Trouble installing BB in truck - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Maxian · 06-01-2013, 02:25 AM

I'm having trouble installing my BB in my '69 truck
Using factory BB tower stands and using the correct engine side mounts.
Just doesn't seem to fit. Like the engine is a 1/4 inch too wide.
I can get one side to bolt up, but not the other. I can get close, just can't get both to line up.
I've loosened the stands to see if there was any play, but will only adjust front - rear.
Almost as if I shaved 1/8 off one mount it would settle in correctly.
Any thoughts or ideas regarding this ? Common issue ?

Thank you

**leddzepp** · 06-01-2013, 02:29 AM

I would guess that your frame is tweaked. Common with these 40+ year old trucks.
Posted via Mobile Device

Maxian · 06-01-2013, 02:32 AM

Not tweeked. Truck in family since 1969.
Never wrecked or abused. Az truck, no rust. Frame pristine.
Hmmm

yukon · 06-01-2013, 02:33 AM

Some pictures would help.

Maxian · 06-01-2013, 02:48 AM

Ok, figured out how to add a picture.

**leddzepp** · 06-01-2013, 03:01 AM

Quote:

Originally Posted by Maxian

Not tweeked. Truck in family since 1969.
Never wrecked or abused. Az truck, no rust. Frame pristine.
Hmmm

Even without abuse, I would still suspect normal wear and tear, given the age and the fact that it is not that far off when you try and set the engine in place. Is it possible the mounts are tweaked slightly?

Maxian · 06-01-2013, 03:03 AM

Brand new GM mounts.
Truck might have 40k at most,

Maxian · 06-01-2013, 03:04 AM

Any suggestions ?
I was thinking of just shaving one mount down ????

yukon · 06-01-2013, 03:38 AM

Can you take a shot of each side from the top?

skorpioskorpio · 06-01-2013, 04:06 AM

Desperate times require desperate measures, but Pepto is for settling stomachs not engines.

cdowns · 06-01-2013, 06:47 AM

is the motor hanging on the lift?? // engine weight on lift an a couple of large screwdrivers is the way i've been lining up engine mounts fer years

Shyguy · 06-01-2013, 07:37 AM

We used '74 stands and mounts when we put the '74 454 in my '69 frame and it settled in nicely.

**Tom Vogel** · 06-01-2013, 09:40 AM

Quote:

Originally Posted by cdowns

is the motor hanging on the lift?? // engine weight on lift an a couple of large screwdrivers is the way i've been lining up engine mounts fer years

^^^X2 and loosen everything up well first.

Rufton · 06-01-2013, 09:46 AM

Had some issue shooting BB 305 V6 mounts. I loosened mounts for wiggle room. I moved engine lift chain to front of engine so I could rock/list engine back and forth. Shot it then snugged er down.

Maxian · 06-02-2013, 09:42 AM

Thank you everybody, got her in !

06-01-2013, 02:25 AM	#1
Maxian Registered User Join Date: Nov 2012 Location: Az Posts: 26	Trouble installing BB in truck I'm having trouble installing my BB in my '69 truck Using factory BB tower stands and using the correct engine side mounts. Just doesn't seem to fit. Like the engine is a 1/4 inch too wide. I can get one side to bolt up, but not the other. I can get close, just can't get both to line up. I've loosened the stands to see if there was any play, but will only adjust front - rear. Almost as if I shaved 1/8 off one mount it would settle in correctly. Any thoughts or ideas regarding this ? Common issue ? Thank you

06-01-2013, 02:29 AM	#2
leddzepp Moderator Join Date: May 2007 Location: Southern Cal Posts: 20,117	Re: Trouble installing BB in truck I would guess that your frame is tweaked. Common with these 40+ year old trucks. Posted via Mobile Device __________________ 1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul

06-01-2013, 02:32 AM	#3
Maxian Registered User Join Date: Nov 2012 Location: Az Posts: 26	Re: Trouble installing BB in truck Not tweeked. Truck in family since 1969. Never wrecked or abused. Az truck, no rust. Frame pristine. Hmmm

06-01-2013, 02:33 AM	#4
yukon Registered User Join Date: Jun 2011 Location: fairbanks, ak Posts: 26	Re: Trouble installing BB in truck Some pictures would help.

06-01-2013, 02:48 AM	#5
Maxian Registered User Join Date: Nov 2012 Location: Az Posts: 26	Re: Trouble installing BB in truck Ok, figured out how to add a picture. Attached Images

06-01-2013, 03:03 AM	#7
Maxian Registered User Join Date: Nov 2012 Location: Az Posts: 26	Re: Trouble installing BB in truck Brand new GM mounts. Truck might have 40k at most,

06-01-2013, 03:04 AM	#8
Maxian Registered User Join Date: Nov 2012 Location: Az Posts: 26	Re: Trouble installing BB in truck Any suggestions ? I was thinking of just shaving one mount down ????

06-01-2013, 03:38 AM	#9
yukon Registered User Join Date: Jun 2011 Location: fairbanks, ak Posts: 26	Re: Trouble installing BB in truck Can you take a shot of each side from the top?

06-01-2013, 04:06 AM	#10
skorpioskorpio Registered User Join Date: Nov 2010 Location: Los Angeles, CA Posts: 1,018	Re: Trouble installing BB in truck Desperate times require desperate measures, but Pepto is for settling stomachs not engines.

06-01-2013, 06:47 AM	#11
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Trouble installing BB in truck is the motor hanging on the lift?? // engine weight on lift an a couple of large screwdrivers is the way i've been lining up engine mounts fer years __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

06-01-2013, 07:37 AM	#12
Shyguy Junior Member Join Date: Dec 2006 Location: Southeast Missouri Posts: 2,436	Re: Trouble installing BB in truck We used '74 stands and mounts when we put the '74 454 in my '69 frame and it settled in nicely. __________________ '67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E.

06-01-2013, 09:46 AM	#14
Rufton Registered User Join Date: Apr 2013 Location: Knoxville TN Posts: 1,170	Re: Trouble installing BB in truck Had some issue shooting BB 305 V6 mounts. I loosened mounts for wiggle room. I moved engine lift chain to front of engine so I could rock/list engine back and forth. Shot it then snugged er down. Attached Images

06-02-2013, 09:42 AM	#15
Maxian Registered User Join Date: Nov 2012 Location: Az Posts: 26	Re: Trouble installing BB in truck Thank you everybody, got her in !



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.