|
03-10-2014, 01:25 PM
|
#1 |
|
Registered User
Join Date: Jul 2013
Location: Bradenton Fl.
Posts: 52
|
How Do I ?
How do I remove this knob ? Thanks Doc
|
|
|
|
03-10-2014, 01:26 PM
|
#2 |
|
Registered User
Join Date: Jul 2013
Location: Bradenton Fl.
Posts: 52
|
Re: How Do I ?
The heater nob ? Thanks Doc
|
|
|
|
|
03-10-2014, 02:05 PM
|
#3 |
|
Senior Member
 
Join Date: Jan 2011
Location: Hayes Va
Posts: 4,569
|
Re: How Do I ?
Should be a set screw in it I think.
Jimmy
__________________
60 to 66 Chevy and GMC window decals http://67-72chevytrucks.com/vboard/s...d.php?t=661131 Good friends, good food and a hotrod what else do you need? 1966 BBW long fleet Daily driver 1965 BBW short fleet Sold and going to a good home 1965 Suburban 2003 3500 Duramax 2005 Ultra Classic |
|
|
|
|
03-10-2014, 02:50 PM
|
#4 |
|
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: How Do I ?
Looks to me like a cable pull. I'd think you need to disconnect the far end of the cable, and remove the nut or clip that is holding the bezel to the dash and remove the entire cable assembly. If you can straighten the rod enough to reuse the cable, the best way to remove the knob is probably to clamp the rod in a vise, protected by wood or cardboard, and place a crescent wrench against the bottom of the knob and give it a couple of hits with a plastic hammer. All of the dash knobs on my truck as attached with JB Weld.
__________________
My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=444502 |
|
|
|
|
03-10-2014, 04:32 PM
|
#5 |
|
Registered User
Join Date: Jul 2013
Location: Bradenton Fl.
Posts: 52
|
Re: How Do I ?
It is sitting loose on the dash with the bezel floating, I would be happy to use a clip if that is possible. The cable does pull out and is also a 3 speed switch. What kind of clip do I need to get it tight to the dash it does have treads on the shaft that comes thru the dash but without removing the nob theirs no way to get a nut on it. Thanks Doc
|
|
|
|
|
03-10-2014, 07:28 PM
|
#6 |
|
Who Me?
Join Date: Sep 2010
Location: Royal Palm Beach, FL
Posts: 4,067
|
Re: How Do I ?
Can you see a cable attached?
__________________
 Steve1997 Tahoe LT 4D 2WD (DD) 2001 Blazer 4D 2WD 1961 Apache 10 (sold) 1965 C10 Stepper (sold) |
|
|
|
|
03-11-2014, 07:05 AM
|
#7 | |
|
Registered User
Join Date: Jul 2013
Location: Bradenton Fl.
Posts: 52
|
Re: How Do I ?
Quote:
|
|
|
|
|
|
03-11-2014, 12:08 PM
|
#8 |
|
Registered User
Join Date: Jul 2013
Location: Bradenton Fl.
Posts: 52
|
Re: How Do I ?
OK My eyes SUCK ! Found a set screw on the nob, All fixed. Thanks Doc.
|
|
|
|
|
03-11-2014, 06:11 PM
|
#9 |
|
Who Me?
Join Date: Sep 2010
Location: Royal Palm Beach, FL
Posts: 4,067
|
Re: How Do I ?
Nice job Doc!! We knew you could do it!!
__________________
Steve1997 Tahoe LT 4D 2WD (DD) 2001 Blazer 4D 2WD 1961 Apache 10 (sold) 1965 C10 Stepper (sold) |
|
|
|
|
03-12-2014, 07:12 AM
|
#10 |
|
Registered User
Join Date: Jul 2013
Location: Bradenton Fl.
Posts: 52
|
Re: How Do I ?
Thank You.
|
|
|
|
|
03-12-2014, 10:09 AM
|
#11 | |
|
Registered User
Join Date: Jul 2013
Location: Bradenton Fl.
Posts: 52
|
Re: How Do I ?
Quote:
|
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
