1969 Blazer seats install - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Gary 70 Jimmy** · 01-01-2011, 09:22 PM

Took out the utillity bucket seats went to install my custom bucket seats and found out that the utility bucket seat tracks are longer had to drill new holes for the custom bucket seats. Then I looked under my 70 jimmy and it came with both sets of holes.

71jimmy · 01-02-2011, 03:19 PM

My '71 has two sets of holes also. Don't know why or when they did this. I've been comparing to the builds on this site as they come along, and it seems that some have them and some don't.

PS, the calendar is looking good in my man cave

**Gary 70 Jimmy** · 01-02-2011, 03:40 PM

Maybe they all came with the utility seat holes when the custom seats were order they add the hole for them.

**jaros44sr** · 01-02-2011, 04:09 PM

My '72 didn't have both sets, dunno...

pound41 · 01-02-2011, 10:13 PM

I think utility will match up with a bench seat in a pickup. I am welding in most of a pickup floor pan from a pickup from az in my blazer and it had the hole for my custom buckets just not the nut the other side has the nut. So I am sure they made them all for benches and then adjusted for the cst's

01-01-2011, 09:22 PM	#1
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,401	1969 Blazer seats install Took out the utillity bucket seats went to install my custom bucket seats and found out that the utility bucket seat tracks are longer had to drill new holes for the custom bucket seats. Then I looked under my 70 jimmy and it came with both sets of holes. __________________ 1972 GMC Jimmy 1/2 4X4 4wheel camper 1970 GMC Jimmy 1/2 4X4 350 1969 Chevy Blazer 1/2 4X4 307 1967 chevy LWB 3/4 396

01-02-2011, 03:19 PM	#2
71jimmy Registered User Join Date: Mar 2004 Location: Sacramento, CA Posts: 1,083	Re: 1969 Blazer seats install My '71 has two sets of holes also. Don't know why or when they did this. I've been comparing to the builds on this site as they come along, and it seems that some have them and some don't. PS, the calendar is looking good in my man cave __________________ '71 Jimmy, 350, SM465, NP205, 2in Tuff Country lift, 33s on rallies, TBI, softtop and hardtop "If life was fair you'd be able to afford one of each and a garage large enough to house them all."

01-02-2011, 03:40 PM	#3
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,401	Re: 1969 Blazer seats install Maybe they all came with the utility seat holes when the custom seats were order they add the hole for them. __________________ 1972 GMC Jimmy 1/2 4X4 4wheel camper 1970 GMC Jimmy 1/2 4X4 350 1969 Chevy Blazer 1/2 4X4 307 1967 chevy LWB 3/4 396

01-02-2011, 04:09 PM	#4
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,764	Re: 1969 Blazer seats install My '72 didn't have both sets, dunno... __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

01-02-2011, 10:13 PM	#5
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,268	Re: 1969 Blazer seats install I think utility will match up with a bench seat in a pickup. I am welding in most of a pickup floor pan from a pickup from az in my blazer and it had the hole for my custom buckets just not the nut the other side has the nut. So I am sure they made them all for benches and then adjusted for the cst's



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.