere describing what pin to use on the connector. Chances are your trans already has the internal stuff. Now, just to be clear you don't HAVE to use the lock-up but it will drop your RPM's and lower temps. I only use it on the freeway at 70 plus. Lock-up and TV cable are two very different things. If you want to make your trans last you need to invest in the proper linkages, a pressure gauge and read up on how it all works. Otherwise you'll fry it in a heartbeat. __________________ '20 Silverado Trail Boss ~ '17 Tahoe ~ '79 K15 Sierra Grande ~ '76 Blazer 2wd ~ '71 Cheyenne swb ~ '55 Pontiac Safari ~'50 3100 bagged ~ '80 Wife ~ Late model kids

10-10-2010, 08:29 PM	#6
karlbenz Registered User Join Date: Nov 2008 Location: kannapolis, nc Posts: 528	Re: How to wire a 700r4 got mine on a toggle switch

10-11-2010, 03:58 AM	#7
raycow Registered User Join Date: Mar 2003 Location: San Francisco, CA USA Posts: 2,454	Re: How to wire a 700r4 Unless your transmission is defective or has been modified by a PO, you absolutely do not have to go inside it to enable the lockup function. All of the necessary components were installed by GM and wired to the connector on the driver side of the transmission. Remember, the lockup worked on every one of these transmissions when it left the factory. The aftermarket vendors have done a good job of making the lockup appear much more difficult than it really is just so they could sell you overpriced parts that you don't need. Ray



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.