Hedman LS Swap Headers - The 1947 - Present Chevrolet & GMC Truck Message Board Network

gringoloco · 03-14-2012, 02:10 PM

Anyone tried these? Looks like they have an extensive selection for our trucks including mid-length 1 3/4 to 3", and full length 1 3/4, stepped, and 1 7/8.

Searching around the site, I found NoLimit's Rob used the mids on their 'JT' truck and commented on the quality. Wondering if anyone has experience with the full length headers. Looking for full headers that don't hang below the rails...

http://www.hedmanhusler.com/1967-72-...S-Swap-Headers
Posted via Mobile Device

Last_Paladin · 03-22-2012, 08:41 PM

Quote:

Originally Posted by gringoloco

Anyone tried these? Looks like they have an extensive selection for our trucks including mid-length 1 3/4 to 3", and full length 1 3/4, stepped, and 1 7/8.

Searching around the site, I found NoLimit's Rob used the mids on their 'JT' truck and commented on the quality. Wondering if anyone has experience with the full length headers. Looking for full headers that don't hang below the rails...

http://www.hedmanhusler.com/1967-72-...S-Swap-Headers
Posted via Mobile Device

I wish they had stainless ones.

Daaaanz67 · 03-22-2012, 09:31 PM

Check out Doug thorley ls truck swap headers
Posted via Mobile Device

gringoloco · 03-23-2012, 10:47 PM

Upon further investigation, the hedmans are $pendy. The DTs are nice, but no longer full length. The search continues...
Posted via Mobile Device

Daaaanz67 · 03-24-2012, 09:11 AM

Dt are still available at summit last time I called about a month ago
Posted via Mobile Device

gringoloco · 03-24-2012, 02:11 PM

Yeah, at $615... Best I saw them around here was $450 shipped...

Super73 · 03-24-2012, 10:59 PM

I am currently trying a set of kooks trailblazer ss headers. Waiting for them to come in. Another member showed a few pics and they looked promising.
Posted via Mobile Device

**Shortie** · 03-25-2012, 12:48 AM

Im running the 3/4 length on my lq4, they are very high quality and are fully hidden by the frame

CROWN · 03-25-2012, 01:10 AM

Why won't anyone try headers from a corvette c5 or c6??? Those cars are super low and have really really tight engine bays. U literally have to unbolt the drivers side motor mount and jack the motor up to get the drivers side header in. But anyway they should work well!
Posted via Mobile Device

gringoloco · 03-25-2012, 06:57 PM

Corvette headers run towards the center of the car, to facilitate fitting into the tunnel- that may cause problems on a 'normal' car...

**Clyde65** · 03-25-2012, 09:40 PM

I have Sanderson shorties and they fit perfectly.
Posted via Mobile Device

lt155ruck · 03-25-2012, 09:52 PM

Quote:

Originally Posted by Clyde65

I have Sanderson shorties and they fit perfectly.
Posted via Mobile Device

What part number are you using

Shon · 03-26-2012, 03:14 PM

Quote:

Originally Posted by gringoloco

Yeah, at $615... Best I saw them around here was $450 shipped...

$625 shipped now from me.
if interested I will check to see if they are in stock at DT.

dkauffman05 · 03-26-2012, 07:58 PM

I love the way my dynatech 2nd gen camaro headers fit.

gringoloco · 03-26-2012, 10:20 PM

Schoenfelds are looking better every day...
Posted via Mobile Device

03-14-2012, 02:10 PM	#1
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Hedman LS Swap Headers Anyone tried these? Looks like they have an extensive selection for our trucks including mid-length 1 3/4 to 3", and full length 1 3/4, stepped, and 1 7/8. Searching around the site, I found NoLimit's Rob used the mids on their 'JT' truck and commented on the quality. Wondering if anyone has experience with the full length headers. Looking for full headers that don't hang below the rails... http://www.hedmanhusler.com/1967-72-...S-Swap-Headers Posted via Mobile Device __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-22-2012, 09:31 PM	#3
Daaaanz67 Registered User Join Date: Nov 2011 Location: Idaho Posts: 857	Re: Hedman LS Swap Headers Check out Doug thorley ls truck swap headers Posted via Mobile Device

03-23-2012, 10:47 PM	#4
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: Hedman LS Swap Headers Upon further investigation, the hedmans are $pendy. The DTs are nice, but no longer full length. The search continues... Posted via Mobile Device __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-24-2012, 09:11 AM	#5
Daaaanz67 Registered User Join Date: Nov 2011 Location: Idaho Posts: 857	Re: Hedman LS Swap Headers Dt are still available at summit last time I called about a month ago Posted via Mobile Device

03-24-2012, 02:11 PM	#6
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: Hedman LS Swap Headers Yeah, at $615... Best I saw them around here was $450 shipped... __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-24-2012, 10:59 PM	#7
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: Hedman LS Swap Headers I am currently trying a set of kooks trailblazer ss headers. Waiting for them to come in. Another member showed a few pics and they looked promising. Posted via Mobile Device __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

03-25-2012, 12:48 AM	#8
Shortie Junior Member Join Date: Aug 2010 Location: Fergus, Ontario Posts: 50	Re: Hedman LS Swap Headers Im running the 3/4 length on my lq4, they are very high quality and are fully hidden by the frame

03-25-2012, 01:10 AM	#9
CROWN Registered User Join Date: Aug 2011 Location: Texas Posts: 22	Re: Hedman LS Swap Headers Why won't anyone try headers from a corvette c5 or c6??? Those cars are super low and have really really tight engine bays. U literally have to unbolt the drivers side motor mount and jack the motor up to get the drivers side header in. But anyway they should work well! Posted via Mobile Device

03-25-2012, 06:57 PM	#10
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: Hedman LS Swap Headers Corvette headers run towards the center of the car, to facilitate fitting into the tunnel- that may cause problems on a 'normal' car... __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-25-2012, 09:40 PM	#11
Clyde65 1965 Chevy C10, 2005 4.8L/4l60 Join Date: Aug 2004 Location: DFW Texas Posts: 8,547	Re: Hedman LS Swap Headers I have Sanderson shorties and they fit perfectly. Posted via Mobile Device __________________ Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 *support our troops!*

03-26-2012, 07:58 PM	#14
dkauffman05 Registered User Join Date: Jan 2008 Location: Cumming, Georgia Posts: 417	Re: Hedman LS Swap Headers I love the way my dynatech 2nd gen camaro headers fit.

03-26-2012, 10:20 PM	#15
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: Hedman LS Swap Headers Schoenfelds are looking better every day... Posted via Mobile Device __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.