Window Channel for a '50 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Groyd · 10-21-2010, 11:13 PM

I've been looking forever to find all the pieces I need to put windows into a stripped down door. I found this and was wondering if anyone knew where to find part 16.190? I've tried all the usual places and they say they don't carry it.
I know this is a pic of a 51-53, but it is the only pic I could find that showed the part.

Atomsplitter · 10-21-2010, 11:38 PM

oops, double post, sorry

Atomsplitter · 10-21-2010, 11:39 PM

It`s hard to see from that picture but is it the channel that holds the rubber wiper/seal or it at the base of the window glass?

Groyd · 10-27-2010, 05:20 PM

Quote:

Originally Posted by Atomsplitter

It`s hard to see from that picture but is it the channel that holds the rubber wiper/seal or it at the base of the window glass?

I'm not sure if it just holds the glass or if there is a rubber piece that goes inside it.

Here is a picture of the piece.

Here is a pic of where it would be located on the door (only on the inside of course). There are two screws at the bottom that hold it to the door.

Sorry it took so long to respond, I've been out of town.

Thanks again.

FiftyTwo · 10-27-2010, 09:03 PM

That is the Glass Guide.
47-50 trucks have a Left and Right. The window felt channel goes inside the glass guide, then up and around the inside top of the door, and then back down the other guide. The glass rides up and down in the felt channel.

http://www.truckandcarshop.com/trucks47_59/t47_055.html

Groyd · 10-27-2010, 10:58 PM

Quote:

Originally Posted by FiftyTwo

That is the Glass Guide.
47-50 trucks have a Left and Right. The window felt channel goes inside the glass guide, then up and around the inside top of the door, and then back down the other guide. The glass rides up and down in the felt channel.

http://www.truckandcarshop.com/trucks47_59/t47_055.html

Thank you so much, I've been looking everywhere for one and couldn't find anyone who sold them.

-MG

Groyd · 10-28-2010, 05:19 PM

They don't have them either. I guess whoever makes them has quit production or is just getting started. The lady I talked to wasn't sure.

FiftyTwo · 10-28-2010, 07:57 PM

Here's two more places that show they sell them. It also appears that some places are putting them into a kit with the window channel felt.

SEE PAGE 31: $20.00 each
http://www.billstruckshop.com/Catalo...2%20Master.pdf

Shows a kit for $139.95
http://www.aaaparts.cwmax.com/chevydor.htm

Groyd · 10-28-2010, 09:55 PM

Quote:

Originally Posted by FiftyTwo

Here's two more places that show they sell them. It also appears that some places are putting them into a kit with the window channel felt.

SEE PAGE 31: $20.00 each
http://www.billstruckshop.com/Catalo...2%20Master.pdf

Shows a kit for $139.95
http://www.aaaparts.cwmax.com/chevydor.htm

I spent two hours today looking for anything, and you've got two more. I don't know how you did it, but thanks again.

-MG

FiftyTwo · 10-28-2010, 10:27 PM

I spend way too much time on the computer...here is another for you. No picture but sounds like what you want.

http://www.chevsofthe40s.com/detail/..._W_SCREWS.html

weldvair@embarqmail. · 10-29-2010, 07:58 AM

I had mine made at a sheet metal shop for $10/ea.

Don

Atomsplitter · 10-29-2010, 08:54 PM

If thats the Bills Truck Stop in Courtice, Ontario, Canada he's located 10 minutes from me.
Let me know if I can help!

Groyd · 10-30-2010, 10:56 AM

Quote:

Originally Posted by Atomsplitter

If thats the Bills Truck Stop in Courtice, Ontario, Canada he's located 10 minutes from me.
Let me know if I can help!

Thanks, I might take you up on that offer.

-MG

Dan Bowles · 10-30-2010, 09:07 PM

I've been saving these kinds of things out of junk doors. The last set of doors I bought was missing one and one was rotted out. Amazing since the doors weren't that bad.

BIG CHEVY 3600 · 11-07-2010, 08:19 PM

Did you try LMC?

Groyd · 11-08-2010, 05:51 PM

Quote:

Originally Posted by BIG CHEVY 3600

Did you try LMC?

No go at LMC. I ordered a kit from Brothers that may include it. Not sure yet.

glowins10 · 11-14-2010, 07:45 PM

Groyd, can you let me know if this (brothers) kit includes the glass guide channel you need, i need one too! I am planning on making one, but if this kit includes it i might just pay a little extra and get everything i need at once.

Groyd · 11-15-2010, 11:52 AM

Quote:

Originally Posted by glowins10

Groyd, can you let me know if this (brothers) kit includes the glass guide channel you need, i need one too! I am planning on making one, but if this kit includes it i might just pay a little extra and get everything i need at once.

I called yesterday and they were about to ship it. . . finally. I'll tell you once it gets in.

10-21-2010, 11:13 PM	#1
Groyd Registered User Join Date: Apr 2009 Location: Edmond, OK Posts: 393	Window Channel for a '50 I've been looking forever to find all the pieces I need to put windows into a stripped down door. I found this and was wondering if anyone knew where to find part 16.190? I've tried all the usual places and they say they don't carry it. I know this is a pic of a 51-53, but it is the only pic I could find that showed the part. __________________ 1951 Chevy 3100/S-10: http://67-72chevytrucks.com/vboard/s...d.php?t=406072 1957 Chevy 3200 1971 2WD Blazer - Sold

10-21-2010, 11:38 PM	#2
Atomsplitter Registered User Join Date: Mar 2006 Location: Ontario Posts: 514	Re: Window Channel for a '50 oops, double post, sorry Last edited by Atomsplitter; 10-21-2010 at 11:40 PM.

10-21-2010, 11:39 PM	#3
Atomsplitter Registered User Join Date: Mar 2006 Location: Ontario Posts: 514	Re: Window Channel for a '50 It`s hard to see from that picture but is it the channel that holds the rubber wiper/seal or it at the base of the window glass?

10-27-2010, 09:03 PM	#5
FiftyTwo Registered User Join Date: Mar 2009 Location: Apple Valley, MN Posts: 109	Re: Window Channel for a '50 That is the Glass Guide. 47-50 trucks have a Left and Right. The window felt channel goes inside the glass guide, then up and around the inside top of the door, and then back down the other guide. The glass rides up and down in the felt channel. http://www.truckandcarshop.com/trucks47_59/t47_055.html Last edited by FiftyTwo; 10-27-2010 at 10:08 PM. Reason: Added more info

10-28-2010, 05:19 PM	#7
Groyd Registered User Join Date: Apr 2009 Location: Edmond, OK Posts: 393	Re: Window Channel for a '50 They don't have them either. I guess whoever makes them has quit production or is just getting started. The lady I talked to wasn't sure. __________________ 1951 Chevy 3100/S-10: http://67-72chevytrucks.com/vboard/s...d.php?t=406072 1957 Chevy 3200 1971 2WD Blazer - Sold

10-28-2010, 07:57 PM	#8
FiftyTwo Registered User Join Date: Mar 2009 Location: Apple Valley, MN Posts: 109	Re: Window Channel for a '50 Here's two more places that show they sell them. It also appears that some places are putting them into a kit with the window channel felt. SEE PAGE 31: $20.00 each http://www.billstruckshop.com/Catalo...2%20Master.pdf Shows a kit for $139.95 http://www.aaaparts.cwmax.com/chevydor.htm Last edited by FiftyTwo; 10-28-2010 at 08:06 PM. Reason: bad link

10-28-2010, 10:27 PM	#10
FiftyTwo Registered User Join Date: Mar 2009 Location: Apple Valley, MN Posts: 109	Re: Window Channel for a '50 I spend way too much time on the computer...here is another for you. No picture but sounds like what you want. http://www.chevsofthe40s.com/detail/..._W_SCREWS.html

10-29-2010, 07:58 AM	#11
weldvair@embarqmail. Registered User Join Date: Feb 2008 Location: st cloud, fl Posts: 266	Re: Window Channel for a '50 I had mine made at a sheet metal shop for $10/ea. Don

10-29-2010, 08:54 PM	#12
Atomsplitter Registered User Join Date: Mar 2006 Location: Ontario Posts: 514	Re: Window Channel for a '50 If thats the Bills Truck Stop in Courtice, Ontario, Canada he's located 10 minutes from me. Let me know if I can help!

10-30-2010, 09:07 PM	#14
Dan Bowles AD Addict Join Date: Oct 2009 Location: Blissfield, MI Posts: 822	Re: Window Channel for a '50 I've been saving these kinds of things out of junk doors. The last set of doors I bought was missing one and one was rotted out. Amazing since the doors weren't that bad. Last edited by Dan Bowles; 10-30-2010 at 09:08 PM.

11-07-2010, 08:19 PM	#15
BIG CHEVY 3600 BIG CHEVY 3600 LONGBOX Join Date: Feb 2008 Location: Dallas, Texas Posts: 382	Re: Window Channel for a '50 Did you try LMC? __________________ If I were given 8 hours to chop down a large tree, I would spend the first 6 hours sharpening my ax. Abraham Lincoln http://s729.photobucket.com/albums/w...cpZZ3QQtppZZ20

11-14-2010, 07:45 PM	#17
glowins10 Registered User Join Date: Mar 2009 Location: Newton, IL Posts: 38	Re: Window Channel for a '50 Groyd, can you let me know if this (brothers) kit includes the glass guide channel you need, i need one too! I am planning on making one, but if this kit includes it i might just pay a little extra and get everything i need at once.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.