WANTED; 350 w/4 bolt main block! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Moloko · 01-22-2004, 09:23 PM

Like the title says. I need a 4 bolt main 350 block that is either freshly bored .030 or does not need any boring. Thanks.

Mike76251 · 01-24-2004, 07:53 AM

Since this is slipping down......
I needed a one-piece 4-bolt last year and could not find one anywhere.......all I could find was 2-bolts.
I wound up going to the Chevy place (parts dept) and ordering one.
It was around $600 new.
Another "funny" to do with that block.........Jeg's sent me the wrong-sized pistons (needed 4" bore and they sent +.030s),
I called to get a return number and the tech. said "just bore that block out and use the ones you have" ARRRRRRRRRRGGGGG!!!
They finally took them back after 15 minutes on the phone.

*1972C10* · 01-24-2004, 02:47 PM

Why the obsession with 4 bolt mains?

phantom dually · 01-24-2004, 03:54 PM

Find a good 2 bolt and use the Milodon conversion main caps. They are stronger than a 4 bolt.

rogf4 · 01-25-2004, 01:59 AM

I have a 4 bolt 350 standard bore with a nodular forged crank $150.00 plus shipping I also have fresh 400 .040 over new cam bearings new brass freeze plugs ran about 1 hour with new carb and the center screw came out of the bottom of carb and landed on top of piston needs a sleeve and ready to put back together
Roger

01-22-2004, 09:23 PM	#1
Moloko Hoarding Rusty Objects Join Date: Aug 2002 Location: Slatington, PA Posts: 267	WANTED; 350 w/4 bolt main block! Like the title says. I need a 4 bolt main 350 block that is either freshly bored .030 or does not need any boring. Thanks. __________________ 1985 Chevrolet K20 Silverado 1994 GMC Yukon Follow me on Youtube! - http://www.youtube.com/user/FuelInjectionSucks

01-24-2004, 03:54 PM	#4
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	Find a good 2 bolt and use the Milodon conversion main caps. They are stronger than a 4 bolt. __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

01-24-2004, 07:53 AM	#2
Mike76251 Senior Member Join Date: Mar 2003 Posts: 2,499	Since this is slipping down...... I needed a one-piece 4-bolt last year and could not find one anywhere.......all I could find was 2-bolts. I wound up going to the Chevy place (parts dept) and ordering one. It was around $600 new. Another "funny" to do with that block.........Jeg's sent me the wrong-sized pistons (needed 4" bore and they sent +.030s), I called to get a return number and the tech. said "just bore that block out and use the ones you have" ARRRRRRRRRRGGGGG!!! They finally took them back after 15 minutes on the phone.

01-24-2004, 02:47 PM	#3
1972C10 Account Suspended Join Date: Dec 2003 Location: Texas Posts: 2,686	Why the obsession with 4 bolt mains?

01-25-2004, 01:59 AM	#5
rogf4 Registered User Join Date: Nov 2003 Location: whitesburg,Tn Posts: 223	I have a 4 bolt 350 standard bore with a nodular forged crank $150.00 plus shipping I also have fresh 400 .040 over new cam bearings new brass freeze plugs ran about 1 hour with new carb and the center screw came out of the bottom of carb and landed on top of piston needs a sleeve and ready to put back together Roger



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.