|
11-16-2010, 06:26 PM
|
#1 |
|
Broken Down
Join Date: Dec 2006
Location: Choctaw, Oklahoma
Posts: 1,267
|
Left Door Vent Window
Well I done did it!! I opened my little triagle vent window on my drivers door and the bottom stud/pivot broke so now it's just flapping by the outside hinge. How hard are these darn things to replace. I looked on LMC and they are a pretty penny $349.95 OUTRAGIOUS!!!! Any ideas to my delima?
__________________
kenm78 1982 Chevy 4X4 Project truck  “It’s better to keep your mouth shut and let people wonder about your ignorance, than open your mouth and reveal all doubt” |
|
|
|
11-16-2010, 08:30 PM
|
#2 | |
|
Senior Member
 Join Date: Feb 2010
Location: Maumelle, AR
Posts: 478
|
Re: Left Door Vent Window
Quote:
|
|
|
|
|
|
11-16-2010, 09:49 PM
|
#3 |
|
78K & 79C Jimmys
Join Date: Nov 2009
Location: Ottawa Ont CANADA
Posts: 7,901
|
Re: Left Door Vent Window
and they fit a wide year range,i just put 89 suburban vents into my 78 jimmy,and the later years have locks on them
__________________
John 1978 GMCJimmy4X4-350/203 1979 GMCJimmy4X2-305/350 |
|
|
|
|
11-16-2010, 11:59 PM
|
#4 |
|
Broken Down
Join Date: Dec 2006
Location: Choctaw, Oklahoma
Posts: 1,267
|
Re: Left Door Vent Window
They look like a PINA to swap out. What needs to be done to change them.
__________________
kenm78 1982 Chevy 4X4 Project truck “It’s better to keep your mouth shut and let people wonder about your ignorance, than open your mouth and reveal all doubt” |
|
|
|
|
11-17-2010, 12:15 AM
|
#5 |
|
78K & 79C Jimmys
Join Date: Nov 2009
Location: Ottawa Ont CANADA
Posts: 7,901
|
Re: Left Door Vent Window
for me the hardest part was the screws in the door frames(rusty).had to tap them with a hammer while turning them(seen with door open) yellow dots on door frame
and one screw on top of door-up red arrow window crank clip 4 screws across the bottom- yellow dots 2 screws in handle area- yellow dots 1 screw side edge-yellow dot red dots are bolts to remove under panel and there will be a small crew (to remove)holding the inside to the outside just under the vent window......jimmy and wiggle it out
__________________
John 1978 GMCJimmy4X4-350/203 1979 GMCJimmy4X2-305/350 Last edited by motornut; 11-17-2010 at 12:18 AM. |
|
|
|
|
11-17-2010, 12:49 PM
|
#6 |
|
Registered User
Join Date: Sep 2009
Location: Mpls, MN USA
Posts: 151
|
Re: Left Door Vent Window
And the front channel for the door glass is integral with the vent window assembly, so you'll be removing and replacing the operable window glass as well. Unless there's some way to leave it connected to the mechanism, and simply line the vent window and track, with the door glass? Haven't had to do this yet, but have the vent window assembly and a bare door sitting on my workbench, awaiting some time to work on it.
Pretty sure that the 'hinge' point of the vent window, is integral with the frame. I too was shocked by the price in the LMC and various catalogs, and scored a used vent window assembly from the salvage yard. Seemed like the easiest way to solve the problem, but it has turned intoa pretty involved repair. Good luck with yours!
__________________
TomS. '98 S-10 Blazer 4dr 4wd - 4.3, AT, stock & '85 K-10 w/ 305, 700r4, np208, and RUST! SOLD Dec 2014 |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
