1967 gmc 3/4 4x4

[briank]

Just picked up a 1967 gmc 3/4 ton longbox 4x4.Sheetmetal is pretty much toast, gonna part it out, anything desirable on this I should look for?
Posted via Mobile Device

[GMCJOE]

Originally Posted by briank

Just picked up a 1967 gmc 3/4 ton longbox 4x4.Sheetmetal is pretty much toast, gonna part it out, anything desirable on this I should look for?
Posted via Mobile Device

Pretty much anything that is salvageable. Almost anything and everything has a demand when it comes to these trucks. You can use the parts board as a basis of what people usually are looking for or parting out on these.

[briank]

How about the v6 engine? It has oil in it, I need to see if it will turn over. Too bad its so rusty this has to be a somewhat low production truck.
Posted via Mobile Device

[GMCJOE]

GMC put there v-6(big block 305) engines in a bunch of the trucks. Though, I don't think many after 67. Far as I know, they aren't worth too much but there is still a desire for them with some people. Most people that got one with the v-6 have swapped to a v-8. I would suggest putting everything on the parts board with prices and see what you can get.

[RPBurris]

Post some pics?? I have been watching a few on Craigslist in the area. Might be interested in the rolling chassis...Only if posted to the Parts forum of course..

[nbrfd007]

Power steering pump and brackets if it is a V-6. I would like to have them,
Thanks,
Tim

[Leroy-B1]

What about center cap for steering wheel
Posted via Mobile Device

[GMCJOE]

If this thing is going to get parted out, take it to the parts board and speak for parts there, not on here.

If I was you braink, don't sell the accessories off the engine. These engines are a little rare to come by these days, and parts are hard to find. If you part the accessories out, you might not be able to see the engine. From a little research, most of these engines that have sold on the internet have went anywhere between $300-500. All different conditions. Good luck.

[briank]

Thanks for the opinions, I will probably sell it whole on the board rather than part it, not worth the hassle. At least I wont take it to the crusher
Posted via Mobile Device

[GMCJOE]

Could you add a pic of this beast.... Wish I was home, I would make an offer on the whole truck. I want a 4x4 project...lol Just another thing to tick the wife off, guess she is lucky I am gone right now..lol

Good luck... But yeah, add a pic cause I think at least a few of use would like to see this thing.

[briank]

Im gonna try to post a pic from my phone so here goes
Posted via Mobile Device

[GMCJOE]

Looks like a project for someone. Pretty cool find.

[briank]

Basically it is a running gear, the cab is shot as is the box. Too bad because its an early truck. Still need to see if she turns over.
Posted via Mobile Device

[GMCJOE]

Actually it doesn't seem all that bad compared to what I have seen some people start with. You should see some of the trucks we have started with in Missouri. Looks like a new floor in the cab and rockers, probably a new floor in the bed, front fenders repaired or replaced. Not a bad basis for some to start off with that had the time and money into it.

But parting it out isn't a bad thing either, way better than the crusher. Have fun.

[67Texas4x4]

I just picked up the same truck. If yours has power assist steering, I'd be interested. I don't think it looks too bad either though.
The 67 I picked up is pretty tight but the steering is a bear. The big block V6 is pretty strong.
Posted via Mobile Device

[briank]

I actually sold this truck to a board member in Texas
Posted via Mobile Device