Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
03-23-2014, 09:33 PM | #1 |
Registered User
Join Date: Mar 2014
Location: Olympia Washinton
Posts: 21
|
Smoke from breather and dipstick
Like the title say I'm getting a light steamy smokey burnt oil smelling steam from my breather and dipstick any ideas on what's going on? It's a 350 sb
|
03-23-2014, 09:51 PM | #2 |
Registered User
Join Date: Jul 2011
Location: Des Moines, Iowa
Posts: 3,016
|
Re: Smoke from breather and dipstick
How's the oil check out? look/level
Check you pcv filter
__________________
project: "my happy mess" |
03-23-2014, 09:54 PM | #3 |
Registered User
Join Date: Jul 2010
Location: Mesa, AZ
Posts: 513
|
Re: Smoke from breather and dipstick
Make sure the PCV valve is not stuck closed. You should be able to hear it rattle when you shake it. When engine is running at idle, you should have good suction at the PCV valve. Smoke is from blow by not properly being evacuated. If your PCV valve is operating normally and you have blow by, I am afraid your problems are deeper in the engine.
__________________
JB from AZ 1969 Chevy Sub K10 1957 Chevy 3200 1962 VW Beetle 1957 Willys CJ5 |
03-23-2014, 10:00 PM | #4 |
Registered User
Join Date: Mar 2014
Location: Olympia Washinton
Posts: 21
|
Re: Smoke from breather and dipstick
Pcv valves solid replacing it on the tune up anyways oil levels a little low gotta do the oil Pan gasket it did not happen till recently and it has lost oil since I drove it more could that be the case low on oil? I really hope it's not my rings
|
03-23-2014, 10:08 PM | #5 |
Who Changed This?
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 10,692
|
Re: Smoke from breather and dipstick
Rings. It's blow-by, unless the engine is so overheated that it's cooking, which is going to mean rings, anyway.
__________________
~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA |
03-23-2014, 10:10 PM | #6 |
Registered User
Join Date: Jul 2011
Location: Des Moines, Iowa
Posts: 3,016
|
Re: Smoke from breather and dipstick
check your compression
__________________
project: "my happy mess" |
03-23-2014, 10:10 PM | #7 |
Registered User
Join Date: Jul 2013
Location: Forestburg, Texas
Posts: 659
|
Re: Smoke from breather and dipstick
Chances are the engine is just flat worn out. A correctly working PCV will mask the problem by sucking all the smoke out of the CC and reburning it. The problem is that the compression rings are allowing blow-by.
__________________
Mark Jesus is the Way! 2003 2500HD CCLB Duramax/Ali (Clifford) 2014 2SS/RS black on black Camaro (Betty) 2006 Pontiac SOLSTICE silver/black (Lula-Bell) 1970 C/10 Short Wide (Peggy) 1964 C/10 Short Step (Hambone) RIP Jimmy Hamilton Thank you for the trucks |
03-23-2014, 10:12 PM | #8 |
Registered User
Join Date: Jul 2011
Location: Des Moines, Iowa
Posts: 3,016
|
Re: Smoke from breather and dipstick
how many miles?
__________________
project: "my happy mess" |
03-23-2014, 10:14 PM | #9 |
Registered User
Join Date: Mar 2014
Location: Olympia Washinton
Posts: 21
|
Re: Smoke from breather and dipstick
Sounds like I'm better off buying a new 350 the miles are unknown but it runs and idles like a champ. That's why I'm so confused but a compression test will tell the true story thanks guys
|
03-24-2014, 09:46 AM | #10 |
Registered User
Join Date: Jun 2010
Location: Upland Ca
Posts: 4,147
|
Re: Smoke from breather and dipstick
All engines have blow by, even well broken in ones with great compression. On a used engine it is perfectly normal to have a little blow by wafting out of the breather, a little. Now if it's clouding up the engine bay, that's a different matter. While a compression test will is useful in looking at the over condition of the rings and valves, only a leak down test will tell the real story.
__________________
1972 C10 SWB, Air, PS, PB, 350/350THM. Second owner. 1965 Corvette roadster, 44K miles, 327/365 SHP, 4 speed, side exhaust, knockoffs, teak, second owner (bought in 1970), Have ALL numbers matching components. My frame off restoration thread: http://67-72chevytrucks.com/vboard/s...d.php?t=556703 |
03-24-2014, 10:50 AM | #11 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: Smoke from breather and dipstick
if it is used infrequently it will smoke from the moisture that builds up inside the block and will gradualyy go away when the block gets up to operating temps
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
03-24-2014, 10:54 AM | #12 |
Registered User
Join Date: Aug 2009
Location: Bowser
Posts: 13,732
|
Re: Smoke from breather and dipstick
Check the pcv vac hose. They collapse if you use the wrong one.
|
03-24-2014, 11:01 AM | #13 |
Registered User
Join Date: Feb 2014
Location: Pocahontas Arkansas
Posts: 684
|
Re: Smoke from breather and dipstick
Excessive blow by like stated previously is compression. usually rings. could be a bad piston. sometimes they burn part of the top away? Ive seen broken rings and cracked ring lands on just one cyl. run a compression check. a seeping head gasket can cause smoke also. many times a engine that isn't used but for short trips (city driving) and doesn't get thouroughly warmed up will collect significant condensation and that evaporating looks similar to blow by. A 250 in a 65 that was perfect before I left home burnt a piston in Dallas Tex traffic. I made it home but the blow by was teriffic burnt a gallon of lucas oil additive on the way home.
|
Bookmarks |
Tags |
72 c10 |
|
|